sensor PEUGEOT 807 2002 Owners Manual

18-11-2002
14 Windscreen washwipe
stalk.
Trip computer stalk.
15 Audio remote control stalk.
16 Interior alarm disarming
switch.
17 Electric mirror controls.
Window controls.
Rear window locking control.
18 Steering lock and ignition.
19 Dynamic stability control
(ESP/ASR) switch.
20 Headlamp height
adjustment.
21 Fuse box.
22 Handbrake.
23 Steering wheel adjustment
control.
24 Battery / Fuse box.
25 Heated seat switches.
26 Storage. 27
Gear lever.
28 Cooled compartment.
29 Ashtray / Can holder.
30 Storage compartment
or remote control keypad.
31 Lighter / 12 V accessories
socket.
32 Hazard warning lights
switch.
33 Air conditioning controls.
34 Passenger compartment
temperature sensor.
35 Passenger lower glove box.
36 Passenger air bag.
37 Side vent.
38 Bonnet release.
39 Passenger air bag disarming
switch*.
* According to country.
YOUR 807 AT A GLANCE3
1 Side window demisting
vents.
2 Speaker (tweeter).
3 Windscreen demisting
vents.
4 Passenger upper glove box.
5 Brightness sensor.
6 Instrument panel /
Multifunction display.
7 RB3, RD3, RT3 audio
equipment with flap.
8 Central vents.
9 Driver’s upper glove box.
10 Lights and direction
indicators stalk.
11 Cruise control controls.
12 Check unit.
13 Driver’s air bag.
Horn.

YOUR 807 AT A GLANCE10STEERING WHEEL STALKS
LIGHTING
Front and rear lights (ring A)Lights off.
Side lights on.Dipped / main
beam headlamps
on.
Automatic
switching on of
lights. Automatic switching on of
lights
To activate or disarm this func
tion, place the key in the acces
sories position, the lighting stalk
in position
0 and press for more
than two seconds on the end of
the stalk.
Front fog lamps and rear fog
lamps (ring B)
Front fog lamps (1 st
rota
tion of the ring forwards).
Front fog lamps
and rear fog
lamps (2 nd
rotation
of the ring for
wards).
To switch off: rotate the push ring
B rearwards. WINDSCREEN WIPERS
Front
2 Rapid wipe
1 Normal wipe
l Intermittent wipe
or
AUTO Automatic wipe
0 Stop
Single wipe
Washwipe: pull the stalk towards you.
Automatic wipe
In the AUTO position, a
rain sensor controls the
automatic operation of
the wipers. The wipers
adapt their speed to
the intensity of the
rainfall.
Rear
Stop Intermittent W ash
wipe wipe
11 2
11 4
18-11-2002

18-11-2002
YOUR 807 AT A GLANCE14REAR PARKING
ASSISTANCE
This system, installed in the rear
bumper, detects any obstacle
(person, vehicle, tree, barrier,
kerb, ...) behind the vehicle.
Switching on
With the engine running, the sys
tem is activated when reverse
gear is engaged. A bleep indi
cates that it is active.
The proximity information is
given by an audible signal, con
sisting of bleeps which becomes
more rapid as the vehicle
approaches the obstacle.
When the distance between the
rear of the vehicle and the obsta
cle is less than approximately
twentyfive centimetres, the audi
ble signal becomes continuous. ➜When you change to
neutral, the system
becomes inactive
again. TYRE UNDERINFLATION
DETECTION
Sensors check the pressure of
the tyres while driving and trigger
a warning in the event of a mal
function (speed above 15 mph
[25 km/h]).
Tyre(s) underinflated
When this message appears on
the multi–function display, accom
panied by an audible signal, have
the pressure of the tyres checked
as soon as possible.
Tyre(s) punctured
The appearance of this message,
accompanied by an audible sig
nal, is followed by illumination of
the
STOP warning light.
Stop immediately, avoiding any
sharp action on the steering
wheel or the brakes.
Change the damaged (punctured
or significantly underinflated)
wheel and have the pressure of
the tyres checked as soon as
possible.
Note: if the damaged wheel is
stored in the boot temporarily, it
will transmit this message again
as a reminder that it must be
repaired, which will prevent
another warning of the same type
being displayed.
The spare wheel does not have a
sensor. X type pressure sensor(s)
missing
The appearance of this message,
accompanied by an audible
warning, indicates that one wheel
(or more) is no longer detected.
Consult a PEUGEOT dealer to
have the faulty sensor(s)
replaced.
Warning:
this message is also
displayed when one of the
wheels is removed from the vehi
cle (for repair) or when a wheel is
fitted which is not equipped with
a sensor (winter tyres).
This system does not eliminate
the need to have the pressure
of the tyres checked regularly.
131141

