PORSCHE 911 TURBO 2014 6.G Owners Manual

Minor Repairs 279
Towing a vehicle on one axle:
Raising an axle, irrespective of whether at the front or rear, is only permissible if the drive shaft (cardan shaft) has been removed beforehand. The ignition must be switched off.fThe vehicle must not be towed if the PDK transmission is in emergency operation mode (yellow or red “ Transm. failure Park vehicle safely ” warning message). The vehicle must be transported with a car transporter or on a trailer.fIf a selector lever emergency release was performed, the vehicle must not be towed. The vehicle must be transported with a car transporter or on a trailer.fMove PDK selector lever to position N. To properly engage selector-lever position N on the display and at the selector lever, the engine must be started once before towing the vehicle. The vehicle can be towed as soon as the selector lever is in position N and selector- lever position N appears on the display.fSwitch ignition off. The ignition key must remain in the ignition lock so that the steering lock does not engage.The control unit must be removed from the ignition lock and the key inserted in vehicles with Porsche Entry & Drive. fPlease see the chapter “EMERGENCY OPERATION – UNLOCKING THE IGNITION KEY/CONTROL UNIT” on page 28.fMake sure that the vehicle is adequately illuminated.
fDo not exceed a maximum speed of 30 mph (50 km/h).Maximum towing distance 30 miles (50 km).If towing distances are greater, the vehicle must be transported with a car transporter or on a trailer.
Pulling out a vehicle stuck in snow, sand, etc.
fAlways pull out the stuck vehicle with the greatest care.fDo not pull out the vehicle abruptly or at an angle. fIf possible, pull the vehicle out backwards in its own tracks.
PDK selector lever emergency release
In the event of an electronics failure, emergency release of the selector lever must be performed in order to move the selector-lever to the N position.
Releasing selector lever
1. Take the plastic wedge from the toolbox. 2. Carefully lever out the rear part of the selector lever gate A on both sides (arrows) using the plastic wedge.3. Carefully lever out the front part of the switch panel B on both sides (arrow) using the plastic wedge.4. Remove the switch module B and place aside. The cable C of the switch panel must not be under tension.
14_991_Turbo_21.book Seite 279 Mittwoch, 9. April 2014 2:19 14

280 Minor Repairs
5.Push the selector lever lock downwards and hold, then move the selector lever into the N position.
Installing the switch panel and selector lever gate
1. Make sure that the cable clip D engages correctly in the selector support. Then engage the switch panel B into the front guides, fully insert the panel and press downwards until it engages securely.2. Press down the selector lever gate A until it engages securely.
Towing lug
The towing lug is stored in the left tool box in the luggage compartment.
fUse the towing lug only for an emergency to remove the vehicle off the road. The towing lug is to be used only to pull the vehicle onto the flat bed, tractor or towing apparatus if the vehicle will roll freely. Under no circumstances is the vehicle to be secured using the towing lug.fNever use the towing lug to tow this or any other vehicle.fBear in mind the limited ground clearance of your car on uneven surfaces,
Fitting the towing lug
When fitting on the rear of the vehicle, the license plate must be removed.
NOTICE
14_991_Turbo_21.book Seite 280 Mittwoch, 9. April 2014 2:19 14

Minor Repairs 281
1.Press the lower edge of the appropriate plastic cover into the bumper until the cover disengages.2. Pull cover out of the bumper and let it hang by its thread.3. Screw in towing lug A as far as it will go (left-hand thread) and tighten hand-tight.
Front towing lug
Removing the towing lug
1. Unscrew the towing lug A. 2. Insert plastic cover at the lower edge of the opening.3. Fold the cover up and press on its upper edge to engage it in the bumper.4. Store the towing lug in the tool box.
Pulling vehicle onto flat bed
1.Position wooden ramps at the base of the flat bed to reduce the angle of the pull.2. Reel in the hoist cable and check the underside of the vehicle for any interference.
14_991_Turbo_21.book Seite 281 Mittwoch, 9. April 2014 2:19 14

