Peugeot Partner VU 2007 Owner's Guide

Instruments, controls and displays24 -
DISPLAY A
This displays the following informa-
tion:
- the time,
- the date,
- the audio system displays,
- a door check (e.g.: "left front door open"),
- warning messages (e.g. "remote control battery flat") or information
messages (e.g. "economy mode
active"), displayed temporarily.
Briefly pressing button
1 alternates
between the total and trip distance
displays.
To reset the trip recorder to zero,
when it is displayed press button 1
until zeros appear.
Total distance recorder
With the lights on, press the button
to vary the intensity of the lighting of
the instruments and controls. When
the lighting reaches the minimum (or
maximum) setting, release the button
then press it again to increase (or re-
duce) the brightness.
As soon as the lighting is of the re-
quired brightness, release the button.
Lighting rheostat
CLOCK
Button 1 : hour adjustment
Button 2 : minute adjustment
Press and hold the button for rapid
advance.

Instruments, controls and displays24 -
DISPLAY A
This displays the following informa-
tion:
- the time,
- the date,
- the audio system displays,
- a door check (e.g.: "left front door open"),
- warning messages (e.g. "remote control battery flat") or information
messages (e.g. "economy mode
active"), displayed temporarily.
Briefly pressing button
1 alternates
between the total and trip distance
displays.
To reset the trip recorder to zero,
when it is displayed press button 1
until zeros appear.
Total distance recorder
With the lights on, press the button
to vary the intensity of the lighting of
the instruments and controls. When
the lighting reaches the minimum (or
maximum) setting, release the button
then press it again to increase (or re-
duce) the brightness.
As soon as the lighting is of the re-
quired brightness, release the button.
Lighting rheostat
CLOCK
Button 1 : hour adjustment
Button 2 : minute adjustment
Press and hold the button for rapid
advance.

25Instruments, controls and displays-
Adjusting the parameters
display A
Press and hold button A for two sec-
onds to access the settings; the data
flashes, indicating it is ready to be
modified.
Then, each press of button A scrolls
through the various data in the fol-
lowing order:
- language of information displayed,
- hours (12 then 24 hour mode),
- minutes,
- year,
- month,
- day.
Pressing button B alters the value of
the parameter selected. Press and
hold for rapid advance (return to start
after the last possible value).
After 7 seconds with no action, the
standard display returns; the modi-
fied data is now recorded.MONOCHROME DISPLAY B
This enables the following informa-
tion to be displayed:
- the time,
- the date,
- the outside temperature (this flash- es accompanied by the message
"Ice alert"),
- the radio displays,
- the status of the doors. The display shows you, by means of a graphic,
whether a door is open,
- the warning messages (e.g. "bat- tery charge fault") or information
messages (e.g. "fuel level low"),
displayed temporarily, can be
cleared by pressing button C or D,
- the trip computer. Setting the parameters screen B
Press button
C for two seconds to
access the settings. The informa-
tion flashes to show it is ready to be
modified.
Then, individual presses on button C
allow you to scroll through the vari-
ous data in the following sequence:
- language in which the information is displayed,
- unit of distance (kms or miles),
- unit of temperature (degrees Cel- sius or Fahrenheit),
- time format (12 then 24 hour mode),
- hour,
- minutes,
- year,
- month,
- day.
Pressing button D allows you to
change the information selected.
Maintain the pressure for rapid scroll-
ing.
After 7 seconds without operation,
the screen returns to the normal
display and the modified data is
recorded.

25Instruments, controls and displays-
Adjusting the parameters
display A
Press and hold button A for two sec-
onds to access the settings; the data
flashes, indicating it is ready to be
modified.
Then, each press of button A scrolls
through the various data in the fol-
lowing order:
- language of information displayed,
- hours (12 then 24 hour mode),
- minutes,
- year,
- month,
- day.
Pressing button B alters the value of
the parameter selected. Press and
hold for rapid advance (return to start
after the last possible value).
After 7 seconds with no action, the
standard display returns; the modi-
fied data is now recorded.MONOCHROME DISPLAY B
This enables the following informa-
tion to be displayed:
- the time,
- the date,
- the outside temperature (this flash- es accompanied by the message
"Ice alert"),
- the radio displays,
- the status of the doors. The display shows you, by means of a graphic,
whether a door is open,
- the warning messages (e.g. "bat- tery charge fault") or information
messages (e.g. "fuel level low"),
displayed temporarily, can be
cleared by pressing button C or D,
- the trip computer. Setting the parameters screen B
Press button
C for two seconds to
access the settings. The informa-
tion flashes to show it is ready to be
modified.
Then, individual presses on button C
allow you to scroll through the vari-
ous data in the following sequence:
- language in which the information is displayed,
- unit of distance (kms or miles),
- unit of temperature (degrees Cel- sius or Fahrenheit),
- time format (12 then 24 hour mode),
- hour,
- minutes,
- year,
- month,
- day.
Pressing button D allows you to
change the information selected.
Maintain the pressure for rapid scroll-
ing.
After 7 seconds without operation,
the screen returns to the normal
display and the modified data is
recorded.

