reset Peugeot Boxer Dag 2010 Owner's Manual

Instruments and controls
35
2
READY TO SET OFF
SERVICE INDICATOR
For a few seconds after the ignition is
switched on, the spanner symbolising the
service indicator comes on: the screen
informs you when the next service is due,
in accordance with the manufacturer's
servicing schedule indicated in the servicing
booklet. This information is determined in
relation to the distance travelled since the
previous service.
LIGHTING RHEOSTAT
The rheostat is active when the lighting is on.
After a few seconds, the display returns to
its usual functions.
Use these controls to adjust the
brightness of the instrument panel.
There are 8 levels.
A long press returns you to the main menu.
Refer to "Mode" section of chapter 4.
Deterioration of the engine oil (100 and 120 bhp engines)
The "Oil Life" function determines the
service interval, between 20,000 miles
(30,000 km) and 30,000 miles (45,000 km),
depending on the wear of the engine oil.
The engine control unit tests the degree of
wear of the engine oil. Refer to the list of checks in the
servicing booklet which was given to
you on handover of the vehicle.
Reminder of servicing information
At any time, to access the service indicator,
press briefly on the MODE button.
Use the up/down arrows to see the
scheduling and engine oil wear information.
Pressing the MODE button again allows you
to return to the various display menus.
Menu... Choose...
Allows you
to...

12
Service Service
(Miles/km
before oil
change) Display the
distance
remaining
before the
next oil
change.
Oil Display the
oil level.
Resetting to zero
The stopping of the permanent flashing of
the indicator is carried out by an authorised
repairer with a diagnostic tool.
In this case, your vehicle must be serviced
as soon as possible (within approximately
600 miles/1 000 km).
The function must be reset to zero every
time the engine oil is changed.
You are warned by the flashing of
the engine oil pressure warning
lamp and a message on the
instrument panel every time you
start the engine, if your vehicle is fitted with
this function.

72
Trip computer
The TRIP button, located at the end of the
wiper stalk, provides access to the following
information:
- Ambient
temperature
This indicates the temperature outside the vehicle.
- Range
This indicates the distance that can still be travelled with the fuel remaining in
the tank on the basis of the average
consumption over the last few miles
(kilometres) travelled. -
Average speed A
This is the average speed calculated since the last trip computer zero reset
(with the ignition on).
- Trip duration A
This indicates the total time since the last trip recorder zero reset.
-
Distance A
This indicates the distance travelled since the last trip computer zero reset.
- Average
fuel
consumption A
This is the average quantity of fuel consumed since the last trip computer
zero reset.
- Current
fuel
consumption A
This is the average quantity of fuel consumed during the last few seconds.
TRIP COMPUTER
If TRIP B is activated on the MODE menu:
- Distance B
- Average fuel consumption B
- Average speed B
- Trip duration B

87
4
TECHNOLOGY ON BOARD
Audio equipment

Scroll the
display

Select

Display

Select

Display

Select

Display

Select

Display

Enables you
to…
PRESET USER CLASSIC ROCK JAZZ Select pre-defined equaliser settings.
Select USER to set the equaliser manually then go
to the
EQ SET menu.
Bass and Treble adjustments are always possible.

EQ SET
If USER is
selected in
PRESET,
this menu is
displayed.
Programme the 7 bands of the equaliser manually.
To store the settings, press MENU.

TA OFF TA ON Receive traffic information from the FM radio stat ions.

EXT EXT VOL EXT OFF EXT
23 Adjust or cut off external sound sources.

LIMIT ON NO LIMIT Activate the maximum volume setting when audio
system is on.

Voice commands
98 VOICE COMMANDS
The key words which can be recognised by the system are organised into three levels (levels 1, 2 and 3).
When you say a level 1 command, the system makes t he level 2 commands available; when you say a level 2 command,
the system makes the level 3 commands available.
SETTINGS

Level 1 Level 2 Level 3
Actions
Settings User data Activation of the hands-free system SETTINGS menu.

Activation of the USER DATA menu.
Delete users Deletion of the data recorded for all of the users.
Delete phone book Deletion of the phone book data.
Download phone book Transfer of the phone books from your mobile telep
hone to the hands-free
system (available according to the type of mobile).
Add Contacts Transfer of the names from your mobile telephone t
o the hands-free system
(available according to the type of mobile).
Reset all Deletion of the pairing data and of the phone books/co
ntacts of all of the
telephones paired, with restoring of the default settings of the hands-free system.
Pairing Activation of the pairing procedure for a new mobile telephone.
Update/Updates Activation of the updating of the system.
Pause Update/Pause Updates/Interrupt Updates/
Interrupt Update Temporary suspension of the current update.
Resume Update/Resume Updates Resuming of the previ ously suspended update.