display PONTIAC G6 2009 Owner's Guide

Radio(s)
The vehicle has one of these radios as its audio
system.
If the vehicle has the Monsoon audio system, it has
eight speakers and an eight channel amplier. The radio
displays MONSOON when the radio or the ignition is
turned on. See your dealer/retailer for details. Radio with a Single CD Player
Radio with a Six-Disc CD Player
3-54

Radio Data System (RDS)
The audio system has a Radio Data System (RDS).
RDS features are available for use only on FM stations
that broadcast RDS information.
With RDS, the radio can do the following:
Seek to stations broadcasting the selected type of
programming
Receive announcements concerning local and
national emergencies
Display messages from radio stations
Seek to stations with traffic announcements
This system relies upon receiving specic information
from these stations and only works when the information
is available. In rare cases, a radio station can broadcast
incorrect information that causes the radio features to
work improperly. If this happens, contact the radio station.
While the radio is tuned to an RDS station, the station
name or call letters appear on the display instead of the
frequency. RDS stations can also provide the time of
day, a program type (PTY) for current programming, and
the name of the program being broadcast.
Playing the Radio
O
(Power):Press to turn the system on and off.
u(Volume):Turn to increase or to decrease the
volume.
DISP (Display):Press to switch the display between
the time and the temperature or the radio station
frequency and the temperature. While the ignition is off,
press to display the time.
For RDS, press to change what appears on the display
while using RDS. The display options are station
name, RDS station frequency, PTY, and the name of
the program (if available).
For XM™ (if equipped), press while in XM mode to
retrieve four different categories of information related
to the current song or channel: Artist, Song Title,
Category or PTY, Channel Number/Channel Name.
To change the default on the display, press the DISP
knob until you see the desired display, then hold
the knob for two seconds. The radio produces a beep
and the selected display is now the default.
3-55

AUTOu(Automatic Volume):With automatic
volume, the audio system adjusts automatically to make
up for road and wind noise as you drive.
Set the volume at the desired level. Press this button to
select LOW, MEDIUM, or HIGH. AUTO VOL LOW,
AUTO VOL MEDIUM, or AUTO VOL HIGH displays.
Each higher setting allows for more volume
compensation at faster vehicle speeds. While driving,
automatic volume increases the volume as necessary,
to overcome noise at any speed. The volume level
should always sound the same while driving. AUTO VOL
NONE displays if the radio cannot determine the
vehicle speed or if the engine is not running. To turn
automatic volume off, press this button until AUTO VOL
OFF displays.
Finding a Station
BAND:Press to switch between FM1, FM2, AM, or
XM1 or XM2. The display shows the selection.
ADJ (Adjust):Turn to select radio stations.
xSEEKw:Press to go to the next or to the previous
station and stay there.
To scan stations, press and hold either arrow for
two seconds until a beep sounds. The radio goes to a
station, plays for a few seconds, then goes to the
next station. Press either arrow again to stop scanning.To scan preset stations, press and hold either arrow
for more than four seconds until two beeps sound.
The radio goes to the rst preset station stored on the
pushbuttons, plays for a few seconds, then goes to
the next preset station. Press either arrow again to stop
scanning presets.
The radio only seeks and scans stations with a strong
signal that are in the selected band.
Setting Preset Stations
Up to 30 stations (six FM1, six FM2, and six AM, six XM1
and six XM2), can be programmed on the six numbered
pushbuttons. To program presets:
1. Turn the radio on.
2. Press BAND to select FM1, FM2, AM,
or XM1 or XM2.
3. Tune in the desired station.
4. Press AUTO TONE to select the equalization.
5. Press and hold one of the six numbered
pushbuttons until a beep sounds. When that
numbered pushbutton is pressed, the station that
was set, returns and the equalization that was
selected is stored for that pushbutton.
6. Repeat the steps for each pushbutton.
3-56