282 Minor Repairs
Tying down vehicle on flat bed
1.Carefully feed towing straps through the opening in the rear wheels. Make sure metal parts of straps do not damage rim.Make sure the strap is flat over the rim bead.Make sure brake backing plate is not damaged.2. Secure straps to rear of flat bed. 3. Reel in hoist cable only far enough to tension tie-down straps.
Transporting the vehicle on car trains, ferries and car transporters
fTie the vehicle down only at its wheels.fDeactivate interior surveillance and the inclination sensor.fPlease see the chapter “ALARM SYSTEM AND PASSENGER COMPARTMENT MONITORING” on page 216.
Fire extinguisher
In cars with a fire extinguisher, the extinguisher is located under the front passenger seat.fTo remove the fire extinguisher in case of an emergency, hold the extinguisher with one hand and press the button PRESS on the fire extinguisher holder with the other hand ( arrow).
Information
fCheck the final inspection date on the fire extinguisher. If the fire extinguisher is used after its inspection interval has elapsed, it may not work properly.fAlways read the operating instructions on the fire extinguisher.fObserve the fire extinguisher manufacturer’s safety instructions on the label at the fire extinguisher handle.fThe fire extinguisher should be checked to ensure correct operation by a specialist workshop every 1-2 years.fHave the fire extinguisher refilled after use.
14_991_Turbo_21.book Seite 282 Mittwoch, 9. April 2014 2:19 14

Tire Pressure and Technical Data 283
Tire Pressure and Technical Data
Vehicle Identification Data ............................284 Engine Data ................................................285Driving Performance....................................285Wheels, Tires ..............................................286Tire Pressure for Cold Tires (68 °F/ 20 °C) ...287Weights ......................................................288Dimensions.................................................288Filling Capacities .........................................289
Reifendruck_TechnischeDaten.fm Seite 283 Mittwoch, 9. April 2014 3:12 15

284 Tire Pressure and Technical Data
Vehicle identification number
Vehicle Identification Data
When ordering spare parts or making inquiries, always quote the vehicle identification number.
Vehicle identification number
You will find the vehicle identification number at the bottom left behind the windshield and under the front passenger’s seat.
Safety compliance sticker
Safety compliance sticker
The safety compliance sticker is your assurance that your new Porsche complies with all applicable Federal Motor Vehicle Safety Standards which were in effect at the time the vehicle was manufactured.
The sticker also shows the month and year of production and the vehicle identification number of your car (perforations) as well as the Gross Vehicle Weight Rating and the Gross Axle Weight Rating.
Tire pressure plate
Tire pressure plate
The plate is attached to the door aperture area on the driver’s side.
Vehicle data carrier
You will find the vehicle data carrier in the “Maintenance” booklet. It contains all important data about your vehicle.This data carrier cannot be re-ordered if it is lost or damaged.
Reifendruck_TechnischeDaten.fm Seite 284 Mittwoch, 9. April 2014 3:12 15

Tire Pressure and Technical Data 285
Engine Data
Driving Performance
The specifications refer to a vehicle with DIN curb weight without performance-reducing additional equipment (e.g. special tires).
911 Turbo911 Turbo S
Number of cylinders 6 6
Displacement 231.9 cu. in. (3,800 cm3)231.9 cu. in. (3,800 cm3)
Max. engine power as per 80/1269/EEC 520 hp (338 kW) 560 hp (412 kW)
At engine speed 6,000-6,500 rpm 6,500-6,750 rpm
Max. torque as per 80/1269/EEC487 ftlb. (660 Nm)Overboost: 524 ftlb. (710 Nm)553 ftlb. (700 Nm)Overboost: 553 ftlb. (750 Nm)
At engine speed1,950-5,000 rpmOverboost: 2,100-4,250 rpm2,100-4,250 rpmOverboost: 2,200-4,000 rpm
Maximum permitted engine speed 7,000 rpm 7,200 rpm
Maximum track speedAcceleration 0–100 km/h (62 mph) (values in bracketsrelate to “Sport Plus” mode)
911 Turbo Coupé196 mph (315 km/h) 3.4 (3.2) seconds
911 Turbo S Coupé198 mph (318 km/h) (3.1) seconds
911 Turbo Cabriolet196 mph (315 km/h) 3.5 (3.3) seconds
911 Turbo S Cabriolet198 mph (318 km/h) (3.2) seconds
Reifendruck_TechnischeDaten.fm Seite 285 Mittwoch, 9. April 2014 3:12 15

