bulb Ram ProMaster 2014 User Guide

▫Appearance Care And Protection From
Corrosion .......................... .348
▫
Cleaning The Instrument Panel Cupholders . . . .355
 FUSES ............................. .355
▫ Underhood Fuses ..................... .356
▫ Interior Fuses ....................... .361
▫ Right Central Pillar Fuses ................364
 VEHICLE STORAGE ....................365
 REPLACEMENT BULBS .................365
 BULB REPLACEMENT ..................366
▫ Headlamps Low beam and High beam ......366
▫ Front Turn Signal/Parking Lamps .........367▫
Daytime Running Lamp (DRL)/Front Side
Marker Lamp ....................... .368
▫ Front Fog Lamps ..................... .369
▫ Front, Rear Roof Lamps .................369
▫ Rear Tail, Stop, Backup, Turn Signal And
Rear Side Marker Lamps ................370
 FLUID CAPACITIES ....................370
 FLUIDS, LUBRICANTS AND GENUINE
PARTS ............................. .371
▫ Engine ............................ .371
▫ Chassis ........................... .373
320 MAINTAINING YOUR VEHICLE

Your vehicle has a simple ignition actuated test, which
you can use prior to going to the test station. To check if
your vehicle’s OBD II system is ready, you must do the
following:
1. Cycle the ignition switch to the ON position, but donot crank or start the engine.
NOTE: If you crank or start the engine, you will have to
start this test over.
2. As soon as you cycle the ignition switch to the ON position, you will see the MIL symbol come on as part
of a normal bulb check.
3. Approximately 15 seconds later, one of two things will happen:
• The MIL will flash for about 10 seconds and then
return to being fully illuminated until you turn OFF
the ignition or start the engine. This means that your
vehicle’s OBD II system is not readyand you should
not proceed to the I/M station. •
The MIL will not flash at all and will remain fully
illuminated until you turn OFF the ignition or start the
engine. This means that your vehicle’s OBD II system
is ready and you can proceed to the I/M station.
If your OBD II system is not ready,you should see your
authorized dealer or repair facility. If your vehicle was
recently serviced or had a battery failure or replacement,
you may need to do nothing more than drive your
vehicle as you normally would in order for your OBD II
system to update. A recheck with the above test routine
may then indicate that the system is now ready.
Regardless of whether your vehicle’s OBD II system is
ready or not, if the MIL is illuminated during normal
vehicle operation you should have your vehicle serviced
before going to the I/M station. The I/M station can fail
your vehicle because the MIL is on with the engine
running.
324 MAINTAINING YOUR VEHICLE

Cavity Mini Fuse DescriptionF84 20 Amp YellowRear Right Windows
Heater
F85 10 Amp RedRear Heater Prep
VEHICLE STORAGE
If you are leaving your vehicle dormant for more than 21
days, you may want to take these steps to protect your
battery.
•
Disconnect the negative cable from the battery.
• Anytime you store your vehicle, or keep it out of
service (e.g., vacation) for two weeks or more, run the
air conditioning system at idle for about five minutes
in the fresh air and high blower setting. This will
ensure adequate system lubrication to minimize the
possibility of compressor damage when the system is
started again.
REPLACEMENT BULBS
Interior Bulbs
Bulb Number
Overhead Lamp C5W
Sun Visors C5W
Courtesy Lamp FF500
Glove Compartment C5W
Rear Courtesy Lamp C5W
Exterior Bulbs
Bulb Number
Front Low and High Beam
Headlamp H7LL
Front Park/Turn Signal Lamps 7444NA
Daytime Running Lamps
(if equipped) 74407
MAINTAINING YOUR VEHICLE 365

Bulb Number
Front Side Marker Lamps WY5W
Rear Tail/Stop Lamps 7443
Rear Turn Signal Lamps 7440NA
Rear Backup Lamps 921
Rear Side Marker Lamps W3W
Front Fog Lamps H11
License Plate Lamps C5W
Front Roof Lamps WY5W
Rear Roof Lamps W3W
NOTE:
•Numbers refer to commercial bulb types that can
be purchased from your authorized dealer.
•If a bulb needs to be replaced, visit your autho-
rized dealer.
BULB REPLACEMENT
NOTE: Lens fogging can occur under certain atmo-
spheric conditions. This will usually clear as atmospheric
conditions change to allow the condensation to change
back into a vapor. Turning the lamps on will usually
accelerate the clearing process.
Headlamps Low beam and High beam
NOTE: Passenger side headlamp must be removed for
bulb replacement, for driver side headlamp go to step 6
through step 12.
1. Remove screw (1) on lower headlamp filler panel.
2. Remove screws (2) on upper headlamp filler panel.
3. Remove upper screw (1) from headlamp housing.
4. Remove lower screws (2) from headlamp housing.
366 MAINTAINING YOUR VEHICLE

5. Pull Headlamp forward.
6. Remove appropriate plastic cap from the back of theheadlamp housing.
7. Push down on the upper portion of the socket.
8. Pull the socket outward from reflector.
9. Pull bulb outward from socket.
10. Install new bulb.
11. Push socket back into reflector until it locks back into place.
12. Install access cap.
13. Carefully re install headlamp in the same position on the vehicle, so as not to affect headlamp aiming.
14. Install upper screw (1) on headlamp housing. 15. Install lower screws (2) on headlamp housing.
16. Carefully re install screw (1) on lower headlamp filler
panel.
17. Carefully re install screws (2) on upper headlamp filler panel.
Front Turn Signal/Parking Lamps
NOTE: Passenger side headlamp must be removed for
bulb replacement, for driver side headlamp go to step 6
through step 7.
1. Remove screw (1) on lower headlamp filler panel.
2. Remove screws (2) on upper headlamp filler panel.
3. Remove upper screw (1) from headlamp housing.
7
MAINTAINING YOUR VEHICLE 367

