key PONTIAC GRAND PRIX 2007 Service Manual

If the Light is Flashing
The following may prevent more serious damage
to your vehicle:
Reducing vehicle speed
Avoiding hard accelerations
Avoiding steep uphill grades
If you are towing a trailer, reduce the amount
of cargo being hauled as soon as it is
possible
If the light stops ashing and remains on steady,
see “If the Light Is On Steady” following.
If the light continues to ash, when it is safe to do
so, stop the vehicle. Find a safe place to park
your vehicle. Turn the key off, wait at least
10 seconds and restart the engine. If the light
remains on steady, see “If the Light Is On Steady”
following. If the light is still ashing, follow the
previous steps, and see your dealer for service as
soon as possible.
If the Light Is On Steady
You may be able to correct the emission system
malfunction by considering the following:
Did you recently put fuel into your vehicle?
If so, reinstall the fuel cap, making sure to fully
install the cap. SeeFilling the Tank on page 342.
The diagnostic system can determine if the
fuel cap has been left off or improperly installed.
A loose or missing fuel cap will allow fuel to
evaporate into the atmosphere. A few driving trips
with the cap properly installed should turn the
light off.
Did you just drive through a deep puddle of water?
If so, your electrical system may be wet. The
condition will usually be corrected when the
electrical system dries out. A few driving trips
should turn the light off.
182

ENGINE HOURS:This screen shows the number
of cumulative hours the engine has operated
while the key was in the RUN position. This screen
cannot be reset.
Press the gages button to advance to the next
screen.
ENGINE BOOST:If the vehicle has the
supercharged engine, this screen will appear.
It shows a graphic that indicates the amount of
boost the engine is receiving.
Press the gages button again to advance to the
next screen.
MAXIMUM Gs:If you have the GXP option, this
screen will appear. The DIC monitors and
keeps track of the maximum levels for
acceleration, deceleration, and lateral-acceleration
achieved since the screen was last reset. If you
try to select this screen while the vehicle is
moving, the message MAXIMUM Gs NOT
AVAILABLE WHILE MOVING will display. To view
the maximum accelerations achieved since last
reset, you must bring the vehicle to a stop.
Then the values will be displayed.To reset the values to zero, press and hold the
set/reset button.
Press the gages button again to advance to the
next screen.
Trip Odometer
3(Trip Odometer):Press this button to access
the Odometer, Trip Distances, AVERAGE
SPEED, and TIME ELAPSED modes.
Odometer:When the trip odometer button is
pressed, the rst menu displayed on the DIC
screen is the odometer reading, or cumulative
mileage of the vehicle. The odometer cannot be
reset.
Press the trip odometer button again to advance
to the next menu.
Trip Distances:This menu shows the distances
that the vehicle has driven between specic
points. The trip odometer will record the number of
miles up to 9,999.9 miles or 9 999.9 km travelled
for up to two trips. When 9,999.9 miles or
9 999.9 km is reached for either trip, the odometer
for that trip will go back to zero.
192

KEY FOB BATTERY LOW
This symbol comes on
with this message.
This message displays when the battery in the
Remote Keyless Entry (RKE) transmitter needs to
be replaced. To replace the battery, see “Battery
Replacement” underRemote Keyless Entry (RKE)
System Operation on page 87.
This message displays while the ignition is in
RUN. A chime sounds for two seconds when this
message is displayed. Press the set/reset
button to acknowledge this message and to clear
it from the screen.This message continues to display if it has not
been acknowledged when the engine is turned off.
It also re-displays for three seconds if the
message has been acknowledged, but the
condition still exists when the engine is turned off.
The message re-appears when the engine is
turned on and the condition still exists.
KEY IN IGNITION
This message displays and a chime sounds
continuously when the driver exits the vehicle while
the key is in the ignition after the engine is
turned off.
This message cannot be acknowledged.
This message disappears and the chiming stops
when the key is removed from the ignition.
208

A chime sounds continuously while this message
is displayed if driving above 5 mph (8 km/h).
Press the set/reset button to acknowledge this
message and to clear it from the screen.
This message continues to display for
three seconds if it has not been acknowledged
when the engine is turned off. It also re-displays for
three seconds if the message has been
acknowledged, but the condition still exists when
the engine is turned off.
If the condition still exists, the message re-appears
when the engine is turned on.
PARK LAMPS ON
This message displays to alert the driver when the
parking lamps are on, the ignition is in OFF,
and the key is removed. A chime sounds
continuously while this message is displayed. This
message cannot be acknowledged.
REDUCED ENGINE POWER
This symbol comes on
with this message.
This message displays when the vehicle’s engine
power is reduced. If this happens during driving
conditions, such as climbing a steep hill, the
transaxle may overwork in a gear that may cause
damage to the vehicle’s engine or transaxle.
Reduced engine power can affect the vehicle’s
ability to accelerate. If this message is on,
but there is no reduction in performance, proceed
to your destination. The performance may be
reduced the next time the vehicle is driven. The
vehicle may be driven at a reduced speed
while this message is on, but acceleration and
speed may be reduced. Anytime this message
stays on, the vehicle should be taken to your
dealer for service as soon as possible.
214