Audio equipment26 -
AUDIO RB3
Stalk movementFunction
1 - Press (behind) Increase volume.
2 - Press (behind) Decrease volume.
1 + 2 - Simultaneous press Sound cut-off (mute); restoring of the sound b y pressing any button.
3 - Press Automatic search of higher frequencies (radio).
4 - Press Automatic search of lower frequencies (radio).
5 - Press the end Change of source (radio/cassette).
6 - Rotation (clockwise) Selection of next station stored in memory (radio).
7 - Rotation (anti-clockwise) Selection of previous station stored in memory (radio).

27Audio equipment-
ButtonFunction
A Radio on/off.
B - Decrease volume.
C + Increase volume.
D RDS RDS function on/off.
Press for more than 2 seconds: regional following mode on/off.
E TA Traffic information priority on/off.
F Press fully: cassette rewind.
G Press fully: fast forward.
F + G   Press half way: reversal of direction of play of the cassette.
Press fully: Ejection of the cassette.
H Selection of bass, treble, loudness, sound distribution and a
utomatic volume correction.
I Increase the setting of the functions associated with button
H .
J Decrease the setting of the functions associated with button
H .
K SRC Selection of source: radio or cassette.
L Manual and automatic search of higher frequency.
M MAN Manual/automatic operation of buttons L and N in radio mode.
N Manual and automatic search of lower frequency.
O BND
AST Selection of FM1, FM2, FMast and AM wavebands.
Press for more than 2 seconds: automatic storing of stations in memory
(autostore).
1 to 6 1 2 3 4 5 6 Selection of station stored in memory.
Press for more than 2 seconds: storing of a station in memory.

Audio equipment30 -
GENERAL FUNCTIONSAUDIO SETTINGS
Adjusting the loudness
This function automatically empha-
sises bass and treble tones.
Press button I or J to switch the func-
tion on or off.
On/off
With the ignition key
in the accessories or
ignition position, press
button
A to switch the
set on or off.
The set can operate for 30 minutes
without the vehicle ignition being
switched on.
Anti-theft system
The audio system is coded in such a
way that it can operate only on your
vehicle. It would not function if fitted
to another vehicle.
The anti-theft system is automatic
and requires no action on your
part.ADJUSTING THE VOLUME
Adjusting the bass
Adjusting the treble
When "TREB" is displayed, press
button I or J to vary the setting.
- "TREB -9" for a minimum treble
setting,
- "TREB 0" for a normal setting,
- "TREB +9" for a maximum treble
setting.
Press button
H sev-
eral times in succes-
sion to access the
bass ( BASS), treble
(TREB), loudness
(LOUD), fader (FAD) ,
balance ( BAL) and
automatic volume
correction.
Exit from audio mode is automatic
after a few seconds without pressing
any button, or by pressing button H
after configuration of the automatic
volume correction.
Note: bass and treble settings are
specific to each source. It is possi-
ble to set them differently for radio,
cassette (RB3), CD (RD3) and CD
changer. When
"BASS" is dis-
played, press button
I or J to vary the set-
ting.
- "BASS -9" for a
minimum bass set-
ting,
- "BASS 0" for a normal setting,
- "BASS +9" for a maximum bass
setting.
Press button C to in-
crease the volume, or
button B to decrease
it.
Continuous pressure
on buttons C and B al-
lows a gradual adjust-
ment of the volume.

