dip stick PONTIAC G6 2007 Owners Manual

ICE POSSIBLE:This message displays when the
outside air temperature is cold enough to create
icy road conditions. Adjust your driving accordingly.
KEY FOB BATT (Battery) LOW:This message
displays if the Remote Keyless Entry (RKE)
transmitter battery is low. Replace the battery in
the transmitter. See “Battery Replacement”
underRemote Keyless Entry System Operation on
page 101.
LOW FUEL:This message displays along with a
low fuel warning light on the instrument panel
cluster when your vehicle is low on fuel. Rell the
fuel tank as soon as possible. SeeLow Fuel
Warning Light on page 208,Fuel on page 310,
andFilling the Tank on page 313.
LOW OIL LEVEL:This message may display on
some vehicles. For correct operation of the low oil
sensing system, your vehicle should be on a level
surface. A false LOW OIL LEVEL message may
appear if the vehicle is parked on a grade. The oil
level sensing system does not check for actual oil
level if the engine has been off for a short period of
time. The oil level is never checked while the
engine is running. If the LOW OIL LEVEL message
appears, and your vehicle has been parked on levelground with the engine off for at least 30 minutes,
the oil level should be checked by looking at the oil
dipstick. Prior to checking the oil level, be sure the
engine has been off for a few minutes and your
vehicle is on a level surface. Then check the
dipstick and add oil if necessary. SeeEngine Oil on
page 325.
LOW WASHER FLUID:This message displays
when your vehicle is low on windshield washer
uid. Rell the windshield washer uid reservoir as
soon as possible. See “Adding Washer Fluid”
underWindshield Washer Fluid on page 350.
PARKING BRAKE:This message displays if the
parking brake is left engaged and you try to
drive away. SeeParking Brake on page 135for
more information.
POWER STEERING:This message displays if a
problem has been detected with the electric
power steering, if your vehicle has this feature.
Have your vehicle serviced immediately by
your dealer.
SERVICE AIR BAG:This message displays if
there is a problem with the airbag system.
Have your vehicle serviced immediately by your
dealer.
214

A. Engine Air Cleaner/Filter. SeeEngine Air
Cleaner/Filter on page 330.
B. Engine Oil Fill Cap. See “When to Add Engine
Oil” underEngine Oil on page 325.
C. Engine Oil Dipstick. See “Checking Engine Oil”
underEngine Oil on page 325.
D. Engine Coolant Surge Tank. SeeEngine
Coolant on page 339.
E. Pressure Cap. SeePressure Cap on page 342.F. Brake Master Cylinder Reservoir. See “Brake
Fluid” underBrakes on page 352.
G. Battery. SeeBattery on page 355.
H. Windshield Washer Fluid Reservoir. See
“Adding Washer Fluid” underWindshield
Washer Fluid on page 350.
I. Engine Compartment Fuse Block. SeeEngine
Compartment Fuse Block on page 418.
319

A. Engine Air Cleaner/Filter. SeeEngine Air
Cleaner/Filter on page 330.
B. Power Steering Fluid Reservoir. SeePower
Steering Fluid on page 349.
C. Engine Oil Fill Cap. See “When to Add Engine
Oil” underEngine Oil on page 325.
D. Engine Oil Dipstick. See “Checking Engine Oil”
underEngine Oil on page 325.
E. Engine Coolant Surge Tank. SeeEngine
Coolant on page 339.F. Pressure Cap. SeePressure Cap on page 342.
G. Brake Master Cylinder Reservoir. See “Brake
Fluid” underBrakes on page 352.
H. Battery. SeeBattery on page 355.
I. Engine Compartment Fuse Block. SeeEngine
Compartment Fuse Block on page 418.
J. Windshield Washer Fluid Reservoir. See
“Adding Washer Fluid” underWindshield
Washer Fluid on page 350.
321

