PEUGEOT 807 2004.5 Owner's Guide

Audio - Telematics34 -
30-08-2004
35Audio - Telematics-
30-08-2004
Adjusting the front/rear sound
distribution (Fader)
When "FAD" is displayed, press but-
ton H or I.
Button H increases the volume at
the front.
Button I increases the volume at the
rear.RADIO
Notes on radio reception
Your car radio is subject to phenom-
ena which do not affect domestic
radio sets. Both AM (MW/LW) and
FM reception are subject to various
forms of interference. This is no re-
lection on the quality of the equip-
ment, but is due to the nature of the
signals and the way in which they are
transmitted.
On MW/LW, interference may be
noticed when passing under high
voltage power lines or bridges, or in
tunnels.
On FM, interference may be the re-
sult of increasing distance from the
transmitter, delection of the signals
by obstacles (mountains, hills, build-
ings, etc.), or of being in an area
which is not covered by a transmit-
ter.
Press button O.
Selecting radio mode Press button
O briely to select wave-
bands FM1, FM2, FMast and AM.
Selecting a waveband
Briely press button
J or L to search
for the station immediately above or
below. By continuing to press the
button in the direction selected, you
will obtain continuous scrolling of the
frequency.
The scrolling stops at the irst sta-
tion found as soon as the button is
released.
If the TA trafic program is selected,
only stations broadcasting this type
of program are selected.
Searching for a station occurs irst
in "LO" sensitivity (selection of the
most powerful transmitters) during
scanning of the waveband, then in
"DX" sensitivity (selection of the
weakest and most distant transmit-
ters).
To make a direct search in "DX" sen-
sitivity, press button J or L twice.
Automatic station search
Adjusting the right/left sound
distribution (Balance)
When "BAL" is displayed, press but-
ton H or I.
Button H increases the volume on
the right-hand side.
Button I increases the volume on the
left-hand side.
Automatic volume correction
This function enables the volume to
be automatically adjusted depending
on the level of noise produced by the
speed of the vehicle.
Press buttons H or I to switch the
function on or off.

Audio - Telematics34 -
30-08-2004
35Audio - Telematics-
30-08-2004
Adjusting the front/rear sound
distribution (Fader)
When "FAD" is displayed, press but-
ton H or I.
Button H increases the volume at
the front.
Button I increases the volume at the
rear.RADIO
Notes on radio reception
Your car radio is subject to phenom-
ena which do not affect domestic
radio sets. Both AM (MW/LW) and
FM reception are subject to various
forms of interference. This is no re-
lection on the quality of the equip-
ment, but is due to the nature of the
signals and the way in which they are
transmitted.
On MW/LW, interference may be
noticed when passing under high
voltage power lines or bridges, or in
tunnels.
On FM, interference may be the re-
sult of increasing distance from the
transmitter, delection of the signals
by obstacles (mountains, hills, build-
ings, etc.), or of being in an area
which is not covered by a transmit-
ter.
Press button O.
Selecting radio mode Press button
O briely to select wave-
bands FM1, FM2, FMast and AM.
Selecting a waveband
Briely press button
J or L to search
for the station immediately above or
below. By continuing to press the
button in the direction selected, you
will obtain continuous scrolling of the
frequency.
The scrolling stops at the irst sta-
tion found as soon as the button is
released.
If the TA trafic program is selected,
only stations broadcasting this type
of program are selected.
Searching for a station occurs irst
in "LO" sensitivity (selection of the
most powerful transmitters) during
scanning of the waveband, then in
"DX" sensitivity (selection of the
weakest and most distant transmit-
ters).
To make a direct search in "DX" sen-
sitivity, press button J or L twice.
Automatic station search
Adjusting the right/left sound
distribution (Balance)
When "BAL" is displayed, press but-
ton H or I.
Button H increases the volume on
the right-hand side.
Button I increases the volume on the
left-hand side.
Automatic volume correction
This function enables the volume to
be automatically adjusted depending
on the level of noise produced by the
speed of the vehicle.
Press buttons H or I to switch the
function on or off.

