PEUGEOT 807 2004.5 Manual PDF

Seats, bench seats76 -
30-08-2004
77Seats, bench seats-
30-08-2004
THE SEATS
Front seats with manual
adjustment
1 - Forwards/backwards adjustment
Lift the bar and slide the seat for-
wards or backwards.
2 - Seat back angle adjustment
Pull the lever upwards.
3 - Driver's seat height adjustment
Manoeuvre the handle upwards or
downwards until the desired position
is reached.
4 - Driver's seat lumbar adjustment
Move the lever up or down to obtain
the required position.
5 - Head restraint height and angle adjustment
To raise or lower the restraint, pull it
forwards, then slide it.
The adjustment is correct
when the upper edge of the
head restraint is level with the
top of the head.

Seats, bench seats76 -
30-08-2004
77Seats, bench seats-
30-08-2004
To remove it, set it in the high posi-
tion, lift the tab using a coin and pull
upwards and forwards at the same
time.
To re-install, engage the head re-
straint rods in the holes, making sure
they are aligned with the seat back.6 - Rotating of seats
Place the seat back in the upright
position.
Place the seat in the highest interme-
diate longitudinal position.
On the driver's side, push the steer-
ing wheel, apply the handbrake, then
release, pulling on the end.
Pull the control upwards and rotate
the seat inwards.
Never drive with the head
restraints removed; they
must be in place and cor-
rectly adjusted. This pivoting operation must
be carried out with the en-
gine switched off.
The passenger must not be
facing the rear when the ve-
hicle is being driven.

Seats, bench seats78 -
30-08-2004
79Seats, bench seats-
30-08-2004
Front seats with electrical
adjustment
A - Forwards-backwards adjustment
Push the control forwards or back-
wards to slide the seat.
B - Driver's seat height adjustment
Push the rear part of the control up-
wards or downwards to obtain the
required height.
C - Seat back angle adjustment
Tilt the control to the front or the rear
to obtain the correct angle.
Note: the electrical functions of the
seats are cancelled one minute after
the ignition has been switched off.
D - Driver's seat lumbar adjustment (mechanical)
Raise or lower the lever to obtain the
correct position.

Seats, bench seats78 -
30-08-2004
79Seats, bench seats-
30-08-2004
The setting is correct when
the upper edge of the head
restraint is level with the top of
the head.
To remove the head restraint, place it
in the high position, lift the tab using
a coin and pull upwards and forwards
at the same time.
To re-install, engage the head re-
straint rods in the holes, making sure
they are aligned with the seat back.Never drive with the head
restraints removed; they
must be in place and cor-
rectly adjusted. This pivoting operation must
be carried out with the en-
gine switched off.
The passenger must not be
facing the rear when the ve-
hicle is being driven.
F - Rotating of seats (mechanical)
Place the seat back in the upright
position.
Place the seat in the highest interme-
diate longitudinal position.
On the driver's side, push the steer-
ing wheel, apply the handbrake, then
release, pulling on the end.
Pull the control upwards and rotate
the seat inwards.
E - Head restraint height and
angle adjustment
To raise or lower the head restraint,
pull it forwards, then slide it.

Seats, bench seats80 -
30-08-2004
81Seats, bench seats-
30-08-2004
Memorising seat positions
Four driving positions can be memo-
rised:
- two, using two remote control
keys (two users) ,
- two, using buttons M/1 and M/2 .Memorising using the buttons
M,
1 and 2
To memorise using the buttons lo-
cated on the side of the seat:
F Place the ignition key in the 'run-
ning' position (2nd notch),
F Adjust your seat and mirrors,
F Press button M, then button 1
(irst driving position) or button 2
(second driving position) within
four seconds.
An audible signal conirms that a
position has been memorised.
Memorising a new position cancels
the previous one. Front heated seat controls
The front seats can be heated sepa-
rately.
Use the adjustment controls located
on the side of each seat to select the
level of heating required:
0:
Off.
1: Low.
2: Medium.
3: High.
The seat temperature is controlled
automatically.
Note: the heated seats only operate
with the engine running.
Recalling a memorised position
Engine off F
Briely press button 1 or 2 to recall
the corresponding memorised po-
sition.
Note: after recalling a memorised
position ive times in succession, the
function will be cancelled until the
engine is started.
Driving positions memorised by
the remote control key
When locking the doors, the remote
control key memorises the position of
the driver's seat.
When unlocking the doors, the driver's
seat resumes the position memorised
by the remote control key if this has
changed in the meantime.
Each remote control key can
memorise a speciic setting.
Engine running F
Keep button 1 or 2 pressed down
until the end of setting of the cor-
responding memorised position.

