display PEUGEOT 807 2002 Owners Manual

Page 2 of 181

18-11-2002
14 Windscreen washwipe
stalk.
Trip computer stalk.
15 Audio remote control stalk.
16 Interior alarm disarming
switch.
17 Electric mirror controls.
Window controls.
Rear window locking control.
18 Steering lock and ignition.
19 Dynamic stability control
(ESP/ASR) switch.
20 Headlamp height
adjustment.
21 Fuse box.
22 Handbrake.
23 Steering wheel adjustment
control.
24 Battery / Fuse box.
25 Heated seat switches.
26 Storage. 27
Gear lever.
28 Cooled compartment.
29 Ashtray / Can holder.
30 Storage compartment
or remote control keypad.
31 Lighter / 12 V accessories
socket.
32 Hazard warning lights
switch.
33 Air conditioning controls.
34 Passenger compartment
temperature sensor.
35 Passenger lower glove box.
36 Passenger air bag.
37 Side vent.
38 Bonnet release.
39 Passenger air bag disarming
switch*.
* According to country.
YOUR 807 AT A GLANCE3
1 Side window demisting
vents.
2 Speaker (tweeter).
3 Windscreen demisting
vents.
4 Passenger upper glove box.
5 Brightness sensor.
6 Instrument panel /
Multifunction display.
7 RB3, RD3, RT3 audio
equipment with flap.
8 Central vents.
9 Driver’s upper glove box.
10 Lights and direction
indicators stalk.
11 Cruise control controls.
12 Check unit.
13 Driver’s air bag.
Horn.

Page 13 of 181

18-11-2002
YOUR 807 AT A GLANCE14REAR PARKING
ASSISTANCE
This system, installed in the rear
bumper, detects any obstacle
(person, vehicle, tree, barrier,
kerb, ...) behind the vehicle.
Switching on
With the engine running, the sys
tem is activated when reverse
gear is engaged. A bleep indi
cates that it is active.
The proximity information is
given by an audible signal, con
sisting of bleeps which becomes
more rapid as the vehicle
approaches the obstacle.
When the distance between the
rear of the vehicle and the obsta
cle is less than approximately
twentyfive centimetres, the audi
ble signal becomes continuous. ➜When you change to
neutral, the system
becomes inactive
again. TYRE UNDERINFLATION
DETECTION
Sensors check the pressure of
the tyres while driving and trigger
a warning in the event of a mal
function (speed above 15 mph
[25 km/h]).
Tyre(s) underinflated
When this message appears on
the multi–function display, accom
panied by an audible signal, have
the pressure of the tyres checked
as soon as possible.
Tyre(s) punctured
The appearance of this message,
accompanied by an audible sig
nal, is followed by illumination of
the
STOP warning light.
Stop immediately, avoiding any
sharp action on the steering
wheel or the brakes.
Change the damaged (punctured
or significantly underinflated)
wheel and have the pressure of
the tyres checked as soon as
possible.
Note: if the damaged wheel is
stored in the boot temporarily, it
will transmit this message again
as a reminder that it must be
repaired, which will prevent
another warning of the same type
being displayed.
The spare wheel does not have a
sensor. X type pressure sensor(s)
missing
The appearance of this message,
accompanied by an audible
warning, indicates that one wheel
(or more) is no longer detected.
Consult a PEUGEOT dealer to
have the faulty sensor(s)
replaced.
Warning:
this message is also
displayed when one of the
wheels is removed from the vehi
cle (for repair) or when a wheel is
fitted which is not equipped with
a sensor (winter tyres).
This system does not eliminate
the need to have the pressure
of the tyres checked regularly.
131141

Page 18 of 181

PEUGEOT SERVICING
22
A few seconds after the ignition is
switched on, the total distance recor
der resumes normal operation and
the display shows the total and trip
distances.
The distance remaining before the
next service is less than 500 miles.
When the ignition is switched on and
for a few seconds, the symbol
flashes and the distance remaining
is displayed:
A few seconds after the ignition is
switched on, the oil level is dis
played, then the distance recorder
resumes normal operation and the
spanner remains lit. This indicates
that a service should be carried out
shortly.
SERVICE INDICATOR
Located on the instrument panel with
the total distance recorder (total and
trip distances), this programmes ser
vice intervals depending on the use
of the vehicle.
Operation
A few moments after the ignition has
been switched on, the spanner sym
bolising a service lights up; the dis
play for the total distance recorder
tells you (in round figures) the dis
tance remaining before your next
service.
Example: 4,800 miles remain before
the next service is due. When the
ignition is switched on and for a few
seconds, the display shows: The service is overdue
Each time the ignition is switched on
and for a few seconds, the symbol
flashes and the excess distance is
displayed.
Note:
with the engine running the
symbol flashes until the service has
been carried out.
18-11-2002