Audio - Telematics36 -
30-08-2004
37Audio - Telematics-
30-08-2004
Press the "MAN" button.
Briely press button J or L to in-
crease or decrease the frequency
displayed.
By continuing to press the button
in the direction selected, you will
obtain continuous scrolling of the
frequency.
The scrolling stops at the irst sta-
tion found as soon as the button is
released.
Pressing the "MAN" button again re-
turns you to automatic station search. Select the station required.
Press one of the buttons
"1" to "6"
for more than two seconds.
The sound stops then becomes audi-
ble again, conirming that the station
has been stored in the memory.
Manual storing of stations in the
memory
Automatic storing of FM stations
in the memory (autostore)
Press button O down
for more than two
seconds.
Your radio automati-
cally stores the six stations with the
strongest signal in FM. These sta-
tions are stored in the FMast wave-
band.
If it is not possible to ind 6 stations,
the remaining memories are empty.
RDS
Using the RDS (Radio Data
System) function on FM
The Radio Data System allows you
to continue listening to the same sta-
tion whatever frequency it is using for
the region you are going through.
RDS station following
The display indicates the name of the
station selected. The radio is contin-
ually searching for the station which
has the best reception and which is
transmitting the same program.
Manual station search
Recalling stations stored in the
memory
For each waveband, briely press
one of the buttons "1" to "6" to recall
the corresponding station. Briely press the
"RDS"
button to
switch the function on
or off.
The multifunction dis-
play will show:
- "RDS" if the function is selected,
- "(RDS)" if the function is selected
but not available.

Audio - Telematics36 -
30-08-2004
37Audio - Telematics-
30-08-2004
Press the "TA" button
to switch the function
on or off.
The multifunction display will show:
- "TA" if the function is selected,
- "(TA)" if the function is selected but
not available.
Any trafic information lash will be
given priority, whatever source you
are listening to (radio, CD or CD
changer).
If you wish to interrupt a message,
press the "TA" button; this switches
the function off.
Note: the volume of trafic infor-
mation announcements is inde-
pendent of the volume of normal
radio listening. You can adjust
it using the volume button. The
setting will be stored and will be
used when the next messages are
broadcast.
Trafic information program
PTY function
This allows you to listen to stations
broadcasting a speciic type of program
(news, culture, sport, rock, etc.).
Regional following mode (REG)
When they are part of a network,
certain stations broadcast regional
programs in the various areas they
serve. With regional following mode
you can keep listening to the same
program.
Press the "RDS" button for more
than two seconds to switch the func-
tion on or off. - select the
PTY function,
- briely press button J or L to scroll
down the list of the various types of
programs offered,
- when the program of your choice is displayed, keep button J or L
pressed for more than two seconds
to carry out an automatic search
(after an automatic search the PTY
function is switched off).
In PTY mode, the different types of
programs can be stored in memory.
To do this, press the preselection
buttons "1" to "6" for more than two
seconds. Briely press the corre-
sponding button to recall the type of
program stored in the memory.
With FM selected,
press the "TA" but-
ton for more than two
seconds to switch this
function on or off. To search for a
PTY program:
EON system
This connects stations which are part
of the same network. It enables the
broadcasting of trafic information or
a PTY program by a station that is
part of the same network as the sta-
tion to which you are listening.
This service is available when you
have selected the TA trafic informa-
tion program or the PTY function.

Audio - Telematics38 -
30-08-2004
39Audio - Telematics-
30-08-2004
After insertion of a
disc, printed face
upwards, the player
starts automatically.
If a disc is already inserted, press
button N.
COMPACT DISC
Selecting CD mode
Press button D to
eject the disc from the
player.
Ejection of a disc
Press button
J to select the next
track.
Press button L to return to the start
of the current track or to select the
previous track.
Selecting a track Accelerated play
Keep button
J or L pressed for for-
wards or backwards accelerated
play.
Accelerated play stops as soon as
the button is released.
Shufle
When the CD player is selected,
keep button N pressed for two sec-
onds. The tracks will be played in
random sequence. Pressing the
button again for two seconds returns
you to normal play.
Shufle mode is de-activated each
time the audio equipment is switched
off.
The use of copied compact
discs may cause malfunc-
tions.
Insert circular compact
discs only.

Audio - Telematics38 -
30-08-2004
39Audio - Telematics-
30-08-2004
Press button M.
CD CHANGER
Selecting CD changer mode
The use of copied compact
discs may cause malfunc-
tions.
Insert circular compact
discs only.
Press button
J to select the next
track.
Press button L to return to the start
of the current track or to select the
previous track.
Selecting a track
Selecting a disc
Press one of the buttons
"1" to "6"
on the radio to select the correspon-
ding disc. Accelerated play
Keep button J
or L pressed for
forwards or backwards accelerated
play.
Accelerated play stops as soon as
the button is released.
Shufle
When the CD changer is selected,
keep button M pressed down for two
seconds. The tracks will be played
in random sequence. Pressing the
button again for two seconds returns
you to normal play.

Audio - Telematics40 -
30-08-2004
41Audio - Telematics-
30-08-2004
RT3 GPS AUDIO/TELEPHONE
ButtonFunction
A Press: audio/telephone on/off.
Rotation: volume adjustment.
B
5Ejection of CD.
C SOURCE Selection of source: radio, CD, CD changer or Aux.
D Call connect (Tel/Incoming call) - Display contextual menu (Tel/N ot engaged).
E Access "PEUGEOT" services menu.
Press for between 2 and 8 seconds: call "PEUGEOT Assistance" direct.
Press for more than 8 seconds: cancellation of the call made.