286 Tire Pressure and Technical Data
Wheels, Tires
fApproval of tire and wheel sizes is granted based on extensive testing. By fitting tires that have been approved by Porsche, you can be sure that you have the best possible tires for your Porsche.The load capacity coefficient (e.g. “91”) and maximum speed code letter (e.g. “Y”) for permitted top speed are minimum requirements. When fitting new tires or changing tires: Please see the chapter “TIRES AND WHEELS” on page 244.fSnow chain clearance can only be guaranteed with the tires marked 1). Snow chains can only be fitted on the rear wheels. Observe state or province-specific laws regarding maximum speeds with fitted snow chains. Only use Porsche approved fine-link cross-type or edge chains.fYour Porsche dealer will be pleased to advise you about the current approval status for tires, wheels and snow chains.
FA = front axle, RA = rear axle
20-inch wheel FA / RA5 holes and central lock8.5J x20, RO51 / 11J x20, RO56 1)9J x20, RO51 / 11.5J x20, RO56
Summer tires FA / RA245/35 ZR 20 (91Y) / 305/30 ZR 20 (103Y) XL 245/35 ZR 20 (91Y) / 305/30 ZR 20 (103Y) XL
Snow tires FA / RA245/35 R 20 91V / 295/30 R 20 97V 1)
20-inch wheel FA / RA Winter wheel with central lock8.5J x20, RO51 / 11J x20, RO59 1)
20-inch winter wheel FA / RA, 5-holenot for Turbo S,
not for vehicles with PCCB brake
8.5J x20, RO51 / 11J x20, RO52
Winter tires FA / RA245/35 R 20 91V / 295/30 R 20 97V
Installation of sizes not authorized by Porsche may impair driving stability and could result in loss of control of the vehicle.fBefore mounting new tires check with your authorized Porsche dealer for a current list of approved tires.
Improper Tire SizeDANGERh
Reifendruck_TechnischeDaten.fm Seite 286 Mittwoch, 9. April 2014 3:12 15

Tire Pressure and Technical Data 287
Tire Pressure for Cold Tires (68 °F/ 20 °C)
These standard and comfort tire pressures apply only to the tire makes and types approved by Porsche.
Standard tire pressure for summer tires
fThe load condition of the vehicle must be set and comfort pressure/standard pressure selected on the multi-function display. The tire pressure must be changed according to the vehicle load. Please see the chapter “SELECTING LOAD IN THE TPMS MENU” on page 110.
Standard tire pressure for snow tires
fThe load condition of the vehicle must be set on the multi-function display. The tire pressure must be changed according to the vehicle load. Please see the chapter “SELECTING LOAD IN THE TPMS MENU” on page 110.
Comfort tire pressure for summer tires up to 165 mph (270 km/h)
The comfort tire pressure speed threshold permitted for your vehicle depends on the national type standardization and is displayed under “Comfort pressure” in the “Tire pressure” menu on the multi-function display.fThe load condition of the vehicle must be set on the multi-function display. The tire pressure must be changed according to the vehicle load. Please see the chapter “SELECTING LOAD IN THE TPMS MENU” on page 110.Please see the chapter “SELECTING COMFORT/STANDARD PRESSURE IN THE TPMS MENU” on page 110.
FA = front axle, RA = rear axle
Part load Full load
FA R A FA R A
911 Turbo, 911 Turbo S34 psi/2.4 bar/240 kPa
43 psi/3.0 bar/300 kPa
37 psi/2.6 bar/260 kPa
47 psi/3.3 bar/330 kPa
Part loadFull load
FA R A FA R A
911 Turbo, 911 Turbo S31 psi/2.2 bar/220 kPa
39 psi/2.7 bar/270 kPa
34 psi/2.4 bar/240 kPa
43 psi/3.0 bar/300 kPa
Part loadFull load
FA R A FA R A
911 Turbo, 911 Turbo S31 psi/2.2 bar/220 kPa
36 psi/2.5 bar/250 kPa
33 psi/2.3 bar/230 kPa
40 psi/2.8 bar/280 kPa
Reifendruck_TechnischeDaten.fm Seite 287 Mittwoch, 9. April 2014 3:12 15