Page 19 of 181

PEUGEOT SERVICING23
Zero reset Y our PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the reset procedure is as
follows:
 Switch off the ignition,
 Press and hold the trip recorder
reset button,
 Switch on the ignition.
The display begins a countdown.
When the display shows "=0", relea
se the button; the service symbol
disappears.
Important: after this operation, if
you wish to disconnect the battery,
lock the vehicle and wait for at least
five minutes, otherwise the zero re
set will not be registered.
MAINTENANCE OF PARTS SUBJECT TO WEAR AND A CHECK OF
CONSUMABLES
Certain essential components on your vehicle are subject to checks a t specific
frequencies.
• The brake fluid is to be replaced at a maximum of every 36,000/40,000 miles
(60 000km) or every two years;
• The pollen filter must be checked at each serviceby a PEUGEOT dealer
(services and intermediate visits) or more often, depending on the environ
ment (dust, pollution, etc.);
• For HDI turbo diesel engines with particulate emission filter , maintenance
of the filterand topping up of the additive reservoirmust be carried out at a
maximum of every 48,000 miles (80 000 km) by a PEUGEOT dealer;
• Replacement of the timing belt: contact a PEUGEOT dealer.
• Air bags and pretensioning parts on seat belts must be checked every
10 years.
• Tyre pressure sensors are to be replaced every 10 years.
• The check on tyre inflation presure must be carried out cold at least once a
month.
Note: the engine coolant does not have to be replaced.
18-11-2002

Page 24 of 181

INSTRUMENTS AND CONTROLS
28
INSTRUMENTS AND CONTROLS
A warning light continuously lit, or flashing with the eng ine running, is an indication of a malfunction in the
relevant unit. Some warning lights may be linked to buzzer s and a message on the multi–function display. Do not
ignore this warning: contact a PEUGEOT dealer as quickly a s possible.
If the central STOP warning light comes on when you are d riving, stop immediately where it is safe to do so.
Central STOP warning light
This is linked to the "engine oil pressure", "coolant level low " and "brake fluid level" warning lights and the coolant
temperature gauge and puncture warnings, indicated by a message on the multifunction display.
It comes on each time the ignition is switched on.
Stop immediately .
Contact a PEUGEOT dealer.
Engine oil pressure warning light
This is linked to the central STOPwarning light.
If it comes on with the engine running, it is accompanied b y an audible signal and the message "Oil pressure low"
or "Top up engine oil" on the multifunction display.
Stop immediately .
In the case of a lack of oil in the lubricating circuit, top up the level.
Contact a PEUGEOT dealer without delay.
Low coolant level warning light
This is linked to the central STOPwarning light.
It comes on each time the ignition is switched on.
Illumination of this warning light, with the engine run ning, is accompanied by an audible signal and the message
"Top up coolant" on the multifunction display.
Stop immediately.
Warning: allow the engine to cool before topping up.
The cooling system is pressurised.
To prevent the risk of scalding, unscrew the cap by two turns to allow the pressure to drop.
Once the pressure has dropped, remove the cap and topup the le vel.
Contact a PEUGEOT dealer.
18-11-2002

Page 25 of 181

Handbrake,low brake fluid level and electronic brake force distri bution warning light
This is linked to the central STOPwarning light.
It comes on each time the ignition is switched on.
This warning light is accompanied by an audible signal and a message on the multifunction display indicating the
cause of the warning:
– "Handbrake on" , if the handbrake is on or not released correctly while driving ,
– "Brake fluid low" in the event of an excessive drop in the brake fluid level (if the warning light remains lit even with the
handbrake released),
– "Braking fault" , displayed at the same time as the ABS warning light, indicat ing an electronic brake force distribution
system fault.
Stop immediately.
Contact a PEUGEOT dealer.
INSTRUMENTS AND CONTROLS 29
Dynamic stability control warning light (ESP/ASR)
This comes on each time the ignition is switched on.
If it remains on or comes on with the engine running and th e vehicle moving, it is accompanied by an audible
signal and the message "ESP/ASR not operational" on the multifunction display.
Contact a PEUGEOT dealer.
It flashes when the system is activated and is lit continuously when the system is switched off.
Antilock braking system (ABS) warning light
This comes on each time the ignition is switched on.
If it remains on or comes on above 8 mph (12 km/h), it indicates a
malfunction of the ABS.
However, the vehicle retains conventional servoassisted braking.
Illumination of this warning light is accompanied by an aud ible signal and the message "ABS fault" on the multifunction
display.
Contact a PEUGEOT dealer.
18-11-2002

