display PONTIAC GRAND PRIX 2005 Owners Manual

"(Unlock):Press the unlock button one time to unlock
the driver’s door. Press the unlock button again within
ve seconds to unlock the other doors. The interior lights
will come on and stay on for 20 seconds or until the
ignition is turned on. If enabled through the DIC,
the parking lamps will ash once to indicate unlocking
has occurred. Pressing the lock button on the remote
keyless entry transmitter will disarm the content-theft
deterrent system. SeeContent Theft-Deterrent on
page 2-17for more details.
V(Trunk Release):Press this button to release the
trunk lid. The transaxle must be in PARK (P) for this
feature to operate.
L(Remote Alarm):Press the remote alarm button to
activate an alarm. The ignition must be in off or
accessory for the remote alarm to work. When the
remote alarm button is pressed the headlamps will ash
and the horn will sound repeatedly for two minutes.
The alarm will turn off when the ignition is moved to run
or the remote alarm button is pressed again.The vehicle may have Remote Lock/Unlock
Conrmation. This feature provides feedback that a
command has been received by the vehicle. The
headlamps will ash and the horn may sound briey.
See “Remote Lock Feedback” underDIC Controls and
Displays (Base Level DIC) on page 3-49orDIC
Controls and Displays (Uplevel DIC with Trip Computer)
on page 3-57for programming information.
Matching Transmitter(s) to Your
Vehicle
Each remote keyless entry transmitter is uniquely coded
to prevent another transmitter from unlocking the
vehicle. If a transmitter is lost or stolen, a replacement
can be purchased through your dealer. Remember
to bring any additional transmitters so they can also be
re-coded to match the new transmitter. Once your
dealer has coded the new transmitter, the lost
transmitter cannot unlock the vehicle. The vehicle can
have a maximum of four transmitters coded to it.
2-6

Remote Vehicle Start
Your vehicle may have a remote starting feature. This
feature allows you to start the engine from outside of the
vehicle. It also starts up the vehicle’s heating or air
conditioning systems and rear window defogger. When
the remote start system is active and the vehicle
has an automatic climate control system, it will
automatically regulate the inside temperature. Normal
operation of the system will return after the key is turned
to the on position.
Laws in some communities may restrict the use of
remote starters, for example, requiring a person using
remote start to have the vehicle in view when doing so.
Check local regulations for any requirements on
remote starting of vehicles.
Do not use the remote start feature if your vehicle is
low on fuel. Your vehicle may run out of fuel.
/(Remote Start):Press the lock button and then
press this button to use the remote start feature.
To start the vehicle using the remote start feature,
do the following:
1. Aim the transmitter at the vehicle.
2. Press the transmitter’s lock button, release it and
then immediately press and hold the transmitter’s
remote start button until the vehicle’s turn signal
lights ash or for at least four seconds. The
vehicle’s doors will be locked.
3. When the vehicle starts, the parking lamps will turn
on and remain on while the vehicle is running, and
the DIC will display REMOTE START ACTIVE
PRESS HAZARD SWITCH TO CANCEL when the
vehicle starts.
4. If it is your rst remote start since last driving,
repeat these steps while the engine is still
running for a 10 minute time extension.
When you enter the vehicle during a remote start, and
the engine is still running, turn the key to the RUN
position to drive the vehicle.
2-8

If the vehicle is left running it will automatically shut off
after 10 minutes unless a time extension has been
done. To manually shut off a remote start, do any of
the following:
Aim the remote keyless entry transmitter at the
vehicle and press the remote start button until
the parking lamps turn off.
Turn on the hazards warning ashers.
Turn the ignition switch on and then off.
The remote start feature provides two separate starts,
each with 10 minutes of engine running, or it provides
one start with 10 minutes of engine running which may
be extended by 10 more minutes. If you press and
release the transmitter lock button and then press and
hold the remote start button, on the keyless entry
transmitter, again before the rst 10 minutes of the
engine running time has expired, 10 minutes are added
to the remaining minutes. For example, if the lock
and then the remote start buttons are pressed again
after ve minutes of the engine run time, 10 minutes
are added and you now have 15 minutes of the
engine running. The added 10 minutes is considered
a second start. Once two remote starts or a single start
with a time extension have been provided, the vehicle
must be started normally with the ignition key to
get more remote starts.The remote start feature will not operate if the key is in
the ignition, a door is open or the hood is not closed.
The remote start feature will not operate if there is
an emission control system malfunction. Also, the engine
will turn off during a remote vehicle start if the coolant
temperature gets too high or the oil pressure gets low.
If a remote start is attempted and unsuccessful, the
Driver Information Center (DIC) will display REMOTE
START DISABLED.
2-9