Seats, bench seats80 -
30-08-2004
81Seats, bench seats-
30-08-2004
FRONT SEAT LAYOUT
1 - Storage drawers
There is a storage drawer under
each front seat.
- To open it, lift and pull.
- To take it out, open it to its full ex-tent, lift the two tabs on either side
of the drawer, then remove it com-
pletely.
Note: under the front seat on the
passenger side, if the vehicle has an
ampliier, the storage drawer will be
locked. 2 - Elastic retaining straps
There is an elastic retaining strap on
each front seat, on the centre side.
- In the side position (elastic strap on
its own seat), this can be used as a
magazine holder.
- In the transverse position (elastic straps A hooked between the two
seats), they can hold a bag.
3 - 'Aircraft' type table
You have an 'aircraft' type table,
equipped with a can holder, itted to
the rear of each front seat.
Do not forget to fold this before
pivoting the seat.
Note: each front seat also has a stor-
age pocket on the seat back. 4 - 12 V socket
You have a 12 V accessory socket
at the foot of the driver's seat, which
is accessible to passengers in the
2nd
row.
5 - Front and rear armrests
To place the armrest in its rest
position: - Lift the armrest until it is aligned
with the seat back.
To place the armrest in the
position in which it is used: - Push it towards the rear.
- Fold it down completely.
- Raise it slowly to the required posi- tion.
- If you lift it past the required posi- tion, restart the above operations.
To remove it occasionally:
- Lift the armrest, going past the idle position.
- Press its securing pin irmly and tilt it fully.
- Pull towards you to remove it from its ixing.
To put it back in place:
- Place it in its removal position.
- Push as far as the ixing allows.

Seats, bench seats82 -
30-08-2004
83Seats, bench seats-
30-08-2004
THE REAR SEATS
Forwards/backwards adjustment
Lift bar A and slide the seat towards
the front or the rear.
From the third row you can pull on
strap B and slide the seat towards
the front.
This makes it easier for passengers
to exit the 3rd row of seats, when
folding down the second row seat. Folding a side seat
Access to the third row:
Place the head restraint in the low
position.
Push control
C upwards as far as
possible.
Tilt the seat back towards the front
until the rear anchorages are un-
locked.
Fold the seat back onto the seat
cushion.
Place the seat in the closed position. Table position of a side seat
Fold the corresponding seat.
Tilt the folded seat rearwards, until
the rear anchorages lock.
You now have a shelf with two cup
holders.
Adjusting the angle of the seat
back
Push lever C upwards and adjust the
angle as required.
Release the lever to lock. Exiting the third row:
Place the head restraint in the low
position.
Push control
D upwards as far as
possible.
Tilt the seat back towards the front
until the rear anchorages are un-
locked.
Fold the seat back onto the seat
cushion.
Place the seat in the closed position. Folding a side seat from the table
position
Lift the seat back.
Fold as described opposite.

Seats, bench seats82 -
30-08-2004
83Seats, bench seats-
30-08-2004
Table position of the centre seat
Place the head restraint in the low
position.
Push control E upwards.
Tilt the seat back forwards.
You now have a table with two cup
holders. Removing a seat
Fold the corresponding seat.
Grasp the two bars
G under the seat
and tighten them securely.
The front anchorages unlock.
Lift the seat and carry it using the
carrying handle H.
This turning operation must
be carried out with the en-
gine switched off.
It is prohibited to sit facing
the rear when the vehicle is
being driven.
Never use the adjusting straps to re-
move, reit or transport a seat.
When the vehicle is being driven, it is
prohibited to place a side seat in the
closed position, when a passenger is
sitting in the 3rd row.
Turning a seat round
The rear seats can be placed in the
'rearwards facing' position.
For this, after the seat has been
folded, carry out the removal and
replacing operations for the seat and
turn it round.
Folding the centre seat
Place the seat in the table position.
Lift control F.
Place the seat in the closed position. Reitting a seat
Check that there is no obstacle
obstructing the slides or prevent-
ing correct locking of the seat.
Locate the front anchorages in the
slides (if necessary tighten the two
bars
G securely).
Tilt the folded seat towards the rear.
The rear anchorages lock.
Lift the seat back (for the centre seat,
move control E)

Seats, bench seats84 -
30-08-2004
85Seats, bench seats-
30-08-2004
THE REAR SEAT
Forwards/backwards adjustment
Lift bar A and slide the seat towards
the front or the rear.
Note:
to make it easier to load the
vehicle through the tailgate, you can
pull on strap B and slide the seat
forwards. Rear parcel shelf position
Place the head restraints in the low
position.
Pull the strap
C upwards, from the
tailgate.
Tilt the seat back on the seat cushion. Removing the seat
Fold down the seat.
Grasp the two bars
E underneath
the seat.
The front anchorages unlock.
Note: for removal and reitting, pass
the rear seat, in the "folded" position,
through the sliding side doors.
Never use the adjustment
straps to remove, reit or
transport the seat. Folding the seat
Place the head restraints in the low
position.
Pull the strap
C upwards, from the
tailgate.
Fold the seat back onto the seat
cushion.
Pull the lever D to unlock the rear
anchorages.
Place the seat in the "folded" position.
When driving, attach the retaining
straps to the handles. Reitting the seat
Check that there is nothing block-
ing the runners which could pre-
vent corrrect locking of the seat
anchorages.
Position the front anchorages at the
front stop of the runners.
Tilt the folded seat rearwards.
The rear anchorages then lock.
Unlock the seat back and lift it using
the strap
C.

Seats, bench seats84 -
30-08-2004
85Seats, bench seats-
30-08-2004
REAR HEAD RESTRAINTS
The rear head restraints can be
removed and have two positions;
- high, position for use
- low, storage position
To raise or lower a head restraint,
pull it forwards sliding it at the same
time.
To remove it, place it in the high posi-
tion, push the lug and pull it forwards
and upwards.
To reit it, engage the head restraint
rods in the holes taking care to re-
main in the centreline of the seat
back.Never drive with the head
restraints removed, they
must be in place and cor-
rectly adjusted.