belt RENAULT KANGOO 1997 KC / 1.G Chassis Workshop Manual

85920R2
WHEELS AND TYRES
Specifications
Examples of identification marking
165/70SR1383
125463
165/70 R 13 83 S
TYRES
35
1165
702
3S
R
513
4
Tyre width in mm ( l ) section
Ratio h/lheight
width
Speed index 180 km/h maximum
Radial structure
Inner diameter expressed in inches. Corresponds to the diameter of the rim.
836Load index
Some speed symbols :Maximum speed km/h
R 170
S 180
T 190
U 200
H 210
V 240
ZR over 240
Types of structure :
Diagonal No marking
Radial R
Bias belted B
35-2

STEERING ASSEMBLY
Manual steering assistance pump
36
SPECIAL TOOLING REQUIRED
Dir. 1083Tool for refitting the PAS pump
pulley
B.Vi. 22-01
+Tool for removing the PAS pump
pulley
B.Vi. 47
12996R
REPLACING THE PULLEY (D7F-F8Q engine without
AC)
REMOVAL
Remove:
- the PAS pump belt.
- the pulley (three bolts).
REFITTING
Refitting is the reverse of removal. Observe the
procedure for tensioning the belt (see section 07).
REPLACING THE PULLEY ( E7J engine without AC)
REMOVAL
With the pump removed (see removal method on
following pages), set it in a vice and extract the
pulley using tools B.Vi. 22-01 + B.Vi. 47.
12995R
REFITTING
Refit the pulley using tool Dir. 1083.
Press the pulley on to dimension:
X =34.7 ± 0.2
36-8

STEERING ASSEMBLY
Manual steering assistance pump
36
SPECIAL TOOLING REQUIRED
Mot. 453-01Hose clamp pliers
T. Ar. 1094Extractor
Put the vehicle on a two post lift.
REMOVAL
Remove:
- the PAS pump belt,
- the pulley.
Fit a clamp Mot. 453-01 to the supply pipe.
Disconnect the supply and high pressure pipes.
Take precautions to catch the PAS fluid (protect
the alternator).
Remove the three pump mounting bolts and
remove the pump.
REFITTING
Refitting is the reverse of removal. Observe the
procedure for tensioning the belt (see section 07).
Fill and bleed the circuit, moving the steering
from lock to lock.
D7F engine
without AC
36-9

STEERING ASSEMBLY
Manual steering assistance pump
36
SPECIAL TOOLING REQUIRED
Mot. 453-01Hose clamp pliers
Put the vehicle on a two post lift.
REMOVAL
Remove:
- the right hand wheel,
- the right hand mudguard,
- the bumper (10 bolts).
- the accessories belt,
- the pulley.
Fit a clamp Mot. 453-01 to the supply pipe.
Disconnect the supply and high pressure pipes.
Take precautions to catch the PAS fluid.
Remove the three pump mounting bolts and
remove the pump.
REFITTING
Refitting is the reverse of removal. Observe the
procedure for tensioning the belt (see section 07).
Fill and bleed the circuit, moving the steering
from lock to lock.
F8Q engine
without AC
36-10

STEERING ASSEMBLY
Manual steering assistance pump
36
SPECIAL TOOLING REQUIRED
Mot. 453-01Hose clamp pliers
Put the vehicle on a two post lift.
REMOVAL
Remove:
- the alternator belt,
- the PAS pump belt,
- the alternator.
Fit a clamp Mot. 453-01 to the supply pipe.
Disconnect the supply and high pressure pipes.
Take precautions to catch the PAS fluid.
Remove the three pump mounting bolts and
remove the pump.
REFITTING
Refitting is the reverse of removal. Observe the
procedure for tensioning the belt (see section 07).
Fill and bleed the circuit, moving the steering
from lock to lock.
13296R
E7J engine
without AC
36-11