PEUGEOT 807 2004.5 Owner's Manual

Instruments and controls24 -
30-08-2004
25Instruments and controls-
30-08-2004
Service indicator
Located in the instrument panel with
the total distance recorder (total and
trip distances), this programs service
intervals according to the use of the
vehicle.The service is overdue
*.
Each time the ignition is switched on
and for a few seconds, the spanner
lashes and the excess distance is
displayed.
A few seconds after the ignition is
switched on, the oil level is displayed,
then the total distance recorder
resumes normal operation showing
the total and trip distances.
The distance remaining before the
next service is less than 1 000 km.
Each time the ignition is switched on
and for a few seconds, the spanner
lashes and the number of kilometres
remaining is displayed:
A few seconds after the ignition is
switched on, the oil level is displayed,
then the total distance recorder resumes
normal operation and the spanner re-
mains lit. This indicates that a service
should be carried out shortly.
Note:
with the engine running the
spanner remains lit until the service
has been carried out.
* First of the two terms reached: the spanner also lights up if the two-
year interval has elapsed.
Operation
A few moments after the ignition
has been switched on, the spanner
indicating a service operation lights
up; the display for the total distance
recorder tells you (in round igures)
the distance remaining before the
next service.
The points at which a service is due
are calculated from the last indicator
zero reset.
The point at which a service is due is
determined by two parameters:
- the distance travelled.
- the time which has elapsed since
the last service.
Note: the distance remaining before
the next service may be weighted
by the time factor, depending on the
driver's driving habits.
Example: 4 800 km remain before
the next service is due. When the
ignition is switched on and for a few
seconds, the display shows:

Instruments and controls26 -
30-08-2004
MaximumWith the ignition on,
press the button until
the zeros appear.
Zero re-set
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows: F
Switch off the ignition,
F Press and hold the trip recorder
re-set button,
F Switch on the ignition.
The display begins a countdown.
When the display shows "= 0", release
the button; the spanner disappears.
Note: after this operation, if you
wish to disconnect the battery, lock
the vehicle and wait for at least
ive minutes, otherwise the zero
reset will not be registered. With the lights on,
press the button to
vary the intensity of the
lighting of the instru-
ments and controls.
When the lighting
reaches the minimum
(or maximum) setting,
release the button then press it again
to increase (or reduce) the brightness.
As soon as the lighting is of the re-
quired brightness, release the button.
Minimum
Check the level using
the dipstick and top
it up.
Lack of oil
The message
"Top
up engine oil level"
appears on the multi-
function display, accompanied by an
audible signal.
It is essential that the level is topped
up. There is a risk of damage to the
engine.
Oil level gauge fault
Never exceed the maximum
level as a surplus of oil may
damage the engine.
Contact a PEUGEOT dealer
without delay.
Engine oil level indicator
When the ignition is switched on,
the engine oil level is indicated for
approximately 10 seconds, after the
service information.
The indication is only correct if the
vehicle is on level ground and the
engine has been off for more than
15 minutes. Flashing of the seg-
ments indicates a mal-
function.
Check the level using
the dipstick.
Contact a PEUGEOT dealer.
Trip recorder zero reset button
Lighting rheostat

27Audio - Telematics-
30-08-2004
MULTI-FUNCTION SCREENS
Presentation
Monochrome screen B
This enables the following informa-
tion to be displayed:
- the time,
- the date,- the outside temperature (this lashes
when there is a risk of ice),
- the radio displays, - the status of the openings (doors,
bonnet...),
- the warning messages (e.g. "Bat-
tery charge fault") or information
messages (e.g. "Passenger air bag
deactivated") displayed temporarily
can be cleared by pressing button
1 or 2,
- the trip computer (see correspon-
ding section). Monochrome screen CT and
colour screen DT
These two systems are controlled
by the
RT3 GPS audio/telephone
keypad and/or by an additional
telematics control.
They enable the following information
to be displayed:
- the time,
- the date,
- the outside temperature (a message warns you when there is a risk of
ice),
- the audio source displays (radio, CD, ...),
- the telematic system displays (tele- phone, services, ...),
- the status of the openings (doors, bonnet, ...),
- the warning messages (e.g. "Fuel level low") and vehicle functions
status messages (e.g. "Passenger
air bag deactivated"), displayed
temporarily,
- the trip computer display (see cor- responding section),
- the satellite navigation system dis- plays (see corresponding section).
Note: to enable you to use all of
your system's functions, you have
two CD ROMs: one, "Coniguration",
contains the software and the va-
rious display and spoken information
languages, the other, "Navigation",
contains the satellite navigation sys-
tem map data. Monochrome screen CT
General menu
Press the
"MENU" button to access
the general menu and select one of
the following applications:
- navigation - guidance (see section "Satellite navigation system"),
- audio functions (see "RT3 audio/ telephone" section),
- trip computer (see corresponding section),
- directory (see "RT3 audio/ telephone" section),
- telematics (see "RT3 audio/ telephone" section),
- coniguration (see corresponding section).

