PONTIAC VIBE 2009 Manual Online

Instruments and
Controls
Instrument Panel
Overview
Instrument Panel
Overview...........................4-2
Hazard Warning Flashers. . . .4-3
Horn...................................4-3
Tilt Wheel...........................4-4
Turn Signal/Multifunction
Lever................................4-4
Cruise Control....................4-4
Turn and Lane-Change
Signals.............................4-7
Headlamp High/
Low-Beam Changer..........4-7
Flash-to-Pass......................4-7
Windshield Wipers..............4-7
Windshield Washer.............4-8
Rear Window Wiper/
Washer.............................4-8
Accessory Power
Outlet(s)............................4-9
Power Outlet 115 Volt
Alternating Current..........4-10
Ashtray(s).........................4-10
Warning Lights, Gages,
and Indicators
Warning Lights, Gages,
and Indicators.................4-11
Instrument Panel Cluster. . .4-12
Speedometer and
Odometer........................4-13
Trip Odometer(s)...............4-13
Tachometer.......................4-13
Safety Belt Reminders......4-14
Airbag Readiness Light.....4-14
Passenger Airbag Status
Indicator..........................4-15
Service Airbag Notication
System Message.............4-16
Charging System Light......4-16
Brake System Warning
Light................................4-17
Antilock Brake System
(ABS) Warning Light.......4-18
Speed Sensitive Power
Steering (SSPS)
Warning Light
..................4-18
Low Tire Pressure
Warning Light..................4-18
Traction Control System
(TCS) Warning Light.......4-19
StabiliTrak®Indicator
Light................................4-19
Engine Coolant
Temperature Gage..........4-19
Malfunction
Indicator Lamp................4-20
Security Light....................4-22
Oil Pressure Light.............4-22
Fog Lamp Light................4-23
Lights On Reminder..........4-23
Taillamp Indicator Light.....4-23
Cruise Control Light..........4-23
Low Washer Fluid
Warning Light..................4-23
Service All-Wheel Drive
Light................................4-24
Highbeam On Light...........4-24
Door Ajar Light.................4-24
Fuel Gage........................4-24
Low Fuel Warning Light. . . .4-25
OnStar®System
OnStar®System................4-25
Instruments and Controls 4-1
2009 - Pontiac Vibe Owner Manual

Instrument Panel Overview
4-2 Instruments and Controls
2009 - Pontiac Vibe Owner Manual

The main components of the
instrument panel are the following:
A.Outside Power Mirror(s) on
page 2-14.
B.Outlet Adjustment on page 7-3.
C.Turn Signal/Multifunction
Lever on page 4-4.
D.Instrument Panel Cluster on
page 4-12.
E.Windshield Wipers on page 4-7.
F. Passenger Airbag Status
Indicator.Passenger Sensing
System on page 1-28.
Security Light. SeeContent
Theft-Deterrent on page 2-10.
G.Hazard Warning Flashers on
page 4-3.
H.Audio System(s) on page 6-1.
I.Traction Control System (TCS)
on page 8-21.
J.Content Theft-Deterrent on
page 2-10.
K.Driver Storage Compartment
on page 3-3.
L.Hood Release on page 9-5.M.Audio Steering Wheel Controls
on page 6-13.
N.Tilt Wheel on page 4-4.
O.Horn on page 4-3.
P.Cruise Control on page 4-4
(If Equipped).
Q.Ignition Positions on page 8-2.
R. Tire Pressure Reset Button
(Out of View). SeeTire Pressure
Monitor Operation on page 9-50.
S.Power Outlet 115 Volt Alternating
Current on page 4-10On/Off
Button.
T. Cigarette Lighter (If Equipped)
or Accessory Power Outlet.
Ashtray(s) on page 4-10
orAccessory Power Outlet(s)
on page 4-9.
U. Shift Lever.Automatic
Transmission Operation
(Four Speed) on page 8-6or
Automatic Transmission
Operation (Five Speed)
on page 8-8orManual
Transmission Operation
on page 8-11.V.Power Outlet 115 Volt Alternating
Current on page 4-10.
W.Climate Control System on
page 7-1.
X.Hooks on page 3-3
.
Y.Glove Box on page 3-1.
Hazard Warning Flashers
|
(Hazard Warning Flasher):
Press this button located on
the instrument panel, to make the
front and rear turn signal lamps ash
on and off. This warns others that
you are having trouble.
Press
|again to turn the
ashers off.
Horn
Press near or on the horn symbols
on the steering wheel pad to
sound the horn.
Instruments and Controls 4-3
2009 - Pontiac Vibe Owner Manual