This message displays only when the ignition is in
RUN. A chime sounds for two seconds while
this message is displayed. Press the set/reset
button to acknowledge this message and to clear
it from the screen.
This message continues to display if it has not
been acknowledged when the engine is turned off.
It also re-displays for three seconds if the
message has been acknowledged, but the
condition still exists when the engine is turned off.
If the condition still exists, the message
re-appears when the engine is turned on.
REMOTE START ACTIVE PRESS
HAZARD SWITCH TO CANCEL
If your vehicle has the remote start feature, this
message displays when a remote start is initiated.
If you would like to cancel the remote start, turn
on the hazard warning ashers. SeeHazard
Warning Flashers on page 134.
REMOTE START DISABLED
If your vehicle has the remote start feature, this
message displays if a remote start attempt is
unsuccessful. This may be caused if any of the
following conditions are true when a remote
start attempt is made:
The remote start system is disabled through
the DIC.
The key is in the ignition.
The hood or the doors are not closed.
There is an emission control system
malfunction.
The engine coolant temperature is too high.
The oil pressure is low.
The hazard warning ashers are turned on.
The maximum number of remote starts
or remote start attempts between ignition
cycles has been reached.
The content theft-deterrent alarm is on while
attempting to remote start the vehicle.
See “REMOTE START” underDIC Vehicle
Customization on page 226and “Remote Vehicle
Start” underRemote Keyless Entry (RKE) System
Operation on page 87for more information.
215

SERVICE THEFT SYSTEM
This message displays if there is a problem with
the theft-deterrent system programmed in the key.
A fault has been detected in the system which
means that the system is disabled and it is
not protecting the vehicle. The vehicle usually
restarts; however, you may want to take the
vehicle to your dealer before turning off the engine.
SeeKeys on page 84for information on the
PASS-Key
®III system.
This message displays only while the ignition is in
RUN. A chime sounds for two seconds while
this message is displayed. Press the set/reset
button to acknowledge this message and to clear
it from the screen.
This message continues to display if it has not
been acknowledged when the engine is turned off.
It also re-displays for three seconds if the
message has been acknowledged, but the
condition still exists when the engine is turned off.
If the condition still exists, the message
re-appears when the engine is turned on.
SERVICE TIRE MONITOR SYSTEM
This message displays if a part on the Tire
Pressure Monitor (TPM) system is not working
properly. If you drive your vehicle while any of the
four sensors are missing or inoperable, the
warning comes on in about 20 minutes. A sensor
would be missing, for example, if you put
different wheels on your vehicle without
transferring the sensors. If the warning comes on
and stays on, there may be a problem with the
TPM. See your dealer.
This message displays only while the ignition is in
RUN. Press the set/reset button to acknowledge
this message and to clear it from the screen.
This message continues to display if it has
not been acknowledged when the engine is turned
off. It also re-displays for three seconds if the
message has been acknowledged, but the
condition still exists when the engine is turned off.
If the condition still exists, the message
re-appears when the engine is turned on.
220

Entering the Personal Programming Mode
1. Turn the ignition on and make sure the
vehicle is in PARK (P).
To avoid excessive drain on the battery, it is
recommended that the headlamps are
turned off.
2. Press the options button until PERSONAL
PROGRAMMING MODE appears on the DIC.
3. Press the set/reset button to display the rst
screen.
4. Press the options button to access these
modes:
Personal Programming Mode Screens
EXTERIOR LIGHTING DELAY:This screen
allows this feature to be turned off, or allows the
selection of the number of seconds the headlamps,
sidelamps, taillamps, fog lamps, and back-up
lamps are turned on after the key is removed from
the ignition, or the vehicle is unlocked using the
remote keyless entry transmitter.
If OFF is selected, the exterior lamps will not
turn on.If a time delay is chosen, the lamps will turn on for
the selected time. The time delay will be
cancelled and the exterior lamps will turn on
automatically when the key is removed from the
ignition, or the vehicle is unlocked using the
remote keyless entry transmitter.
To program this mode, use the following
procedure:
1. Press and release the set/reset button to
scroll to the selection you want to program.
Choose from OFF, 15, 30, 60, or 90 seconds.
2. Press the options button again to advance to
the next screen.
INTERIOR LIGHTS WHEN DOOR CLOSED:This
screen allows this feature to be turned OFF or ON.
If OFF is selected, the interior lamps will turn off
immediately when the ignition is turned off and the
last open door is closed.
If ON is selected, the interior lamps will stay on for
about 25 seconds after the vehicle’s ignition is
turned off and the last open door is closed.
227

