fuse box diagram RENAULT KANGOO 2013 X61 / 2.G Lighting User Guide

80D-23
AFTER REPAIRCarry out a road test and then a check using the diagnostic tool.
V1 MR-376-X76-80D000$100.mif
LIGHTING
Fault finding – Interpretation of commands80D
UCH
Vdiag No.: 0F
AC023RIGHT-HAND DIRECTION INDICATOR
NOTESThis command is used to activate the right-hand direction indicators.
There must be no present or stored faults.
Check the conformity of the right-hand direction indicator bulbs.
Switch on the ignition.
Special Note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Check for the presence and condition of supply fuse F31 (10 A) on the passenger compartment fuse and relay box,
component code 260 (see MR 374 Mechanical, 81C, Fuses, Fuses: List and location of components).
Check the connection and condition of the indicator control stalk connector, component code 209, and the UCH
connector, component code 645.
If the connector(s) are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the operation of the indicator control stalk in the right-hand indicator position:
Check the continuity between connections 64S and NA of component 209.
Check the continuity of connection NA of component 209.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
UCH_V0F_AC023

80D-27
AFTER REPAIRCheck the system operation.
V1 MR-376-X76-80D000$120.mif
80D
UCH
Vdiag No.: 0F
ALP 2 The direction indicator lights do not work
NOTESOnly consult this customer complaint after a complete check with the diagnostic
tool.
Check the bulbs.
Special Note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Check for the presence and condition of fuse F31 (10 A) on the passenger compartment fuse and relay box,
component code 260 (see MR 374 Mechanical, 81C, Fuses, Fuses: List and location of components).
Press the hazard warning lights switch and check that status ET485 Hazard warning lights signal is PRESENT;
if not, refer to the interpretation of this status.
Activate the right-hand or left-hand indicator and check that ET486 Right-hand indicator signal and ET487 Left-
hand indicator signal are PRESENT. If not, refer to the interpretation of these statuses.
Check the condition of the UCH connector, component code 645.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity of the following connections:
•64C between components 645 and 256, then 173, then 268,
•64D between components 645 and 255, then 172, then 267.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair) repair the wiring, otherwise replace it.
If the fault is still present, contact the techline.
UCH_V0F_ALP02
LIGHTING
Fault finding – Fault Finding Chart

80D-28
AFTER REPAIRCheck the system operation.
V1 MR-376-X76-80D000$120.mif
LIGHTING
Fault finding – Fault Finding Chart80D
UCH
Vdiag No.: 0F
ALP 3 Side lights do not operate
NOTESOnly consult this customer complaint after a complete check with the diagnostic
tool.
Check the bulbs.
Special note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Activate the side lights control and check that status ET484 Side lights signal is PRESENT; if not, refer to the
interpretation of this status.
Check for the presence and condition of fuses F31 and F32 (10 A) on the passenger compartment fuse and relay
box, component code 260 (see MR 374, Mechanical, 81C, Fuses, Fuses: List and location of components).
Check the continuity of the following connections:
•LPG between components 185 and 260,
•LPG between components 173 and 260,
•LPG between components 167 and 260,
•LPD between components 184 and 260,
•LPD between components 172 and 260,
•LPG between components166 and 260.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair) repair the wiring, otherwise replace it.
Check for earths on the following connections:
•MQ of component 184,
•MB of component 185,
•MG of component 173,
•MF of component 172,
•MG of components 166 and 167.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair) repair the wiring, otherwise replace it.
If the fault is still present, contact the techline.
UCH_V0F_ALP03