A. Engine Air Cleaner/Filter. SeeEngine Air
Cleaner/Filter on page 330.
B. Power Steering Fluid Reservoir. SeePower
Steering Fluid on page 349.
C. Engine Oil Fill Cap. See “When to Add Engine
Oil” underEngine Oil on page 325.
D. Engine Oil Dipstick. See “Checking Engine Oil”
underEngine Oil on page 325.
E. Electric Engine Cooling Fans. SeeCooling
System on page 345.
F. Engine Coolant Surge Tank. SeeEngine
Coolant on page 339.
G. Pressure Cap. SeePressure Cap on page 342.H. Brake Master Cylinder Reservoir. See “Brake
Fluid” underBrakes on page 352.
I. Automatic Transaxle Fluid Dipstick (Out of
View). See “Checking the Fluid Level” under
Automatic Transaxle Fluid (2.4L L4 and 3.5L V6
Engines) on page 332orAutomatic Transaxle
Fluid (3.6L Engine) on page 332orAutomatic
Transaxle Fluid (3.9L V6 Engine) on page 335.
J. Battery. SeeBattery on page 355.
K. Underhood Fuse Block. SeeEngine
Compartment Fuse Block on page 418.
L. Windshield Washer Fluid Reservoir. See
“Adding Washer Fluid” underWindshield
Washer Fluid on page 350.
323

A. Engine Air Cleaner/Filter. SeeEngine Air
Cleaner/Filter on page 330.
B. Engine Coolant Bleed Valve.
C. Power Steering Fluid. SeePower Steering
Fluid on page 349.
D. Automatic Transaxle Fluid Dipstick (Out of
View). See “Checking the Fluid Level” under
Automatic Transaxle Fluid (2.4L L4 and 3.5L V6
Engines) on page 332orAutomatic Transaxle
Fluid (3.6L Engine) on page 332orAutomatic
Transaxle Fluid (3.9L V6 Engine) on page 335.
E. Engine Oil Fill Cap. See “When to Add
Engine Oil” underEngine Oil on page 325.
F. Engine Oil Dipstick. See “Checking Engine Oil”
underEngine Oil on page 325.
G. Engine Coolant Surge Tank. SeeEngine
Coolant on page 339.
H. Pressure Cap. SeePressure Cap on page 342.
I. Brake Master Cylinder Reservoir. See “Brake
Fluid” underBrakes on page 352.
J. Battery. SeeBattery on page 355.K. Windshield Washer Fluid Reservoir. See
“Adding Washer Fluid” underWindshield
Washer Fluid on page 350.
L. Engine Compartment Fuse Block. SeeEngine
Compartment Fuse Block on page 418.
Engine Oil
Checking Engine Oil
It is a good idea to check the engine oil every time
you get fuel. In order to get an accurate reading,
the oil must be warm and the vehicle must be
on level ground.
The engine oil dipstick handle is a yellow loop.
SeeEngine Compartment Overview on page 318
for the location of the engine oil dipstick.
1. Turn off the engine and give the oil several
minutes to drain back into the oil pan. If you
do not do this, the oil dipstick might not
show the actual level.
2. Pull out the dipstick and clean it with a paper
towel or cloth, then push it back in all the
way. Remove it again, keeping the tip down,
and check the level.
325

When to Add Engine Oil
If the oil is below the cross-hatched area at the
tip of the dipstick, you will need to add at least
one quart/liter of oil. But you must use the right kind.This section explains what kind of oil to use. For
engine oil crankcase capacity, seeCapacities and
Specications on page 424.
Notice:Do not add too much oil. If the engine
has so much oil that the oil level gets above the
upper mark that shows the proper operating
range, the engine could be damaged.
SeeEngine
Compartment Overview
on page 318for the
location of the engine
oil ll cap.
Be sure to add enough oil to put the level
somewhere in the proper operating range. Push
the dipstick all the way back in when you are
through.
L4 Engine
V6 Engine
326

Automatic Transaxle Fluid
(2.4L L4 and 3.5L V6 Engines)
It is not necessary to check the transaxle uid
level. A transaxle uid leak is the only reason for
uid loss. If a leak occurs, take your vehicle to
the dealership service department and have
it repaired as soon as possible.
Change the uid and lter at the intervals listed in
Additional Required Services on page 434, and be
sure to use the transaxle uid listed in
Recommended Fluids and Lubricants on page 442.
Notice:Use of the incorrect automatic
transaxle uid may damage your vehicle, and
the damages may not be covered by your
warranty. Always use the automatic transaxle
uid listed inRecommended Fluids and
Lubricants on page 442.
Automatic Transaxle Fluid
(3.6L Engine)
When to Check and Change Automatic
Transaxle Fluid
A good time to check the automatic transaxle uid
level is when the engine oil is changed.
Change the uid at the intervals listed inAdditional
Required Services on page 434, and be sure to
use the transaxle uid listed inRecommended
Fluids and Lubricants on page 442.
How to Check Automatic Transaxle
Fluid
Because this operation can be a little difficult, you
may choose to have this done at the dealership
service department.
If you do it yourself, be sure to follow all the
instructions here, or you could get a false reading
on the dipstick.
332