Page 26 of 181

INSTRUMENTS AND CONTROLS
30
Cruise control indicator light
This indicator light comes on when the function is activated.
Battery charge warning light
This comes on each time the ignition is switched on.
If it comes on with the engine running, it is accompanied b y an audible signal and the message "Low battery
charge" on the multifunction display.
It indicates faulty operation of the charging circuit (loose b attery terminals, a cut or slack alternator belt, an alternator f ault).
Contact a PEUGEOT dealer.
Engine diagnostics warning light
This comes on each time the ignition is switched on.
If it comes on with the engine running, accompanied by an a udible signal and the message "Emission control
system problem" on the multifunction display, it indicates a malfunction in the emission control sy stem.
If it flashes with the engine running, accompanied by an a udible signal and the message "Catalytic converter faulty"on
the multifunction display, it indicates a malfunction in th e injection or ignition sy stem. There is a risk of damage to t he
catalytic converter (petrol engines only).
Contact a PEUGEOT dealer without delay.
Note: following prolonged operation of the vehicle at very low sp eed or at idle, you may, in exceptional circumstances, notice
emissions of water vapour at the exhaust on acceleration. This d oes not have any effect on the vehicle's performance or on
the environment.
Diesel preheat indicator light
This comes on each time the ignition is switched on.
In cold weather, wait until it goes out before trying th e starter.
18-11-2002

Page 27 of 181

INSTRUMENTS AND CONTROLS31
Passenger air bag disarming indicator light
This comes on for a few seconds each time the ignition is switch ed on.
Illumination of this indicator light is accompanied by an au dible signal and the message"Passenger air bag
disarmed" on the multifunction display.
If the passenger air bag is disarmed, the indicator light comes on when the ignition is switched on and remains on.
In all cases, if the indicator light flashes, contact a PEUGEOT dealer.
Front, side and curtain air bags warning light
This warning light comes on when the ignition is switched o n.
Illumination of this warning light, with the engine run ning, is accompanied by an audible signal and the message
"Air bag fault" on the multifunction display, indicating a front, side or cu rtain air bag fault.
Contact a PEUGEOT dealer.
Driver's seat belt warning light
With the engine running, this indicator light comes on, acco mpanied by an audible signal at a speed above 6 mph
(10 km/h) and the message "Seat belt not fastened" on the multifunction display, if the driver's seat belt is no t
fastened.
Low fuel level warning light
This light comes on each time the ignition is switched on.
When the warning light comes on, accompanied by the message "Fuel level low"on the multifunction display,
there is enough fuel remaining to drive approximately 30 miles (50 km). The tank capacity is approximately 80 litres.
This light flashes to indicate a malfunction of the fuel gauge or cuttingoff of the fuel supply, if it is accompanie d by the
message "Fuel circuit neutralised" on the multifunction display.
Restore the supply (refer to the "Practical Information § Fuel Su pply CutOff" section) or contact a PEUGEOT dealer,
depending on the circumstances.
Note: some functions can be configured by your PEUGEOT dealer.
18-11-2002

Page 28 of 181

INSTRUMENTS AND CONTROLS
32
In zoneA,the temperature is correct.
In zone B, the temperature is too high. The central STOPwarning light and the
maximum coolant temperature warning light 1come on, accompanied by an
audible signal and the message "Coolant temp. too high"on the multifunction
display.
You must stop immediately.
Warning : wait for the engine to cool before topping up the le vel.
The cooling system is pressurised.
In the event of a breakdown and in order to avoid any risk of scalding, unscrew
the cap two turns to allow the pressure to drop.
When the pressure has dropped, remove the cap and top up the level.
Contact a PEUGEOT dealer.
Instrument panel with
monochrome screen
Instrument panel with colour
screen
Coolant temperature indicator light
18-11-2002

Page 30 of 181

Maximum
Minimum
Check the level with
the dipstick and top it
up.
The figure shown is
only correct if the vehicle has been
on stable, level ground, with the
engine stopped, for 10 minutes.
No oil
The message "Top
up the oil" appears
on the multifunction
display, accompa
nied by an audible signal.
It is essential to top up the oil to the
correct level, otherwise the engine
may be damaged.
Oil gauge fault
Flashing of the seg
ments indicates a
fault.
Check the level
using the dipstick.
Consult a PEUGEOT dealer. Control module display
After switching on the ignition, three
functions are shown in succession:
– service indicator (see correspond ing section),
– engine oil level indicator,
– total distance recorder (total and trip distances).
Note: the total and trip distances are
displayed for thirty seconds, when
the ignition is switched off, on open
ing the driver's door as well as on
locking and unlocking the vehicle.
It also displays the automatic gear
box positions and programmes
selected (see corresponding sec
tion).
Engine oil level
When the ignition is switched on, the
engine oil level is indicated for
approximately 10 seconds, after the
service information. Lighting rheostat
With the lights on,
press the button to
vary the intensity of
the lighting of the
control module, the
instrument panel, the
air conditioning dis
play and the multi–function display.
When the lighting reaches the mini
mum (or maximum) setting, release
it then press again to increase (or
reduce) the brightness.
As soon as the lighting is of the
brightness required, release the
button.
Trip recorder
zero reset
With the ignition on,
press the button.
INSTRUMENTS AND CONTROLS
34
18-11-2002

Page:   1-10 11-20 21-30 31-40 41-50 ... 80 next >