wipers PEUGEOT 807 2009 Owners Manual

Page 5 of 257

Interior
10

5. Control block.

6. Steering wheel audio equipment
controls.

7. Wipers/wash-wipe/trip computer
controls.

8. Gear lever.

9. Ignition.

1. Interior protection alarm
deactivation button.

2. Speed limiter/cruise control
switches.

3. Lights and direction indicators
controls.

4. Driver's air bag.
Horn.
10. Headlamp height adjustment.

11. a - Dynamic stability control button
(ESP/ASR).
b - Parking assistance button.

12. Steering wheel adjustment control.
INSTRUMENTS AND CONTROLS

Page 9 of 257

43
3
3
Interior
14
95
Repositioning
SIT COMFORTABLY
SEE CLEARLY
Adjust the height
and depth of the
steering wheel.
Electric exterior mirrors.
Selection Seat belts
Height adjustment.
Fastening. Lights off
Side lights
Main beam headlamps (blue)
Dipped headlamps (green)
Wipers stalk
2 fast.
1 normal.
I intermittent.
0 off.

 single wipe.
AUTO, press the stalk down. AUTO, automatic switching
on of the lights Adjustment
86 45
48

Page 43 of 257

Steering wheel controls
ERGONOMICS and COMFORT
3
47
Automatic "Follow-Me-Home"
lighting
With the ignition off, when you leave
your vehicle with the automatic
switching on of the lights function
activated , the side lights and dipped
headlamps remain on for the selected
duration.
To deactivate or activate this
function, go to the display
confi guration menu.
The duration of the timed period must
also be set (15, 30, 60 seconds), via
the display confi guration menu.
Carry out these operations when the
vehicle is stationary.
HEADLAMPS BEAM
Depending on the load in your
vehicle, the beam setting must be
adjusted.

0 - 1 or 2 people in the front seats.

1 - 5 people.

2 - 6 to 8 people.

3 - Driver + maximum authorised
loads.

Initial setting is position 0.
In foggy weather or in snow,
the brightness sensor can
detect suffi cient light. As a
consequence, the lights will not come
on automatically.
Automatic switching on of the lights Deactivation
Turn the ring forwards or rearwards.
The deactivation of this function is
accompanied by a message on the
display.
The function is deactivated temporarily
when you use the manual lights stalk.

If the brightness sensor does not
function correctly , the lights come on
accompanied by the service warning
light, an audible signal and a message
on the display.
Contact a PEUGEOT dealer .
Do not cover the brightness
sensor located in the centre of the
fascia. It is used for the automatic
switching on of the lights and for the
automatic wipers.

Activation
Turn the ring to the AUTO position.
The activation of this function is
accompanied by a message on the
display.
AUTOMATIC ADJUSTMENT OF
THE XENON HEADLAMPS
On vehicles which are fi tted with xenon
headlamps, this system automatically
corrects the height of the light beam,
regardless of the load in the vehicle.
The driver is then guaranteed optimum
lighting without dazzling other road
users.
Cancelling:

 "fl ash" the headlamps,

 get out of the vehicle and lock it.
If your vehicle is fi tted
with a brightness
sensor, the side lights
and dipped beam
headlamps switch on
automatically if the
light is poor, or during operation of the
windscreen wipers. They switch off
as soon as the light becomes bright
enough or the windscreen wipers stop.
This function is not compatible with the
daytime lights.

Page 44 of 257

Steering wheel controls
48
WINDSCREEN WIPER STALK
Manual windscreen wipers Special position of
the windscreen wipers
In the minute following switching
off of the ignition, any action on the
stalk positions the wipers against the
windscreen uprights.
This action enables you to position
the wiper blades for winter parking,
cleaning or replacement. Vehicle fitted with the
automatic windscreen
wipers control
Do not cover the rain sensor located in
the centre of the fascia.
On vehicles which are fi tted with
this control, in the AUTO position,
the windscreen wipers operate
automatically and adapt their speed
to the intensity of the rainfall .
When not in AUTO mode, for the
other positions, refer to the manual
windscreen wipers section.

The command must be reactivated
whenever the ignition has been
switched off for more than one
minute:

 move the stalk to any position,

 then move it back to the required
position.

2 Fast wipe
(heavy rain).

1 Normal wipe (moderate rain).

l Intermittent wipe.

0 Off.

 Single wipe
(press downwards). Refer to the "Changing a
windscreen wiper blade" section of
chapter 8.
Wash-wipe and headlamp wash
Pull the stalk towards you, the wash-
wipe is accompanied by a timed sweep
of the wipers.
If your vehicle is fi tted with this
function, the headlamp wash is linked
with the wash-wipe, it is triggered if the
dipped headlamps are on. To park the wipers in their normal
position after this has been done, switch
on the ignition and move the stalk.
To top up the levels, refer to the
"Levels" section of chapter 6.
In the I ntermittent position, the wiping
speed is in proportion to the vehicle
speed.

Page 45 of 257

Steering wheel controls
ERGONOMICS and COMFORT
3
49
Activation
Press the control downwards.
Activation of the function is
accompanied by a message on the
display.