Tilt Wheel
A tilt and telescope wheel lets the
steering wheel position be adjusted.
The adjustment lever is located
on the left side of the steering
column.
Pull the lever down to move the
steering wheel up or down and in or
out. Pull the lever up to lock the
steering wheel in place.
Do not adjust the tilt and telescope
lever while driving.
Turn Signal/Multifunction
Lever
The lever on the left side of the
steering column includes the
following:
O:Exterior Lamps.
G:Turn and Lane-Change
Signals.
2:Headlamp High/Low-Beam
Changer.
#:Fog Lamps (If Equipped).
Flash-to-Pass Feature.
Information for these features is on
the pages following.
Cruise Control
For vehicles with cruise control, the
lever is located on the right side
of the steering wheel.
Cruise control, lets a speed of
25 mph (40 km/h) or more be
maintained without keeping your
foot on the accelerator. Cruise
control does not work at speeds
below 25 mph (40 km/h).
4-4 Instruments and Controls
2009 - Pontiac Vibe Owner Manual

{CAUTION
Cruise control can be dangerous
where you cannot drive safely at
a steady speed. So, do not use
the cruise control on winding
roads or in heavy traffic.
Cruise control can be dangerous
on slippery roads. On such roads,
fast changes in tire traction can
cause excessive wheel slip, and
you could lose control. Do not use
cruise control on slippery roads.Setting Cruise Control{CAUTION
If you leave your cruise control on
when you are not using cruise,
you might hit a button and go into
cruise when you do not want to.
You could be startled and even
lose control. Keep the cruise
control switch off until you want to
use cruise control.
1. Press the ON-OFF button at the
end of the lever. The CRUISE
light on the instrument panel
cluster comes on. SeeCruise
Control Light on page 4-23.
2. Get to the desired speed.
3. Move the lever down to−SET
and release it.
4. Take your foot off the accelerator
pedal.If the cruise control indicator light
ashes, press the ON-OFF button
once to deactivate the system, and
then press the button back on.
If the cruise control speed cannot be
set or the cruise control cancels
immediately after being activated,
there may be a problem with the
cruise control system. See your
dealer/retailer.
Resuming a Set Speed
If the brakes are applied after the
cruise control is set, the cruise
control is turned off.
If the vehicle speed is 25 mph
(40 km/h) or greater, push the lever
up to +RES (Resume/Accelerate)
to return to the previously set speed.
Instruments and Controls 4-5
2009 - Pontiac Vibe Owner Manual

Increasing Speed While Using
Cruise Control
There are three ways to increase
the vehicle speed:
Use the accelerator pedal to get
to the higher speed. Move the
lever down to−SET. Release the
lever and the accelerator pedal.
Move the cruise lever up
to +RES. Hold it there until the
desired speed is reached,
and then release the lever.
To increase the vehicle speed in
very small amounts, move the
lever to +RES briey and then
release it. Each time this is done,
the vehicle goes about 1 mph
(1.6 km/h) faster.Reducing Speed While Using
Cruise Control
There are two ways to reduce the
vehicle speed while using cruise
control:
Push and hold the lever to−SET
until the desired lower speed is
reached, then release it.
To slow down in very small
amounts, push the lever
down briey. Each time this
is done, the vehicle will go about
1 mph (1.6 km/h) slower.
Passing Another Vehicle While
Using Cruise Control
Use the accelerator pedal to
increase the vehicle speed.
When you take your foot off the
pedal, the vehicle slows down to
the cruise control speed set earlier.
Using Cruise Control on Hills
The cruise control performance will
vary depending upon the vehicle
speed, load, and the steepness of
the hills.When going up steep hills, you might
have to step on the accelerator pedal
to maintain the vehicle speed.
When going downhill, you might
have to brake or shift to a lower gear
to keep the vehicle speed down.
Applying the brake or downshifting
to 2 SECOND or L LOW turns
off the cruise control.
Ending Cruise Control
There are several ways to turn off
the cruise control:
Step on the brake pedal or push
the clutch pedal, if the vehicle
has a manual transmission.
Press the ON-OFF button.
Pull the cruise control lever
toward you.
Erasing Speed Memory
The cruise control set speed memory
is erased when the cruise control or
the ignition is turned off.
4-6 Instruments and Controls
2009 - Pontiac Vibe Owner Manual

Turn and Lane-Change
Signals
An arrow on the instrument panel
cluster ashes in the direction of the
turn or lane change.
Move the lever all the way up or
down to signal a turn.
Raise or lower the lever until the
arrow starts to ash to signal a lane
change. Hold it there until the
lane change is completed.
The lever returns to its starting
position whenever it is released.
If after signaling a turn or a
lane change the arrow ashes
rapidly or does not come on,
a signal bulb may be burned out.
Have the bulbs replaced. If the bulb
is not burned out, check the fuse.
SeeFuses and Circuit Breakers
on page 9-36.
Headlamp High/
Low-Beam Changer
The headlamps must be on for this
feature to work.
Push the turn signal lever away
from you to turn the high beams on.
This instrument panel cluster light
3comes on while the high beam
headlamps are on.
Pull the lever towards you to return
to low beams.
Flash-to-Pass
This feature is used to signal to the
vehicle ahead that you want to pass.
With the lever in the low-beam
position, pull the lever toward you to
momentarily switch to high-beams.
If the headlamps are on when the
lever is released, the high-beams will
return to low-beam.
Windshield Wipers
The windshield wiper/washer lever
is located on the right side of
the steering column.
Move the lever to one of the
following positions:
z(Mist):Move the lever to mist,
for a single wiping cycle and then
release. The wipers stop after
one wipe.
((Off):Move the lever to this
position to turn the wipers off.
Instruments and Controls 4-7
2009 - Pontiac Vibe Owner Manual

