air condition RENAULT KANGOO 2013 X61 / 2.G Petrol V42 Injection Workshop Manual

17B-170V2 MR-376-X76-17B050$110.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
ET321AIR CONDITIONING COMPRESSOR
STATUS DEFINITIONACTIVE: This status indicates that the air conditioning compressor is active.
INACTIVE: This status indicates that the air conditioning compressor is inactive
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
Conformity check: Engine stopped, ignition on or engine running.
ACTIVETo check the operation of the air conditioning, run command AC180 Air
conditioning compressor relay control. In the event of a fault, apply the
interpretation of DF1072 Air conditioning compressor control.
V42_V04_ET321/V42_V05_ET321/V42_V06_ET321/V42_V14_ET321/V42_V16_ET321/V42_V18_ET321

17B-171V2 MR-376-X76-17B050$110.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
ET405CLUTCH PEDAL SWITCH
STATUS DEFINITIONACTIVE: This status indicates that the clutch pedal is depressed.
INACTIVE: This status indicates that the clutch pedal is released.
NOTESSpecial notes:
Apply the checks only if statuses ACTIVE and INACTIVE are inconsistent
with the pedal position.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant temperature >
80°C.
INACTIVECheck the condition and fitting of the clutch pedal position sensor, component
code
675 (see MR 388 (Logan and Sandero), Mechanical, 37A, Mechanical
component controls, Clutch pedal position sensor: Removal - Refitting or MR
451 (Duster) or MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6), Mechanical,
37A, Mechanical component controls, Clutch pedal: Removal - Refitting).
Remove the clutch pedal position sensor, component code 675 (see MR 388
(Logan and Sandero), Mechanical, 37A, Mechanical component controls,
Clutch pedal position sensor: Removal - Refitting or MR 451 (Duster) or MR 423
(Thalia 2/Symbol 2), MR 430 (Clio II F 6), Mechanical, 37A, Mechanical
component controls, Clutch pedal: Removal - Refitting).
Check the insulation between connections MAM (for Logan, Sandero, Duster) or
M (for Thalia 2/Symbol 2, Clio II F 6) and 86D of component 675 with the switch in
the rest position.
– Repeat this operation with the switch pressed, and check the continuity and the
absence of interference resistance between the two connections.
If these 2 checks are not correct, replace the clutch pedal position sensor,
component code 675 (see MR 388 (Logan and Sandero), Mechanical, 37A,
Mechanical component controls, Clutch pedal position sensor: Removal -
Refitting or MR 451 (Duster) or MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6),
Mechanical, 37A, Mechanical component controls, Clutch pedal: Removal -
Refitting).
V42_V04_ET405/V42_V05_ET405/V42_V06_ET405/V42_V14_ET405/V42_V16_ET405/V42_V18_ET405

17B-172V2 MR-376-X76-17B050$110.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
ET405
CONTINUED
INACTIVE
(CONTINUED)
Then check the continuity and absence of interference resistance of the following
connection:
–86D between components 120 and 675.
Check that the earth is correct on connection MAM (for Logan, Sandero, Duster) or
M (for Thalia 2/Symbol 2, Clio II F 6) of component 675.
If the connection(s) are faulty and there is a repair procedure (see Technical Note
6015A, Electrical wiring repair, Wiring: Precautions for repair), repair the
wiring, otherwise replace it.
ACTIVECheck the condition and fitting of the clutch pedal position sensor.
Remove the clutch pedal position sensor, component code 675 (see MR 388 (Logan
and Sandero), Mechanical, 37A, Mechanical component controls, Clutch pedal
position sensor: Removal - Refitting or MR 451 (Duster) or MR 423 (Thalia 2/
Symbol 2), MR 430 (Clio II F 6), Mechanical, 37A, Mechanical component
controls, Clutch pedal: Removal - Refitting) and check the insulation between
connections MAM and 86D of component 675 with the switch in the rest position.
– Repeat this operation with the switch pressed, and check the continuity and the
absence of interference resistance between the two connections.
If these 2 checks are not correct, replace the clutch pedal position sensor, component
code 675 (see MR 388 (Logan and Sandero) or 451 (Duster) and MR 423 (Thalia
2/Symbol 2), Mechanical, 37A, Mechanical component controls, Clutch pedal
position sensor: Removal - Refitting or MR 451 (Duster) or MR 423 (Thalia 2/
Symbol 2), MR 430 (Clio II F 6), Mechanical, 37A, Mechanical component
controls, Clutch pedal: Removal - Refitting).