4. Remove lower screws (2) from headlamp housing.
5. Pull Headlamp forward.
6. Rotate the bulb counter clockwise and remove.
7. Install the bulb into socket, and rotate bulb/socketclockwise into lamp locking it in place.
8. Carefully re install headlamp in the same position on the vehicle, so as not to affect headlamp aiming.
9. Install upper screw (1) on headlamp housing.
10. Install lower screws (2) on headlamp housing.
11. Carefully re install screw (1) on lower headlamp filler panel.
12. Carefully re install screws (2) on upper headlamp filler panel.Daytime Running Lamp (DRL)/Front Side Marker
Lamp
NOTE: Passenger side headlamp must be removed for
bulb replacement, for driver side headlamp go to step 6
through step 8.
1. Remove screw (1) on lower headlamp filler panel.
2. Remove screws (2) on upper headlamp filler panel.
3. Remove upper screw (1) from headlamp housing.
4. Remove lower screws (2) from headlamp housing.
5. Pull Headlamp forward.
6. Remove the DRL, side marker bulb by pulling straight out.
7. Replace lamp as required and lock in place.
8. Reinstall plastic cap.
368 MAINTAINING YOUR VEHICLE

9. Carefully re install headlamp in the same position onthe vehicle, so as not to affect headlamp aiming.
10. Install upper screw (1) on headlamp housing.
11. Install lower screws (2) on headlamp housing.
12. Carefully re install screw (1) on lower headlamp filler panel.
13. Carefully re install screws (2) on upper headlamp filler panel.
Front Fog Lamps
1. Turn front wheels inboard to access cover in wheelliner.
2. Open the cover on the front of the wheel liner.
3. Remove connection and replace the bulb. 4. Connect the wire and rotate bulb/socket clockwise
into lamp locking it in place.
5. Reinstall the plastic cap and close the cover on the wheel liner.
Front, Rear Roof Lamps
1. Remove two screw and remove the lamp assembly.
2. Remove the socket bulb by turning counterclockwise.
3. Remove bulb and replace as needed.
4. Reinstall the bulb socket and rotate clockwise to lockin place.
5. Reinstall lamp.
7
MAINTAINING YOUR VEHICLE 369

Rear Tail, Stop, Backup, Turn Signal And Rear
Side Marker Lamps
1. Open rear doors.
2. Remove the two screws and remove the tail lamp.
3.
Remove the tail/stop, turn signal, backup and rear side
marker bulb/socket by rotating counter-clockwise.
4. Remove the bulb and replace as needed.
5. Reinstall bulb/socket and rotate clockwise to lock inplace.
6. Reinstall lamp.
FLUID CAPACITIES
U.S. Metric
Fuel (Approximate) 24 Gallons90 Liters
Engine Oil with Filter
3.6L Engine (SAE 5W-20, API Certified) 6 Quarts5.6 Liters
Cooling System *
3.6L Engine (MOPAR® Antifreeze/Engine Coolant
10 Year/150,000 Mile Formula or equivalent) 10.5 Quarts
10 Liters
370 MAINTAINING YOUR VEHICLE

Special Additives...................... .347
Battery ................................ .332
Keyless Transmitter Replacement (RKE) ........20
Belts, Seat ...............................28
Body Builders Guide ........................6
Body Mechanism Lubrication .................336
B-Pillar Location ......................... .231
Brake Assist System ...................... .218
Brake Control System, Electronic ..............216
Brake Fluid ............................ .373
Brake, Parking .......................... .212
Brake System ........................... .214
Anti-Lock (ABS) ....................... .215
Fluid Check .......................... .345
Parking ............................. .212
Warning Light ........................ .132
Brake/Transmission Interlock .................198
Bulb Replacement ........................ .365Bulbs, Light
..............................67
Camera, Rear ............................112
Capacities, Fluid ......................... .370
Caps, Filler Fuel ................................ .260
Power Steering .........................211
Radiator (Coolant Pressure) ................342
Carbon Monoxide Warning ...................64
Car Washes ............................ .349
Cellular Phone .......................... .186
Certification Label ........................ .262
Chains, Tire ............................ .247
Chart, Tire Sizing ........................ .226
Check Engine Light (Malfunction Indicator Light) . .133
Checking Your Vehicle For Safety ...............63
Checks, Safety ............................63
Child Restraint ............................52
Cigar Lighter ............................118
10
INDEX 393

Leaks, Fluid..............................68
Life of Tires ............................ .244
Light Bulbs ..............................67
Lights ..................................67
Airbag ................................45
Anti-Lock ............................ .141
Brake Assist Warning ....................221
Brake Warning ........................ .132
Bulb Replacement ...................... .366
Check Engine (Malfunction Indicator) .........133
Cruise .............................. .131
Daytime Running ........................92
Dimmer Switch, Headlight .................90
Electronic Stability Program (ESP) Indicator .....221
Engine Temperature Warning ...............136
Exterior ...............................67
Fog ................................ .128
Hazard Warning Flasher ..................283
Headlights .............................91 High Beam
............................93
High Beam Indicator .....................128
Illuminated Entry ........................18
Instrument Cluster ..................... .128
Lights On Reminder ......................92
Low Fuel ............................ .137
Map Reading ...........................95
Oil Pressure .......................... .131
Park .................................93
Passing ...............................94
Seat Belt Reminder ..................... .140
Service .............................. .366
Tire Pressure Monitoring (TPMS) ............138
Traction Control ....................... .221
Turn Signal ............................67
Wait to Start .......................... .130
Warning (Instrument Cluster Description) ......128
Loading Vehicle ......................... .262
Capacities ........................... .264
10
INDEX 399