PEUGEOT SERVICING23
Zero reset Y our PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the reset procedure is as
follows:
 Switch off the ignition,
 Press and hold the trip recorder
reset button,
 Switch on the ignition.
The display begins a countdown.
When the display shows "=0", relea
se the button; the service symbol
disappears.
Important: after this operation, if
you wish to disconnect the battery,
lock the vehicle and wait for at least
five minutes, otherwise the zero re
set will not be registered.
MAINTENANCE OF PARTS SUBJECT TO WEAR AND A CHECK OF
CONSUMABLES
Certain essential components on your vehicle are subject to checks a t specific
frequencies.
• The brake fluid is to be replaced at a maximum of every 36,000/40,000 miles
(60 000km) or every two years;
• The pollen filter must be checked at each serviceby a PEUGEOT dealer
(services and intermediate visits) or more often, depending on the environ
ment (dust, pollution, etc.);
• For HDI turbo diesel engines with particulate emission filter , maintenance
of the filterand topping up of the additive reservoirmust be carried out at a
maximum of every 48,000 miles (80 000 km) by a PEUGEOT dealer;
• Replacement of the timing belt: contact a PEUGEOT dealer.
• Air bags and pretensioning parts on seat belts must be checked every
10 years.
• Tyre pressure sensors are to be replaced every 10 years.
• The check on tyre inflation presure must be carried out cold at least once a
month.
Note: the engine coolant does not have to be replaced.
18-11-2002

The driver and front passenger can
each adjust the air temperature to
suit their requirements.
They can also activate or disarm the
rear ventilation adjustment controls.
Do not cover the passenger com
partment temperature sensor,
located on the right upright of the
centre console. It helps to regu
late the air conditioning.1 Air conditioning on/off  Pressing this button
activates the automatic
operation of the air con
ditioning.
The symbol and the indicator light 1
are displayed.  Pressing this button again switches
the air conditioning off.
The symbol and the indicator light 1
go out.
2 Passenger's sideadjustment
3 Driver's side adjustment
The required value is displayed
(from 14 to 28; comfort value = 21;
maximum driver/passenger differ
ence = 5).  Press the corresponding "+" and
"–" buttons to change it.
YOUR 807 IN DETAIL
86
AUTOMATIC AIR CONDITIONING WITH SEPARATE ADJUSTMENTS
Located on the centre console, the control panel is to the
right of the gear lever.
18-11-2002

AUTOMATIC SWITCHING ON
OF LIGHTS
Side lights and dipped beam head
lamps switch on automatically if the
light is poor, or during continuous
operation of the windscreen wipers.
They switch off when the light
becomes bright enough or the wind
screen wipers stop.
Note: In foggy weather, the bright
ness sensor can detect sufficient
light. As a consequence, the lights
will not come on automatically.
This function is active when the
vehicle is supplied to the customer.
To disarm or activate the function :  Start with the key in the acces
sories position (1st notch),
 Place the lights stalk in position 0,
 Press the end of the stalk for more
than two seconds.
Note: after the ignition is switched off
and depending on the brightness,
the lights remain on for approximate
ly 45 seconds or until the vehicle is
locked.
Do not cover the brightness sen
sor located in the centre of the
fascia. It is used for automatic
switching on of the lights. Operating check
Activation
Activation of this function is accom
panied by an audible signal and the
message
"Automatic lighting
active" on the multi–function dis
play .
Disarming
Disarming of the function is accom
panied by an audible signal.
Note: the function is disarmed
temporarily when the driver uses the
manual lighting controls.
YOUR 807 IN DETAIL 113
18-11-2002

YOUR 807 IN DETAIL115
Maintenance position of front
windscreen wiper
This position allows the front wind
screen wiper blades to be removed.
In the minute following switching off
of the ignition, any action on the
stalk positions the wipers against the
windscreen uprights (for Winter
parking, cleaning of the windscreen
or replacing the blades).
To park the wipers after this has
been done, switch on the ignition
and operate the stalk.
Rear windscreen wiper
Turn ring
Ato the first notch.
The wiping speed is
inversely proportional to the
speed of the vehicle.
Automatic rear windscreen wiping
 place the front wipers stalk in a
position other than 0.
 engage reverse gear.
 the rear wiper operates with inter
mittent wiping.
Note: this function cannot be dis
armed if a bicycle carrier is fitted.
Therefore, you must fit a special bicy
cle carrier, approved by PEUGEOT,
or contact a PEUGEOT dealer.
Rear windscreen wash
Turn ring Apast the first
notch: the windscreen wash
then the windscreen wiper
operate for a specified time.
Do not cover the rain
sensor located at the bot
tom centre of the wind
screen.
When using an automatic car
wash, switch off the ignition or
check that the wiper control is not
in the automatic position.
In winter it is advisable to wait for
the windscreen to completely
clear of ice before operating the
automatic wipe. In winter, in the presence
of a considerable
amount of snow or ice,
switch on the rear screen
demister. Once deicing
is complete, remove the snow or
ice which has accumulated on the
rear wiper blade. You can now
operate the rear windscreen
wiper.
Automatic timed windscreen
wipers
The automatically timed wiping is
controlled by a rain sensor fitted on
the windscreen.
In the
AUTO position, the wind
screen wipers operate automatically
and adapt their speed to the inten
sity of the rainfall.
Operating check
Activation
When the function is activated, the
message "Automatic windscreen
wipers activated" appears on the
multi–function display.
18-11-2002