Setting the Tone
(Bass/Midrange/Treble)
TONE (Bass/Midrange/Treble):Press and release the
tone until BASS, MID (midrange), or TREB (treble)
displays. Turn the ADJ (adjust) knob to increase or to
decrease the tone. The display shows the bass,
midrange, or treble level. If a station is weak or has
static, decrease the treble.
To adjust bass, midrange, or treble to the middle
position, select BASS, MID, or TREB. Then press and
hold the tone button for more than two seconds.
One beep sounds and the tone control adjusts to the
middle position.
To adjust all tone controls to the middle position, press
and hold the tone button while no tone control is
displayed. ALL CENTERED displays and a beep
sounds. The bass, midrange, and treble adjusts to the
middle position.
AUTO TONE (Automatic Equalization):Press to
select customized equalization settings designed
for country, jazz, talk, pop, rock, and classical.
The equalization setting last chosen appears on the
display when you rst press this button. Each time you
press this button, another equalization setting displays
and automatic tone or automatic equalization switches to
that preset equalization setting.To return to the manual mode, press the AUTO TONE
button until CUSTOM displays. The bass, midrange, and
treble can manually be adjusted using the tone button.Adjusting the Speakers (Balance/Fade)
BAL/FADE (Balance/Fade):To adjust the balance
between the right and the left speakers:
1. Push and release the balance and fade button until
BAL displays.
2. Turn the ADJ knob to move the sound toward the
right or the left speakers.
To adjust the fade between the front and the rear
speakers:
1. Push and release the balance and fade button until
FADE displays.
2. Turn the ADJ knob to move the sound toward the
front or the rear speakers.
To adjust balance or fade to the middle position, select
BAL or FADE. Then press and hold the balance and fade
button for more than two seconds. One beep sounds and
the speaker control adjusts to the middle position.
To adjust both speaker controls to the middle position,
push and hold the balance and fade button while no
speaker control is displayed. ALL CENTERED displays
and One beep sounds.
3-57

Finding a Program Type (PTY) Station
(RDS and XM™)
To select and nd a desired PTY perform the following:
1. Press the P-TYPE button to activate program
type select mode. PTY for FM or PTYPE for XM and
a program type displays.
2. Turn the ADJ knob to select a PTY.
3. Once the desired PTY is displayed, press the up
SEEK arrow to select the PTY and to take you to
the PTY’s rst station.
4. To go to another station within that PTY press the
up SEEK arrow again. If the radio cannot nd the
desired PTY, NONE FOUND displays and the radio
returns to the last station you were listening to.
After 15 seconds of inactivity or if the P-TYPE
button is pressed again, the radio exits program
type select mode.
BAND (AF – Alternate Frequency):Alternate
frequency lets the radio switch to a stronger station with
the same program type. To turn alternate frequency
on, press and hold BAND for two seconds. FM ALT
FREQ ON and AF displays. The radio can switch
to stations with a stronger frequency.To turn alternate frequency off, press and hold BAND
again for two seconds. FM ALT FREQ OFF displays and
AF disappears from the display. The radio does not
switch to other stations.
This function does not apply for XM Satellite Radio
Service.
RDS Messages
ALERT!:Alert warns of local or national emergencies.
When an alert announcement comes on the current
radio station, ALERT! displays. The announcement is
heard even if the volume is low or a CD is playing. If a
CD is playing, play stops during the announcement.
Alert announcements cannot be turned off.
ALERT! is not affected by tests of the emergency
broadcast system. This feature is not supported by all
RDS stations.
MSG (Message):If the current station has a message,
MSG displays. Press this button to see the message.
The message can display the artist, song title, call
in phone numbers, etc.
If the entire message is not displayed, parts of the
message appears every three seconds. To scroll
through the message, press and release the MSG
button. A new group of words display after every press
of this button. Once the complete message has
3-58

displayed, MSG disappears from the display until
another new message is received. The last message
can be displayed by pressing the MSG button. The last
message can be viewed until a new message or the
radio is turned to a different station.
When a message is not available from a station, NO
MESSAGE displays.
MSG or TRAF (Traffic):If TRAFFIC displays, the
tuned station broadcasts traffic announcements.
If the current tuned station does not broadcast traffic
announcements, press and hold this button for
two seconds and the radio seeks to a station that does.
When a station that broadcasts traffic announcements
is found, the radio stops seeking and TRAF in brackets
displays. When a traffic announcement broadcasts
on the tuned radio station, you will hear it. If no station
is found that broadcasts traffic announcements, NO
TRAFFIC INFO displays.
If TRAF is on the display, press and hold the MSG or
TRAF button for two seconds to turn off the traffic
announcements.
The radio plays the traffic announcement even if the
volume is low. The radio interrupts the play of a CD if
the last tuned station broadcasts traffic announcements.
This function does not apply to XM Satellite Radio
Service.Radio Messages
CALIBRATE:The audio system has been calibrated for
your vehicle from the factory. If CALIBRATE displays,
it means that the radio has not been congured properly
for the vehicle and it must be returned to your
dealer/retailer for service.
LOCKED:This message displays when the
THEFTLOCK
®system has locked up. Take the vehicle
to your dealer/retailer for service.
If any error occurs repeatedly or if an error cannot be
corrected, contact your dealer/retailer.
XM™ Satellite Radio Service
XM™ is a satellite radio service that is based in the
48 contiguous United States and 10 Canadian
provinces. XM Satellite Radio has a wide variety
of programming and commercial-free music,
coast-to-coast, and in digital-quality sound. During your
trial or when you subscribe, you will get unlimited
access to XM Radio Online for when you are not in the
vehicle. A service fee is required to receive the
XM service. For more information, contact XM at
xmradio.com or call 1-800-929-2100 in the U.S. and
xmradio.ca or call 1-877-438-9677 in Canada.
Radio Messages for XM™ Only
SeeXM Radio Messages on page 3-66later in this
section for further detail.
3-59