Audio - Telematics42 -
30-08-2004
43Audio - Telematics-
30-08-2004
ButtonFunction
F MODE Change display.
Press for more than 2 seconds: display general information.
G Press: display contextual menu of display - Conirm inputting or ad
justment.
Rotation: move within a menu - Select function/parameter - Audi o settings:
sound ambience, bass, treble, loudness, fader (front/rear balance ), balance (left/right balance),
automatic volume.
H
5Adjust higher frequency, step by step or continuous (long press).
Select previous CD (CD changer) - Movement on map (navigation).
I
6Adjust lower frequency, step by step or continuous (long press).
Select following CD (CD changer) - Movement on map (navigation).
J Infra-red window (IrDA)*.
K ESC Cancel current operation.
Press for more than 2 seconds: clear all superimposed displays and retu
rn to
permanent application.
L SIM card cover.
M
8
Automatic search of higher frequency - Selection of following CD track.
Movement on map (navigation).
Double press: change from LO mode to DX mode.
Press for more than 2 seconds: CD accelerated forwards play.
N
7
Automatic search of lower frequency - Selection of previous CD track.
Movement on map (navigation).
Double press: change from LO mode to DX mode.
Press for more than 2 seconds: CD accelerated backwards play.

Audio - Telematics42 -
30-08-2004
43Audio - Telematics-
30-08-2004
ButtonFunction
O DARK 1st press: display top band (remainder of screen is black) - 2nd press:
brightness removed (black
screen) - 3rd press: return to normal screen.
Press for more than 10 seconds: reinitialisation of the system.
P MENU Display general menu - Press for more than 2 seconds: display help scre
en and list of voice
commands.
Q Disconnect.
Press for more than 2 seconds: activation/deactivation of the tran
sfer of the call to the voice mail or
to a call diversion number.
R BAND
AST Select FM1, FM2, FMast, AM wavebands.
Press for more than 2 seconds: automatic storing of stations (autosto
re).
S TA/PTY Trafic information priority on/off.
Press for more than 2 seconds: PTY function on/off.
T RDS RDS function on/off.
Press for more than 2 seconds: regional following mode on/off.
U AUDIO Display window for adjusting the sound ambience, bass, treble
, loudness, sound distribution and
automatic volume correction.
V SOS Press between 2 and 8 seconds: emergency call.
Press for more than 8 seconds: cancellation of the call made.
1 to 6 1 2 3 4 5 6 Select station in memory - Select CD in the CD changer.
Press more than 2 seconds: store station in memory while listening.
0 to 9 * # 0 1 2 3 4 5
6 7 8 9 * # Alphanumeric keypad for entering descriptions and telephone numb
ers.
* During the year.

Audio - Telematics44 -
30-08-2004
45Audio - Telematics-
30-08-2004
With the ignition
switch in the acces-
sories position or with
the ignition on, press
button A to switch
the audio function of
the RT3 GPS audio/
telephone on or off.
GENERAL FUNCTIONS
On/off
Note: in the absence of an ignition
key, press button A to switch the
telematics system on or off.
The RT3 GPS audio/telephone can
operate for 30 minutes without
switching the vehicle ignition on. Anti-theft system
The RT3 GPS audio/telephone is
coded in such a way that it can op-
erate only on your vehicle. If itting
it to another vehicle, consult your
PEUGEOT dealer for coniguration
of the system.
The system is automatic and re-
quires no action on your part.Press button
U to ac-
cess Sound ambience,
Bass , Treble , Loud-
ness , Fader (front/rear
balance), Balance (left/
right balance) and Au-
tomatic volume adjustment settings.
Exit from audio mode is automatic af-
ter a few seconds without any action,
or by pressing the "ESC" button.
Note: bass, treble and loudness set-
tings are speciic to each source. It is
possible to have different settings for
radio, CD or CD changer.
AUDIO SETTINGS
Notes:
- the SIM card must be removed only after the audio/telephone has been
switched off,
- following automatic switching off of the audio/telephone after 30 minutes,
it is possible to make a telephone call
by pressing button D,
- after the ignition has been switched off, the audio/telephone can be
switched on again by pressing but-
tons D, E, V or by inserting a CD in
the player.
ADJUSTING THE VOLUME
Turn button A clockwise to increase
the volume of the audio/telephone or
anti-clockwise to decrease it.
Note: the volume setting is speciic
to each source. It is possible to have
different settings for radio, CD or CD
changer.