YOUR 807 IN DETAIL131
REAR PARKING ASSISTANCE
This system consists of four proximity
sensors, located in the rear bumper,
and a special speaker fitted in the
fascia.
This detects any obstacle (person,
vehicle, tree, gate, pavement etc.)
behind the vehicle.
Note: this function will be disarmed
automatically when the vehicle is
towing a trailer or when a bicycle
carrier is fitted (vehicle fitted with
towing attachment or bicycle carrier
recommended by PEUGEOT).
In wintry weather, ensure that the
sensors are not covered with frost or
snow.
Deactivation  Change to neutral, the system is
again inactive.
Activation
The system is activated as soon as
reverse gear is engaged; an audible
bleep shows that it is active.
The proximity information is given by
an audible signal, which becomes
more rapid as the vehicle approach
es the obstacle.
When the distance between the rear
of the vehicle and the obstacle is
less than approximately twentyfive
centimetres, the audible signal
becomes continuous.
Detection zone
If there is an operating
fault, the audible signal will
be a short bleep followed
by a long bleep when
changing to reverse gear.
18-11-2002

141
TYRE UNDERINFLATION
DETECTION
Sensors check the tyre pressure
during driving, and trigger a warning
in the event of malfunction (speed
greater than 15mph [25 km/h]).
Flat tyre
When the message "Tyres deflat
ed" appears on the multi–function
display, accompanied by an audible
signal, have the tyre pressure
checked as soon as possible.
Puncture
The message 'Punctured tyre(s)'
appears on the multi–function dis
play, accompanied by an audible sig
nal and followed by illumination of
the "STOP" warning light.
Stop immediately, avoiding any sud
den movement of the steering wheel
and the brakes.
Change the damaged (punctured or
very deflated) tyre, and have the tyre
presure checked as soon as possi
ble.
Note: if the damaged tyre is tem
porarily stored in the boot, it will
again emit this message to remind
you of the necessity of having it
repaired. This will prevent another
warning of the same type being dis
played. Sensor(s) not detected
When the message
"X tyre pres
sure sensor(s) missing" appears
on the multi–function display,
accompanied by an audible signal,
this indicates that underinflation
detection is absent from one (or sev
eral) tyre(s).
Contact a PEUGEOT dealer to
replace the faulty sensor(s).
Note: this message is also displayed
when one of the tyres is away from
the vehicle (being repaired) or when
a wheel without a sensor is fitted.
PRACTICAL INFORMATION
All repairs and changing
of tyres on a wheel fitted
with this system must be
carried out by a
PEUGEOT dealer.
The tyre underinflation detec
tion system is a driving aid
which does not take the place
of vigilance or the responsibili
ty of the driver.
This system does not remove the
need to have the tyre pressure
checked regularly (including the
spare wheel), to ensure that the
dynamic performance of the vehi
cle remains at its best and to
avoid premature wear of the tyres,
in particular in the case of arduous
driving (heavy load, high speed).
The system may temporarily be
disturbed by radio broadcasts on
a frequency close to it.
18-11-2002

PRACTICAL INFORMATION151
Fuse N° Rating
Functions
1 10 A Manual gearbox reversing lights switch Xenon headlamps Fan uni t relay control
Engine coolant level Oil heater or preheat unit (Diesel) V ehicle speed sensor or air flow
sensor (Diesel).
2 15 A Fuel pump Exhaust gas recirculation and Turbo pressure regulation solenoid valves
(Diesel).
3 10 A ABS or ESP control unit.
4 10 A Engine wiring housing ignition positive supply
5 10 A Not used or particle emission filter injector (Diesel) Particle emi ssion filter control unit (Diesel).
6 15 A Front fog lamps.
7 20 A Headlamp wash pump.
8 20 A Supply via the engine wiring housing relay Fan unit relay co ntrol (Diesel) –
Diesel high pressure regulation and exhaust gas recirculation sol enoid valves
(Diesel).
9 15 A Left dipped beam Headlamp height adjuster.
10 15 A Right dipped beam.
11 10 A Left main beam.
12 10 A Right main beam.
13 15 A Horn.
14 10 A Front and rear washwipe pump.
15 30 A Oxygen sensor Injectors Ignition coil Canister, timing and exhaust gas recriculation
solenoid valves (Petrol) Injection pump solenoid valve (Diesel).
16 30 A Not used or air pump (Petrol).
17 30 A Front wiper.
18 40 A Additional blowers.
18-11-2002