Playing a CD
Insert a CD partway into the slot, label side up.
The player pulls it in and the CD should begin playing.
Press the eject button or the DISP knob to insert
a CD while the ignition is off.
If the ignition or radio is turned off while a CD is in the
player, it stays in the player. When the ignition or
radio is turned on, the CD starts playing, where it
stopped, if it was the last selected audio source.
As each new track starts to play, the track number
displays.
The CD player can play the smaller 3 inch (8 cm) single
CDs with an adapter ring. Full-size CDs and the
smaller CDs are loaded in the same manner.
Care of CDs
If playing a CD-R, the sound quality can be reduced
due to CD-R quality, the method of recording, the quality
of the music that has been recorded, and the way the
CD-R has been handled. Handle them carefully.
Store CD-R(s) in their original cases or other protective
cases and away from direct sunlight and dust. The
CD player scans the bottom surface of the disc. If the
surface of a CD is damaged, such as cracked, broken,
or scratched, the CD does not play properly or not
at all. Do not touch the bottom side of a CD whilehandling it; this could damage the surface. Pick up CDs
by grasping the outer edges or the edge of the hole
and the outer edge.
If the surface of a CD is soiled, take a soft, lint free
cloth or dampen a clean, soft cloth in a mild, neutral
detergent solution mixed with water, and clean it.
Make sure the wiping process starts from the center
to the edge.
Care of The CD Player
Do not add any label to a CD, it could get caught in the
CD player. If a CD is recorded on a personal computer
and a description label is needed, try labeling the top of
the recorded CD with a marking pen.
The use of CD lens cleaners for CDs is not advised,
due to the risk of contaminating the lens of the CD optics
with lubricants internal to the CD player mechanism.
Notice:If a label is added to a CD, or more than
one CD is inserted into the slot at a time, or an
attempt is made to play scratched or damaged CDs,
the CD player could be damaged. While using the
CD player, use only CDs in good condition without
any label, load one CD at a time, and keep the
CD player and the loading slot free of foreign
materials, liquids, and debris.
If an error displays, see “CD Messages” later in this
section.
3-60

For vehicles that have a Radio with a Six-Disc CD
player, see the following:
LOAD
^:Press to load CDs into the CD player.
This CD player holds up to six CDs.
To insert one CD:
1. Turn the ignition on.
2. Press and release the LOAD
^button.
3. Wait for INSERT CD to ash on the display.
4. Load a CD. Insert the CD partway into the slot,
label side up. The player pulls the CD in.
To insert multiple CDs:
1. Turn the ignition on.
2. Press and hold the LOAD
^button for two seconds.
A beep sounds and MULTI LOAD CD displays, then
INSERT CD and the number displays.
3. Once INSERT CD and the number displays, load a
CD. Insert the CD partway into the slot, label side
up. The player pulls the CD in.
Once the CD is loaded, INSERT CD and the
number displays again. Once INSERT CD and the
number displays again, another CD can be loaded.
The CD player takes up to six CDs. Do not try
to load more than six.To load more than one CD but less than six, complete
Steps 1 through 3. When nished loading CDs, the
radio begins to play the last CD loaded.
If more than one CD has been loaded, a number for
each CD is displayed and the currently selected
slot number is underlined.
EJECT
Z:Press to eject a single CD. The radio
displays EJECTING CD # and the single CD symbol
ashes until the CD is ready to be removed. When the
CD is ready to be removed it ejects part way from
the radio and the display changes to a ashing
REMOVE CD # with the single CD symbol ashing until
the CD is removed. If the CD is not removed within
25 seconds the radio pulls it back in.
Press and hold until a beep sounds to eject multiple
CDs. EJECTING ALL CDS displays with the single CD
symbol ashing. The CD symbol ashes until a CD
is ready to be removed. When the CD is ready to be
removed it ejects part way from the radio and the display
changes to a ashing REMOVE CD # with the single
CD symbol ashing until the CD is removed. If the CD is
not removed within 25 seconds the radio pulls it back
in. After the CD is removed the radio repeats the
previous actions until all of the CDs have been removed
or a CD is pulled back in.
3-61