288 Tire Pressure and Technical Data
Weights
1) Curb weight includes 165 lbs. (75 kg) driver and baggage share.2) The maximum vehicle weight and maximum axle loads must not be exceeded.Notice: If additional accessories are installed, the maximum load will be correspondingly less.3) Only use Roof Transport Systems from the Porsche Tequipment product range for your car or Roof Transport Systems that have been tested and approved by Porsche.
Dimensions
911 Turbo Coupé 911 Turbo S Coupé 911 Turbo Cabriolet 911 Turbo S Cabriolet
Empty weight (depending on equipment) per DIN 700203,516 lbs. to 3,704 lbs.(1,595 kg to 1,680 kg)3,538 lbs. to 3,704 lbs.(1,605 kg to 1,680 kg)3,814 lbs. to 3,671 lbs.(1,665 kg to 1,730 kg)3,814 lbs. to 3,693 lbs.(1,675 kg to 1,730 kg)
Empty weight (depending on equipment)per 70/156/EEC1)3,682 lbs. to 3,869 lbs.(1,670 kg to 1,755 kg)3,704 lbs. to 3,869 lbs.(1,680 kg to 1,755 kg)3,836 lbs. to 3,979 lbs.(1,740 kg to 1,805 kg)3,858 lbs. to 3,979 lbs.(1,750 kg to 1,805 kg)
Maximum axle load, front2)1,764 lbs. (800 kg) 1,764 lbs. (800 kg) 1,786 lbs. (810 kg) 1,786 lbs. (810 kg)
Maximum axle load, rear2)2,690 lbs. (1,220 kg) 2,690 lbs. (1,220 kg) 2,778 lbs. (1,260 kg) 2,778 lbs. (1,260 kg)
Maximum Gross vehicle weight2)4,387 lbs. (1,990 kg) 4,387 lbs. (1,990 kg) 4,508 lbs. (2,045 kg) 4,508 lbs. (2,045 kg)
Maximum roof load3)165 lbs. (75 kg) 165 lbs. (75 kg)––
911 Turbo Coupé 911 Turbo S Coupé 911 Turbo Cabriolet 911 Turbo S Cabriolet
Length 177.4 in. (4,506 mm) 177.4 in. (4,506 mm) 177.4 in. (4,506 mm) 177.4 in. (4,506 mm)
Width without exterior mirrors 74.02 in. (1,880 mm) 74.02 in. (1,880 mm) 74.02 in. (1,880 mm) 74.02 in. (1,880 mm)
Width with exterior mirrors 77.87 in. (1,978 mm) 77.87 in. (1,978 mm) 77.87 in. (1,978 mm) 77.87 in. (1,978 mm)
Height at DIN curb weight 51.02 in. (1,296 mm) 51.02 in. (1,296 mm) 50,87 in. (1,292 mm) 50,87 in. (1,292 mm)
Wheelbase 96.46 in. (2,450 mm) 96.46 in. (2,450 mm) 96.46 in. (2,450 mm) 96.46 in. (2,450 mm)
Ground clearance at maximum gross weight4.17 in. (106 mm) 4.09 in. (104 mm) 4.17 in. (106 mm) 4.09 in. (104 mm)
Turning circle 34.8 ft. (10.6 m) 34.8 ft. (10.6 m) 34.8 ft. (10.6 m) 34.8 ft. (10.6 m)
Reifendruck_TechnischeDaten.fm Seite 288 Mittwoch, 9. April 2014 3:12 15