Power Door Locks
To lock or unlock all doors
from inside the vehicle,
use the power door
lock switch located on
either front door.
Move the switch on the driver’s door to the right to lock
or to the left to unlock the doors. Move the switch on
the passenger’s door to the left to lock or to the right to
unlock the doors.
If the vehicle has the content theft-deterrent system, the
vehicle may be programmed to arm the system with
the power door lock switch. See “Lock Switch Arm”
underDIC Controls and Displays (Base Level DIC) on
page 3-49orDIC Controls and Displays (Uplevel
DIC with Trip Computer) on page 3-57for more
information on programming the system.
Delayed Locking
This feature delays the locking of the vehicle’s doors for
ve seconds after the last door is closed. Two chimes
will sound when the power door lock switch or the
LOCK button on the remote keyless entry transmitter is
pressed when a door is open. The chimes indicate
that the delayed locking feature is on.
The doors can be locked immediately by pressing the
power door lock switch or the LOCK button on the
transmitter a second time.
The delayed locking feature will not activate when the
ignition is in RUN or ACC.
You can program this feature on or off through the
Driver Information Center (DIC), if equipped. See
“Personal Programming Mode Screens” underDIC
Controls and Displays (Base Level DIC) on page 3-49
orDIC Controls and Displays (Uplevel DIC with Trip
Computer) on page 3-57. Driver’s Side
2-11

Programmable Automatic
Door Locks
The vehicle’s doors are programmed from the factory to
lock when the shift lever is moved out of PARK (P),
except in REVERSE (R), and to unlock while the shift
lever is moved into PARK (P).
If someone needs to get in or out of the vehicle after
the doors have been locked, place the shift lever
into PARK (P). You may also unlock all doors using the
power door lock switch or unlock one door using the
inside manual door lock.
To program other door locking/unlocking combinations,
see “Personal Programming Mode Screens” under
DIC Controls and Displays (Base Level DIC) on
page 3-49orDIC Controls and Displays (Uplevel DIC
with Trip Computer) on page 3-57.
Lockout Protection
The lockout protection feature makes it more difficult
to lock the key in the vehicle. If the driver’s door is
open while the key is in the ignition, the door cannot be
locked with the power door lock switch.
This feature cannot guarantee that you will never be
locked out of the vehicle. If the key is not left in
the ignition, or, if the manual door lock pin is used, the
key could still be locked inside the vehicle. Always
remember to take the key with you.
To turn this feature on or off see “Personal Programming
Mode Screens” underDIC Controls and Displays
(Base Level DIC) on page 3-49orDIC Controls and
Displays (Uplevel DIC with Trip Computer) on
page 3-57.
2-12

Visor Vanity Mirror
Raise the cover on the top of the sun visor to expose
the vanity mirror. If the vehicle has lighted vanity mirrors,
the lamps come on when the cover is opened.
Theft-Deterrent Systems
Vehicle theft is big business, especially in some cities.
Although the vehicle has a number of theft-deterrent
features, nothing that is put on the vehicle can make it
impossible to steal.
Content Theft-Deterrent
The vehicle has a content theft-deterrent alarm system.
A red light located on top
of the instrument panel,
toward the center of
the vehicle and near the
windshield, will ash slowly
when the system is
armed.The theft-deterrent alarm system needs to be activated
through the Driver’s Information Center (DIC). See
“Theft Deterrent” under the Personal Programming Mode
Screens inDIC Controls and Displays (Base Level
DIC) on page 3-49orDIC Controls and Displays
(Uplevel DIC with Trip Computer) on page 3-57. While
armed, the doors will not unlock with the power door lock
switch. The remote alarm will sound if someone
tampers with the trunk, enters the vehicle without using
the remote keyless entry transmitter or key to unlock
the doors, or turns the ignition on without the proper key.
The horn will sound and the headlamps will ash for
up to two minutes. The system will also cut off the fuel
supply, preventing the vehicle from being driven.Arming with the Power Lock Switch
The vehicle’s content theft-deterrent alarm system can be
activated when the key is removed from the ignition and
the power door lock switch of either the driver’s or front
passenger’s door is used to lock the vehicle. The door
needs to be in the open position when pressing the power
door lock switch. The alarm system will not activate if the
door is closed and the power door lock switch is pressed.
This system can be activated through the Driver’s
Information Center (DIC). See “Lock Switch Arm” under
the Personal Programming Mode Screens inDIC
Controls and Displays (Base Level DIC) on page 3-49
orDIC Controls and Displays (Uplevel DIC with Trip
Computer) on page 3-57.
2-17

When the doors are locked using the power door lock
switch of either front door, the red light, on top of
the instrument panel will start ashing to indicate the
system is arming. After all the doors are closed there will
be a time delay and then the red light will begin to
ash at a very slow rate indicating the sytem is armed.
Arming with the Remote Keyless
Entry Transmitter
The alarm system will arm when the remote keyless
entry transmitter is used to lock the doors after the key
is removed from the ignition. The red light will come
on to indicate that the system is arming. After all doors
are closed and locked, and after a time delay, the
red light will begin ashing at a very slow rate to show
the system is armed.
Arming Conrmation
A red light located on top of the instrument panel,
towards the center of the vehicle and near the
windshield, will ash slowly to conrm when the system
is armed.
Disarming with the Remote Keyless
Entry Transmitter
The alarm system will disarm when the remote keyless
entry transmitter is used to unlock the doors. The
red light will go out to show that the system is disarmed.
Disarming with Your Key
The alarm system will disarm when the key is used to
unlock the doors. The red light will stop ashing
when the system is disarmed. If you would like the key
to disarm the alarm system, see “Personal Programming
Mode Screens” underDIC Controls and Displays
(Base Level DIC) on page 3-49orDIC Controls and
Displays (Uplevel DIC with Trip Computer) on page 3-57
for more information.
PASS-Key®III
Your PASS-Key®III system operates on a radio
frequency subject to Federal Communications
Commission (FCC) Rules and with Industry Canada.
2-18