Audio - Telematics28 -
30-08-2004
29Audio - Telematics-
30-08-2004
Monochrome screen B
Press button 1 for two seconds to
gain access to the settings .
Then, each press of this button per-
mits scrolling of the various param-
eters. - language of the information dis-
played,
- unit of speed (km or miles),
- unit of temperature (degrees Cel-
sius or Fahrenheit),
- time format (12 or 24 hours),
- hour,
- minute,
- year,
- month,
- day.
Pressing button 2 enables you to
change the parameter selected.
Continue pressing the button for
rapid scrolling.
After seven seconds without action,
the screen returns to the usual dis-
play, the modiied data are recorded.
Parameter coniguration
Colour screen DT
General menu -
telematics (see "RT3 audio/telephone"
section),
- coniguration (see corresponding
section),
- map (see section "Satellite naviga- tion system"),
- video (see corresponding section).
Press the "MENU" button to access
the general menu and select one of
the following applications:
- navigation - guidance (see section "Satellite navigation system"),
- audio functions (see "RT3 audio/ telephone" section),
- trip computer (see corresponding section),
- directory (see "RT3 audio/telephone" section),
A few definitions...
Superimposed display:
a window appears over the current
application for a short while, to an-
nounce a change of status of another
application.
Permanent application:
main application currently in use, dis-
played in the main screen window.
Contextual menu:
limited menu associated with the
main application currently in use, dis-
played in the main screen window.

Audio - Telematics28 -
30-08-2004
29Audio - Telematics-
30-08-2004
Monochrome screen B
Press button 1 for two seconds to
gain access to the settings .
Then, each press of this button per-
mits scrolling of the various param-
eters. - language of the information dis-
played,
- unit of speed (km or miles),
- unit of temperature (degrees Cel-
sius or Fahrenheit),
- time format (12 or 24 hours),
- hour,
- minute,
- year,
- month,
- day.
Pressing button 2 enables you to
change the parameter selected.
Continue pressing the button for
rapid scrolling.
After seven seconds without action,
the screen returns to the usual dis-
play, the modiied data are recorded.
Parameter coniguration
Colour screen DT
General menu -
telematics (see "RT3 audio/telephone"
section),
- coniguration (see corresponding
section),
- map (see section "Satellite naviga- tion system"),
- video (see corresponding section).
Press the "MENU" button to access
the general menu and select one of
the following applications:
- navigation - guidance (see section "Satellite navigation system"),
- audio functions (see "RT3 audio/ telephone" section),
- trip computer (see corresponding section),
- directory (see "RT3 audio/telephone" section),
A few definitions...
Superimposed display:
a window appears over the current
application for a short while, to an-
nounce a change of status of another
application.
Permanent application:
main application currently in use, dis-
played in the main screen window.
Contextual menu:
limited menu associated with the
main application currently in use, dis-
played in the main screen window.

Audio - Telematics28 -
30-08-2004
29Audio - Telematics-
30-08-2004
CT monochrome screen
The "Display Coniguration" menu
gives access to the following param-
eters:
• "Adjust the brightness": display brightness setting,
• "Sound": voice synthesiser setting (for the masculine/feminine voice
parameter: insert the coniguration
CD-Rom); setting of the spoken
commands,
• "International parameters": date and time setting (12 or 24 hour
mode, adjustment of the minutes
on GPS); units setting (l/100 - °C or
mpg - °F),
• "Choice of language": selection of the language for the display, infor-
mation and voice commands (Ger-
man, English, Spanish, French,
Italian, Dutch, Portuguese: insert
the coniguration CD ROM). DT colour screen
The
"Coniguration" menu gives
access to the following parameters:
• "Choose colours": selection from the palette of colours available for
display,
• "Luminosity and brightness": dis- play brightness setting,
• "Sound": voice synthesiser setting (for the masculine/feminine voice
parameter: insert the coniguration
CD-Rom); setting of the spoken
commands,
• "International parameters": date and time setting (12 or 24 hour
mode, adjustment of the minutes
on GPS); units setting (l/100 - °C or
mpg - °F),
• "Choice of language": selection of the language for the display, infor-
mation and voice commands (Ger-
man, English, Spanish, French,
Italian, Dutch, Portuguese: insert
the coniguration CD ROM). Video on the DT screen
It is possible to connect video equip-
ment (a camcorder, digital camera, ...)
using the three video sockets situated
inside the glove box.
It is only possible to display video
images when the vehicle is sta-
tionary.
Select the
"Video" menu from the
main menu :
- "Activate video mode" to activate/ cancel the video function,
- "Video parameters" to adjust the display format, the brightness, con-
trast and colour.
Press "MODE" or "DARK" to exit
video mode.
Successive presses on the
"SOURCE" button allow you to se-
lect another audio source other than
the video.
For safety reasons, con-
iguration of the multi-func-
tion screens by the driver
must be carried out when
stationary.