To program this mode, use the following procedure:
1. Press and release the set/reset button to
scroll to either OFF or ON.
2. Press the options button again to advance to
the next screen.
INTERIOR LIGHTS WHEN KEY REMOVED:This
screen allows this feature to be turned OFF or
ON. This feature enables the interior lamps in the
vehicle to turn on for about 25 seconds after
the key is removed from the ignition.
If OFF is selected, removing the key from the
ignition will not cause the interior lamps to turn on.
If ON is selected, removing the key from the
ignition will cause the interior lamps to be turned
on for about 25 seconds.
To program this mode, use the following
procedure:
1. Press and release the set/reset button to
scroll to either OFF or ON.
2. Press the options button again to advance to
the next screen.AUTO DOOR UNLOCK:This screen allows this
feature to be turned off, used for the driver’s
door only, or for all the doors.
If OFF is selected, none of the doors will unlock
when the vehicle’s transaxle is shifted into
PARK (P).
If DRIVER is selected, only the driver’s door will
unlock when the vehicle’s transaxle is shifted
into PARK (P).
If ALL is selected, all the doors will unlock when
the vehicle’s transaxle is shifted into PARK (P).
To program this mode, use the following
procedure:
1. Press and release the set/reset button to
scroll to either OFF, DRIVER, or ALL.
2. Press the options button again to advance to
the next screen.
228

AUTO DOOR UNLOCK ON:If DRIVER or ALL
was selected on the AUTO DOOR UNLOCK
screen, this screen allows selection of when the
vehicle’s doors will unlock. The choices are
when the key is removed from the ignition or when
the vehicle is shifted into PARK (P).
If KEY-OUT is selected, the auto door unlock will
function when the key is taken out of the
ignition.
If PARK is selected, the auto door unlock will
function when the transaxle is shifted into
PARK (P).
To program this mode, use the following
procedure:
1. Press and release the set/reset button to
scroll to either KEY-OUT or PARK.
2. Press the options button again to advance to
the next screen.DELAYED LOCKING:This screen allows this
feature to be turned OFF or ON. The key must be
out of the ignition for this feature to work.
If OFF is selected, there will be no delayed locking
of the vehicle’s doors.
If ON is selected, the locking of the vehicle’s
doors will be delayed by ve seconds after
a power door lock switch is pressed while the door
is open, or the LOCK button on the remote
keyless entry transmitter is pressed while any door
is open.
To program this mode, use the following
procedure:
1. Press and release the set/reset button to
scroll to either OFF or ON.
2. Press the options button again to advance to
the next screen.
229

REMOTE LOCKS FEEDBACK:This screen
allows selection for this option to be turned OFF,
or gives the choice of two methods of verication;
LIGHTS or LIGHTS and HORN; that indicate
the vehicle’s doors are locked when the LOCK
button on the remote keyless entry transmitter is
pressed.
If OFF is selected, this feature will not be
programmed.
If LIGHTS is selected, the exterior lamps will ash
when the LOCK button on the remote keyless
entry transmitter is pressed.
If LIGHTS and HORN is selected, the exterior
lamps will ash when the LOCK button on
the remote keyless entry transmitter is pressed,
and the horn will sound when the LOCK button on
the remote keyless entry transmitter is pressed
again within ve seconds of the previous
command.To program this mode, use the following
procedure:
1. Press the set/reset button to scroll to OFF,
LIGHTS, or LIGHTS and HORN.
2. Press the options button again to advance to
the next screen.
If the vehicle does not have a content
theft-deterrent system, the next screens with
PROGRAMMING FINISHED and DISPLAY OFF
will appear.
If the vehicle does have a content theft-deterrent
system, the next screen will appear.
THEFT DETERRENT:The vehicle may have a
content theft-deterrent system. Once it is
turned on, the system will activate if someone tries
to enter the vehicle without using the remote
keyless entry transmitter or the correct key. This
screen allows this feature to be turned OFF or ON.
If OFF is selected, the content theft-deterrent
system will not function.
If ON is selected, the content theft-deterrent
system will be activated.
230