Playing a Specic Loaded CD
For every CD loaded, a number appears on the display.
To play a specic CD, press the numbered pushbutton
that corresponds to the CD to be played. A small
bar appears under the CD number that is playing, and
the track number displays.
If an error displays, see “CD Messages” later in this
section.
s(Fast Reverse):Press and hold to reverse quickly
within a track. Sound is heard at a reduced volume.
Release to play the passage. Depending on the radio,
T# (track number), the elapsed time, and REV displays.
\(Fast Forward):Press and hold to advance quickly
within a track. Sound is heard at a reduced volume.
Release to play the passage. Depending on the radio,
T#, the elapsed time, and FWD displays.
RPT (Repeat):With repeat, one track or an entire CD
can be repeated.
To use repeat:
To replay a track, press and release the RPT
button. REPEAT ON and RPT displays. Press again
to turn off repeat play. REPEAT OFF displays
and RPT disappears from the display.
To replay a CD on the Radio with Six-Disc CD,
press and hold the RPT button for more than
two seconds. REPEAT ON and RPT displays.
Press again to turn off repeat play. REPEAT OFF
displays and RPT disappears from the display.
RDM (Random):With the random setting, the tracks
can be listened to in random, rather than sequential,
order, on one CD or on all of the CDs.
To use random:
To play the tracks on the CD in random order,
press the RDM button. Depending on the radio,
RANDOM, T# (tracks), and RDM displays. Press
again to turn off random play. RANDOM OFF
displays and RDM disappears from the display.
To play the tracks on all of the CDs that are loaded
in the Radio with a Six-Disc CD player, in random
order, press and hold the RDM button for more than
two seconds. A beep sounds, RANDOM ALL CDS,
and RDM displays. Press again to turn off
random play. RANDOM OFF displays and RDM
disappears from the display.
3-62

xSEEKw:Press the down arrow to go to the start of
the current track, if more than eight seconds have
played. Press the up arrow to go to the beginning of the
next track. If either arrow is held or pressed more
than once, the player continues moving through the CD.
To scan the current CD, press and hold either arrow
for more than two seconds. The CD goes to the
next track, plays the rst 10 seconds, then goes to the
next track. Press either arrow again to stop scanning.
To scan all of the CDs loaded in the Radio with a
Six-Disc CD player, press and hold either arrow for more
than four seconds. The CD goes to the next CD,
plays the rst 10 seconds of the rst track, then goes to
the next CD. Press either arrow again to stop scanning.
DISP (Display) (Radio with Single CD):Press to
see how long the current track has been playing.
T, the track number, and the elapsed time of the track
displays. To change the default on the display, time
or elapsed time, press until you see the desired display,
then hold the knob for two seconds. The radio produces
one beep and the selected display is now the default.
Pressing this button also displays text on commercially
recorded CDs (if available).DISP (Display) (Radio with Six-Disc CD Player):
Press to switch between time, temperature, and
the elapsed time of the track. To change the default
on the display (CD#/Track#/Time, CD#/Track#/
Temperature, or Track#/Elapsed Time/Temperature),
press until the desired display appears, then hold
the knob for two seconds. The radio produces one beep
and the selected display is now the default.
AUTO TONE (Automatic Equalization):Press to
select the desired equalization setting while playing a
CD. The equalization is automatically recalled when
a CD is played. For more information, see “AUTO
TONE” listed previously in this section.
BAND:Press to listen to the radio while a CD is
playing. The inactive CD(s) remains inside the radio for
future listening.
SRCE (Source):Press to play a CD while listening to
the radio. Press again and the system searches for
an auxiliary input device such as a portable audio player.
3-63