Audio - Telematics30 -
30-08-2004
31Audio - Telematics-
30-08-2004
The additional telematics
control
This permits selection and valida-
tion of the functions, commands and
parameters, displayed on the CT
monochrome screen and the DT
colour screen .
It is located next to the gear lever. Rotation of the knob:
This enables you to
move around
the screen and thus select a func-
tion.
It also permits:
- with a "setting" type parameter,
following selection, increasing or
decreasing of the value,
- with a "list" type parameter, after
opening the list, scrolling of the
values,
- with guidance on a map, increasing
or decreasing of the zoom factor. "ESC" button:
- Brief press:
cancellation of the
operation in progress or clearing
of the last superimposed display.
- Pressing for more than two se- conds: clearing of all of the super-
imposed displays and return to the
permanent application.
Pressing the knob:
This permits:
- access to the list of commands
(context-related menu) of the per-
manent application displayed, if no
superimposed display appears,
- validation of the selected function
or of the modiied value,
- selection of a "setting" or "list"
type parameter in order to modify it.
"MODE" button:
- Brief press: modiication of the per- manent application display (audio
equipment, navigation/guidance, ...),
- Pressing for more than two se- conds: displaying of the general
information . "MENU" button:
- Brief press: access to the
general
menu .
- Pressing for more than two se- conds: access to the help menu.
"MUSIC" button:
- Brief press: displaying of the con- text-related menu of the active
audio source (tuner, CD, ...).
"TEL" button:
- Brief press: opening of the line, in the case of an in-coming call, or
displaying of a telephone source
context-related menu.
"NAV" button:
- Brief press: displaying of a context- related menu of the navigation/
guidance function.
"MAIN" button:
- Brief press: displaying of the gene-
ral information .

Audio - Telematics32 -
30-08-2004
33Audio - Telematics-
30-08-2004
ButtonFunction
A Radio on/off
B - Reduction in volume
C + Increase in volume
D
5Ejection of CD
E RDS RDS function on/off
Press for more than 2 seconds: regional following mode on/off
AUDIO RD3

Audio - Telematics32 -
30-08-2004
33Audio - Telematics-
30-08-2004
ButtonFunction
F TA Trafic information priority on/off
Press for more than 2 seconds: PTY function on/off
G
¯Selection of bass, treble, loudness, sound distribution and a utomatic volume correction
H
5Increase of the functions associated with button G
I
6Decrease of the functions associated with button G
J
8Manual or automatic search of higher frequency
Selection of next CD track
K MAN Manual/automatic operation of buttons J and L
L
7Manual or automatic search of lower frequency
Selection of previous CD track
M CH. CD Selection of CD changer
Press for more than 2 seconds: shufle
N CD Selection of the CD source
Press for more than 2 seconds: shufle
O Radio Selection of the radio source. Selection of wavebands FM1, FM2,
FMAST, AM
Press for more than 2 seconds: automatic storing of stations (autosto re)
1 to 6 1 2 3 4 5 6 Selection of station stored in memory - Selection of the CDs in
the CD changer
Press for more than 2 seconds: storing of a station in memory

Audio - Telematics34 -
30-08-2004
35Audio - Telematics-
30-08-2004
GENERAL FUNCTIONS
On/off
With the ignition key
in the accessories or
ignition position, press
button A to switch the
set on or off.
The set can operate
for 30 minutes without the vehicle
ignition being switched on.
ADJUSTING THE VOLUME
Press button C to increase the vol-
ume, or button B to decrease it.
Continuous pressure on buttons B
and C allows a gradual adjustment
of the volume.
AUDIO SETTINGS
Press button G sev-
eral times in succes-
sion to access the bass ( BASS) , treble (TREB) ,
loudness (LOUD), fader
(FAD), balance ( BAL)
and automatic volume
correction settings.
Exit from audio mode is automatic
after a few seconds without pressing
any button, or by pressing button G
after coniguration of the automatic
volume correction.
Note: bass and treble settings are
speciic to each source. It is possible
to set them differently for radio, CD
or CD changer. When
"BASS" is
displayed, press but-
ton H or I to vary the
setting.
- "BASS -9" for a
minimum bass set-
ting,
- "BASS 0" for a nor-
mal setting,
- "BASS +9" for a maximum bass
setting.
Adjusting the bass
Anti-theft system
The audio system is coded in such a
way that it can operate only on your
vehicle. It would not function if itted
to another vehicle.
The anti-theft system is automatic
and requires no action on your
part. Adjusting the treble
When
"TREB" is displayed, press
button H or I to vary the setting.
- "TREB -9" for a minimum treble
setting,
- "TREB 0" for a normal setting,
- "TREB +9" for a maximum treble
setting.
Adjusting the loudness
This function automatically empha-
sises bass and treble tones.
Press button H or I to switch the func-
tion on or off.