The automatic windscreen wipers
function must be reactivated if the
ignition has been switched off for more
than one minute, by pressing the stalk
downwards.
Rear windscreen wiper
Turn the ring to the fi rst
notch. The wiping speed is
inversely proportional to the
speed of the vehicle.
Rear windscreen wash
Turn the ring past the fi rst
notch: the windscreen wash
then the windscreen wiper
operate for a fi xed time. Good practice
When using an automatic car wash,
switch off the ignition without setting
the alarm.
In winter, it is advisable to wait until the
windscreen is completely clear of ice
before activating the automatic wiping.
In the event of a considerable amount
of snow or ice, switch on the rear
screen demister. Once de-icing is
complete, remove the snow or ice
which has accumulated on the rear
wiper blade. You can now operate the
rear windscreen wiper.
If a tailgate bicycle carrier
is used, deactivate the rear
wiper by going to the display’s
confi guration menu.
Deactivation/Switching off
Place the windscreen wipers stalk in
position
I , 1 or 2 . Deactivation of the
function is accompanied by a message
on the display.

In the event of malfunction of the
automatic windscreen wipers, the
windscreen wipers will operate in
intermittent mode.
Contact a PEUGEOT dealer to have
the system checked.
Switch off the automatic wiping when
using an automatic car wash.
In winter, it is advisable to wait until the
windscreen is completely clear before
activating the automatic wiping. Automatic wiping - reverse gear

- place the front wipers stalk in a
position other than 0 .

- engage reverse gear.

- the rear wiper operates with intermittent wiping.

Page 135 of 257

135
TROUBLESHOOTING
7
Changing a fuse


Rating
(Amps)
Functions

1 20 Engine control unit, Fuel supply and air supply systems, Fan assembly.

2 15 Horn.

3 10 Front and rear wash-wipe pump.

4 20 Headlamp wash pump.

5 15 Fuel supply system.

6 10 Power steering, Secondary brake pedal switch, Automatic gearbox cont rol unit.

7 10 Braking system (ABS/ESP).

8 20 Starter control.

9 10 Engine control unit.

10 30 Fuel supply and air supply systems, Emission control systems.

11 40 Front air conditioning.

12 30 Windscreen wipers.

13 40 Built-in systems interface.

14 30 Not used.

Page 136 of 257

136
Changing a wiper blade
CHANGING A WINDSCREEN
WIPER BLADE
- Reconnect the windscreen-wash pipe and push back the wiper arm.

To return the windscreen wipers
to their normal position, switch on
the ignition and operate the wipers
stalk.
Placing the wiper blades in the
special position
- Less than a minute after switching
off the ignition, operate the wipers
stalk to position the wiper blades
along the windscreen uprights
(special position).
Changing a windscreen wiper blade
- Lift the wiper arm, then disconnect the windscreen-wash pipe.
- Unclip the blade and remove it.
- Fit the new blade. Changing the rear wiper blade
- Lift the wiper arm, then unclip the
blade and remove it.
- Fit the new blade and push back the wiper arm.

Page 215 of 257

09
1
TRIP COMPUTER
VEHICLE DIAGNOSTICS
Press the MAIN button or press the MODE button several times in succession until the trip computer is displayed.
- The "vehicle" tab: The range, the current consumption and the distance remaining. - The "1" (route 1) tab with: The average speed, the average consumption and the distance travelled calculated over route "1". - The "2" (route 2) tab with the same functions for a second route.
Range: displays the distance which can travelled with the remaining displays the distance which can travelled with the remaining fuel detected in the tank, in relation to the average consumption over fuel detected in the tank, in relation to the average consumption over the last few miles (kilometres). This displayed value may vary signifi cantly follow ing a change in the This displayed value may vary signifi cantly following a change in the vehicle speed or the relief of the route. When the range falls below 20 miles (30 km), dashe s are displayed. When the range falls below 20 miles (30 km), dashes are displayed. After fi lling with at least 5 litres of fuel, the range is recalculated and After fi lling with at least 5 litres of fuel, the range is recalculated and is displayed when it exceeds 60 miles (100 km). If, whilst driving, dashes are displayed continuou sly in place of the If, whilst driving, dashes are displayed continuously in place of the digits, contact a PEUGEOT dealer.
Current consumption: only calculated and displayed aayed above 20 mph (30 km/h).
Average consumption: this is the average quantity of fuel this is the average quantity of fuel consumed since the last trip computer zero reset.
Distance travelled: calculated since the last trip compucomputer zero reset.
Distance remaining to the destination: calculated wited with reference to the fi nal destination, entered by the user. If guidance is activated, to the fi nal destination, entered by the user. If guidance is activated, the navigation system calculates it as a current va lue.
Average speed: this is the average speed calculated since the last this is the average speed calculated since the last trip computer zero reset (ignition on).
Each press of the button at the end of the wipers stalk dstalk displays the various trip computer data in succession, according to the display. various trip computer data in succession, according to the display.
A FEW DEFINITIONS