Ignition Positions
The ignition switch is located on the instrument panel,
to the right of the steering column.
There are four different
positions. Insert the key
in the ignition and turn
it to the right for each
position.
9(OFF):This position locks the ignition, steering
wheel and transaxle. It is a theft-deterrent feature. This is
the only position from which the key can be removed.
Notice:Using a tool to force the key from the
ignition switch could cause damage or break the
key. Use the correct key and turn the key only with
your hand. Make sure the key is all the way in. If
it is, turn the steering wheel left and right while you
turn the key hard. If none of this works, then
your vehicle needs service.ACC (ACCESSORY):This position allows things like
the radio and windshield wipers to operate while
the engine is off.
R(RUN):This position is where the key returns to
after the vehicle is started. With the engine off, the
RUN position displays some of the warning and
indicator lights.
/(START):This position starts the engine. Let go of
the key when the engine starts. The key will return
to the RUN position for normal driving.
A continuous warning chime will sound and a KEY IN
IGNITION warning message will display on the
Driver Information Center (DIC) if the key is in the
ignition in OFF or ACC and the driver’s door is opened.
Retained Accessory Power (RAP)
If the vehicle has Retained Accessory Power (RAP),
certain features will continue to operate for up to
10 minutes after the ignition key is turned to OFF unless
a door is opened.
2-22

The up-shift indicator light
on the instrument panel
cluster, or the up-shift
symbol on the Head-Up
Display (HUD), if equipped,
is given as a prompt to
use the TAP-Shift ™
paddle.
The up-shift indicator light will only appear in the
instrument panel cluster if the HUD is off or if the
vehicle does not have HUD.
This prompt to up-shift, as needed, will be given
throughout acceleration. If up-shifting does not occur
when prompted, the vehicle speed will be limited
to protect the engine.Press the accelerator while driving in the highest
gear (fourth gear) which is between 20 and 50 mph to
make the transaxle automatically down-shift. As
you’re speed gets closer to 50 mph, more effort will
be required to press the acclerator. At 50 mph, even
with the accelerator fully depressed, the transaxle
will always remain in the 4th gear. The transaxle will
also automatically down-shift as the vehicle decelerates
and comes to a stop.
When a paddle is pushed or pulled a chime will sound
when the vehicle cannot respond to a transaxle gear
change. The system will not allow either an up-shift or a
down-shift if the vehicle speed is too fast or too slow,
nor will it allow a start from THIRD (3) or higher gear.
The MANUAL (M) gear can also be selected while
the vehicle is already moving. The current transaxle
position will continue to be displayed on the Driver
Information Center (DIC) and HUD, if equipped.
2-29

Instrument Panel Overview...............................3-4
Hazard Warning Flashers................................3-5
Other Warning Devices...................................3-6
Horn.............................................................3-6
Tilt Wheel.....................................................3-6
Turn and Lane-Change Signals........................3-7
Headlamp High/Low-Beam Changer..................3-8
Flash-to-Pass.................................................3-8
Windshield Wiper Lever...................................3-9
Cruise Control..............................................3-10
Exterior Lamps.............................................3-14
Headlamps on Reminder................................3-15
Daytime Running Lamps (DRL).......................3-15
Fog Lamps..................................................3-16
Exterior Lighting Battery Saver........................3-17
Interior Lamps..............................................3-17
Instrument Panel Brightness...........................3-17
Courtesy Lamps...........................................3-18
Entry Lighting...............................................3-18
Delayed Entry Lighting...................................3-18
Delayed Exit Lighting.....................................3-19
Front Reading Lamps....................................3-19
Overhead Console Reading Lamps.................3-19
Rear Assist Handle Reading Lamps................3-19Battery Run-Down Protection..........................3-20
Head-Up Display (HUD).................................3-20
Accessory Power Outlets...............................3-24
Ashtrays and Cigarette Lighter........................3-25
Climate Controls............................................3-26
Climate Control System.................................3-26
Dual Automatic Climate Control System...........3-29
Outlet Adjustment.........................................3-33
Passenger Compartment Air Filter...................3-33
Warning Lights, Gages, and Indicators............3-35
Instrument Panel Cluster................................3-36
Speedometer and Odometer...........................3-37
Tachometer.................................................3-37
Safety Belt Reminder Light.............................3-38
Airbag Readiness Light..................................3-38
Up-Shift Light...............................................3-39
Brake System Warning Light..........................3-40
Anti-Lock Brake System Warning Light.............3-41
Traction Control System (TCS) Warning Light......3-42
Enhanced Traction System Warning Light.........3-42
Engine Coolant Temperature Warning Light......3-43
Engine Coolant Temperature Gage..................3-43
Malfunction Indicator Lamp.............................3-44
Section 3 Instrument Panel
3-1