Notice:Too much or too little uid can damage
the transaxle. Too much can mean that some of
the uid could come out and fall on hot engine
or exhaust system parts, starting a re. Too
little uid could cause the transaxle to overheat.
Be sure to get an accurate reading if you check
the transaxle uid.
Wait at least 30 minutes before checking the
transaxle uid level if you have been driving:
When outside temperatures are above
90°F (32°C).
At high speed for quite a while.
In heavy traffic — especially in hot weather.
While pulling a trailer.
To get the right reading, the uid should be at
normal operating temperature, which is 180°F to
200°F (82°C to 93°C).
Get the vehicle warmed up by driving about
15 miles (24 km) when outside temperatures are
above 50°F (10°C). If it is colder than 50°F (10°C),
you may have to drive longer.
Checking the Fluid Level
Prepare the vehicle as follows:
1. Park the vehicle on a level place. Keep the
engine running.
2. With the parking brake applied, place the shift
lever in PARK (P).
3. With your foot on the brake pedal, move the
shift lever through each gear, pausing for
about three seconds in each one. Then,
position the shift lever in PARK (P).
4. Let the engine run at idle for three to
ve minutes.
Then, without shutting off the engine, follow
these steps:
The transaxle uid
dipstick handle has this
symbol on it, and is
located near the front of
the engine compartment.
333

SeeEngine Compartment Overview on page 318
for more information on location.
1. Remove the dipstick and wipe it with a clean
rag or paper towel.
2. Reinstall it back in all the way, wait three
seconds and then pull it back out again.
3. Check both sides of the dipstick, and read the
lower level. The uid level must be within the
crosshatched area.
4. If the uid level is in the acceptable range,
reinstall the dipstick back in all the way.How to Add Automatic Transaxle Fluid
Refer to the Maintenance Schedule to
determine what kind of transaxle uid to use. See
Recommended Fluids and Lubricants on page 442.
If the uid level is low, add only enough of the
proper uid to bring the level into the crosshatched
area on the dipstick.
1. Remove the dipstick.
2. Using a long-neck funnel, add enough uid at
the dipstick hole to bring it to the proper level.
It does not take much uid, generally less
than a half pint (0.24 L). Do not overll.
Notice:Use of the incorrect automatic
transaxle uid may damage your vehicle, and
the damages may not be covered by your
warranty. Always use the automatic transaxle
uid listed inRecommended Fluids and
Lubricants on page 442.
3. After adding uid, recheck the uid level as
described under “How to Check Automatic
Transaxle Fluid,” earlier in this section.
4. When the correct uid level is obtained,
reinstall the dipstick back in all the way.
334

Automatic Transaxle Fluid
(3.9L V6 Engine)
When to Check and Change Automatic
Transaxle Fluid
A good time to check the automatic transaxle uid
level is when the engine oil is changed.
Change the uid and lter at the intervals listed
inAdditional Required Services on page 434,
and be sure to use the transaxle uid listed in
Recommended Fluids and Lubricants on page 442.
How to Check Automatic Transaxle
Fluid
Because this operation can be a little difficult, you
may choose to have this done at the dealership
service department.
If you do it yourself, be sure to follow all the
instructions here, or you could get a false
reading on the dipstick.Notice:Too much or too little uid can damage
the transaxle. Too much can mean that some of
the uid could come out and fall on hot engine
or exhaust system parts, starting a re. Too
little uid could cause the transaxle to overheat.
Be sure to get an accurate reading if you check
the transaxle uid.
Wait at least 30 minutes before checking the
transaxle uid level if you have been driving:
When outside temperatures are above
90°F (32°C).
At high speed for quite a while.
In heavy traffic — especially in hot weather.
While pulling a trailer.
To get the right reading, the uid should be at
normal operating temperature, which is 180°F to
200°F (82°C to 93°C).
Get the vehicle warmed up by driving about
15 miles (24 km) when outside temperatures are
above 50°F (10°C). If it is colder than 50°F (10°C),
you may have to drive longer.
335