31Audio equipment-
RADIO
Notes on radio reception
Your car radio is subject to phenome-
na which do not affect domestic radio
sets. Both AM (MW/LW) and FM re-
ception are subject to various forms
of interference. This is no reflection
on the quality of the equipment, but
is due to the nature of the signals and
the way in which they are transmit-
ted.
On MW/LW, interference may be no-
ticed when passing under high voltage
power lines or bridges, or in tunnels.
On FM, interference may be the re-
sult of increasing distance from the
transmitter, deflection of the signals
by obstacles (mountains, hills, build-
ings, etc.), or of being in an area
which is not covered by a transmit-
ter.Selecting a waveband
Adjusting the front/rear sound
distribution (Fader)
When
"FAD" is displayed, press but-
ton I or J.
Button I increases the volume in the
front.
Button J increases the volume in the
rear.
Adjusting the right/left sound
distribution (Balance)
When "BAL" is displayed, press but-
ton I or J.
Button I increases the volume on the
right-hand side.
Button J increases the volume on the
left-hand side.
Automatic volume correction
This function enables the volume to
be automatically adjusted depending
on the level of noise produced by the
speed of the vehicle.
Press buttons I or J to switch the
function on or off. Audio RB3:
press the
"SRC" button several
times in succession.
Selecting radio mode
Audio RD3:
press button R.
Audio RB3: briefly
press the "BND/AST"
button to select the
FM1, FM2, FMast and
AM wavebands.
Audio RD3: briefly
press button R to select
the FM1, FM2, FMast
and AM wavebands.

31Audio equipment-
RADIO
Notes on radio reception
Your car radio is subject to phenome-
na which do not affect domestic radio
sets. Both AM (MW/LW) and FM re-
ception are subject to various forms
of interference. This is no reflection
on the quality of the equipment, but
is due to the nature of the signals and
the way in which they are transmit-
ted.
On MW/LW, interference may be no-
ticed when passing under high voltage
power lines or bridges, or in tunnels.
On FM, interference may be the re-
sult of increasing distance from the
transmitter, deflection of the signals
by obstacles (mountains, hills, build-
ings, etc.), or of being in an area
which is not covered by a transmit-
ter.Selecting a waveband
Adjusting the front/rear sound
distribution (Fader)
When
"FAD" is displayed, press but-
ton I or J.
Button I increases the volume in the
front.
Button J increases the volume in the
rear.
Adjusting the right/left sound
distribution (Balance)
When "BAL" is displayed, press but-
ton I or J.
Button I increases the volume on the
right-hand side.
Button J increases the volume on the
left-hand side.
Automatic volume correction
This function enables the volume to
be automatically adjusted depending
on the level of noise produced by the
speed of the vehicle.
Press buttons I or J to switch the
function on or off. Audio RB3:
press the
"SRC" button several
times in succession.
Selecting radio mode
Audio RD3:
press button R.
Audio RB3: briefly
press the "BND/AST"
button to select the
FM1, FM2, FMast and
AM wavebands.
Audio RD3: briefly
press button R to select
the FM1, FM2, FMast
and AM wavebands.

Audio equipment32 -
Briefly press buttonL or N to search
for the station immediately above or
below. By continuing to press the
button in the direction selected, you
will obtain continuous scrolling of the
frequency.
The scrolling stops at the first sta-
tion found as soon as the button is
released.
If the TA traffic information pro-
gramme is selected, only stations
broadcasting this type of programme
are selected.
Searching for a station occurs first in
"LO" sensitivity (selection of the most
powerful transmitters) during scan-
ning of the waveband, then in "DX"
sensitivity (selection of the weakest
and most distant transmitters).
To make a direct search in "DX" sen-
sitivity, press button L or N twice. Manual station search
Press the
"MAN" button.
Briefly press button L or N to in-
crease or decrease the frequency
displayed.
By continuing to press the button in
the direction selected, you will obtain
continuous scrolling of the frequen-
cy.
The scrolling stops at the first sta-
tion found as soon as the button is
released.
Pressing the "MAN" button again
returns you to automatic station
search.
Manual storing of stations in the
memory
Select the station required.
Press one of the buttons "1" to "6"
for more than two seconds.
The sound stops then becomes audi-
ble again, confirming that the station
has been stored in the memory.
Automatic station search
Automatic storing of FM stations
in the memory (autostore)
Audio RB3: press and
hold the "BND/AST"
button for more than
two seconds.
Audio RD3: press and
hold button R for more
than two seconds.
Your radio automatically stores the
6 stations with the strongest signal in
FM . These stations are stored in the
FMast waveband.
If it is not possible to find 6 stations,
the remaining memories are empty.
Recalling stations stored in the
memory
For each waveband, briefly press
buttons "1" to "6" to recall the cor-
responding station.