&(Intermittent):Move the lever
to choose a delayed wiping cycle.
For vehicles with the variable
intermittent feature, the time
between wipes can be adjusted.
Turn the
&band for a longer
or shorter delay interval.
q(Low):Use for steady wiping at
low speed.
l(High):Use for steady wiping at
high speed.
Clear snow and ice from the wiper
blades before using them. If the
blades are frozen to the windshield,
loosen or thaw them. If they
become damaged, get new blades
or blade inserts. SeeWindshield
Wiper Blade Replacement on
page 9-25.
Heavy snow or ice can overload the
wipers. A circuit breaker stops
them until the motor cools.
Windshield Washer
Pull the lever toward you to spray
washer uid on the windshield.
The spray continues until the lever
is released. The wipers will run
a few times. SeeWindshield Washer
Fluid on page 9-24for information
on lling the windshield washer uid
reservoir.
{CAUTION
In freezing weather, do not use
your washer until the windshield
is warmed. Otherwise the
washer uid can form ice on the
windshield, blocking your vision.
Rear Window
Wiper/Washer
Z
Rear Wiper:Turn the end of
the lever to low or high, to turn
on the rear window wiper.
y(Low):For steady rear wiping at
low speed.
x(High):For steady rear wiping
at high speed.
=(Rear Washer):Turn the end
of the lever up or down as far
as it will go, to squirt washer uid
on the rear window. The knob
automatically returns from these
positions after it is released.
The windshield washer reservoir is
used for the windshield and the
rear window. Check the uid level
in the reservoir if either washer
is not working. SeeWindshield
Washer Fluid on page 9-24.
4-8 Instruments and Controls
2009 - Pontiac Vibe Owner Manual

{CAUTION
In freezing weather, do not use
your washer until the windshield
is warmed. Otherwise the
washer uid can form ice on the
windshield, blocking your vision.
Accessory Power
Outlet(s)
Accessory power outlets can be
used to plug in auxiliary electrical
equipment.
The vehicle has an accessory
power outlet on the center oor
console below the shift lever.
To use the outlet, the ignition
must be in ON/RUN or
ACC/ACCESSORY. Pull down the
small cover to access the outlet.Notice:Leaving electrical
equipment on for extended
periods will drain the battery.
Always turn off electrical
equipment when not in use and
do not plug in equipment that
exceeds the maximum amperage
rating.
This circuit is protected by a fuse
and has a maximum current level.
Do not use equipment exceeding
the maximum amperage rating.
Certain power accessory plugs may
not be compatible to the power
accessory outlet and could result
in a blown vehicle or adapter
fuse. See your dealer/retailer for
additional information on the power
accessory plugs.Notice:Adding any electrical
equipment to the vehicle can
damage it or keep other
components from working as
they should. The repairs would
not be covered by the vehicle
warranty. Do not use equipment
exceeding maximum amperage
rating of 20 amperes. Check
with your dealer/retailer before
adding electrical equipment.
When adding electrical equipment,
be sure to follow the proper
installation instructions included
with the equipment.
Notice:Improper use of the
power outlet can cause damage
not covered by the warranty.
Do not hang any type of
accessory or accessory bracket
from the plug because the
power outlets are designed for
accessory power plugs only.
Instruments and Controls 4-9
2009 - Pontiac Vibe Owner Manual

Power Outlet 115 Volt
Alternating Current
Electrical equipment with a
maximum limit of 115 VAC can be
plugged into this power outlet. If the
equipment used requires more than
the limit, a protection circuit will
cut the power supply. The power
automatically restarts when
equipment that operates within
the limit is plugged in.
The power outlet is located below
the shift lever.
Before using the outlet, turn on
the ignition and press the button
located on the instrument panel
below the climate control system.An indicator light in the button
comes on. After using the outlet,
press the button again to turn it off.
The power outlet is not designed for
the following electrical equipment
and they may not work properly:
Equipment with high initial peak
wattage: cathode-ray tube type
televisions, compressor-driven
refrigerators, or electric
power tools.
Other equipment requiring an
extremely stable power supply:
microcomputer-controlled
electric blankets, touch sensor
lamps, etc.
Ashtray(s)
For vehicles with a removable
ashtray, it is located in the front
cupholder in the center console
storage area.
Notice:If papers, pins, or other
ammable items are put in
the ashtray, hot cigarettes or
other smoking materials could
ignite them and possibly damage
the vehicle. Never put ammable
items in the ashtray.
For vehicles with a lighter, push
the lighter down and it will pop up
when it is ready to be used.
The ignition switch must be in the
ACC/ACCESSORY or ON/RUN
position to use the lighter.
4-10 Instruments and Controls
2009 - Pontiac Vibe Owner Manual