17B-184
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$130.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
PR030ACCELERATOR PEDAL POSITION
PA R A M E T E R
DEFINITIONThis parameter indicates the accelerator pedal position as a %.
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant temperature >
80°C.
No load  16%
Full load  85%
Check that the pedal mechanism has not seized.
Check the cleanliness and condition of the pedal potentiometer connections, component code 921 and the
injection computer connections, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Disconnect the battery and the injection computer.
Use the "Universal bornier" to check the insulation and continuity of the following connections:
–3LT between components 120 and 921,
–3LR between components 120 and 921,
–3LS between components 120 and 921,
–3LV between components 120 and 921,
–3LU between components 120 and 921,
–3LW between components 120 and 921.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
In the event of a fault, apply the interpretation of DF974 Pedal potentiometer circuit gang 1 and DF975 Pedal
potentiometer circuit gang 2.
V42_V04_PR030/V42_V05_PR030/V42_V06_PR030/V42_V14_PR030/V42_V16_PR030/V42_V18_PR030

17B-185V2 MR-376-X76-17B050$130.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test, then check with the diagnostic tool.
PR037REFRIGERANT PRESSURE
PA R A M E T E R
DEFINITIONThis parameter indicates the refrigerant pressure in bar.
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant temperature >
80°C.
The refrigerant pressure must be between 2 bar < PR037 < 27 bar.
Check the cleanliness and condition of the refrigerant pressure sensor and its connections, component code
1202 and the injection computer connections, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Disconnect the battery and the injection computer.
Using the universal bornier in place of the computer, check for insulation and continuity on the following
connections:
–38Y between components 120 and 1202,
–38X between components 120 and 1202,
–38U between components 120 and 1202.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the refrigerant pressure sensor, component code 1202 (see MR 388 (Logan and
Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL),
Mechanical, 62A, Air conditioning, Pressure sensor: Removal - Refitting).
(See MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), Mechanical, 62A, Air
conditioning: Precautions for repair) and (see MR 388 (Logan and Sandero), MR 451 (Duster) or MR 423
(Thalia 2/Symbol 2), Mechanical, Air conditioning: Parts and consumables for the repair).
If the fault is present, check the air conditioning circuit (see MR 388 (Logan and Sandero), MR 451 (Duster) or
MR 423 (Thalia 2/Symbol 2), Mechanical, 62A, Air conditioning: Check).
V42_V04_PR037/V42_V05_PR037/V42_V06_PR037/V42_V14_PR037/V42_V16_PR037/V42_V18_PR037

17B-213V2 MR-376-X76-17B050$140.mif
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
*TDC: Top Dead Centre
**GMV: fan assemblyTool
commandDiagnostic tool title Comments
RZ001 Fault memoryThis command is used to clear the faults stored in the computer.
RZ003 Engine adaptivesThis command enables a long engine start time.
RZ031 Throttle stop programmingThis command is used to reset the necessary system adaptives
if replacing the throttle valve.
RZ033Richness regulation
programmingThis command is used to reset the necessary system adaptives
if replacing the injectors.
RZ037Flywheel target
programmingThis command is used to reset the necessary system adaptives
if replacing the TDC* sensor.
RZ064Programming the level of
alcoholThis command is used to count the richness adaptive
programming necessary when replacing the injection computer.
AC005 Cylinder 1 injectorThis command is used to perform an audible check on injector 1.
AC006 Cylinder 2 injectorThis command is used to perform an audible check on injector 2.
AC007 Cylinder 3 injectorThis command is used to perform an audible check on injector 3.
AC008 Cylinder 4 injectorThis command is used to perform an audible check on injector 4.
AC015 Fuel pump relayThis command is used to check the fuel pump.
AC017Canister bleed solenoid
valveThis command is used to check the canister bleed solenoid
valve.
AC027 Motorised throttleThis command is used to check the motorised throttle.
AC038 Low speed GMV** relayThis command is used to check the low speed GMV** relay.
AC039 High speed GMV** relayThis command is used to check the high speed GMV** relay.
AC180Air conditioning
compressor relay controlThis command is used to check the air conditioning compressor
relay.
PETROL INJECTION
Fault finding – Command summary table

17B-220
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$160.mif
PETROL INJECTION
Fault finding – Fault Finding Chart17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
ALP 1 No dialogue with the computer
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Try to establish dialogue with a computer on another vehicle to make sure that the diagnostic tool is not faulty. If
the tool is not the cause and communication cannot be established with any other computer on the same vehicle,
it is possible that another computer is disrupting the multiplex network.
Check the voltage of the battery.
If the battery voltage is between 9.5 V and 17.5 V, run fault finding on the charging circuit.
– Check the presence and condition of the injection fuses on the UPC and in the engine fuse box.
– Check the connection of the computer connectors, component code 120.
– Check the injection computer earths (quality, oxidation, tightness of the earth bolts on the battery terminal).
– Check that the supply to the computer is correct:
–Earth on connection NH of component 120 (for Logan, Sandero, Duster, Kangoo VLL),
–Earth on connection N of component 120 (for Thalia 2/Symbol 2),
–Earth on connection NF of component 120 (for Clio II F 6)
–+ 12V on connection 3FB of component 120.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check that the diagnostic socket, component code 225 is correctly supplied:
–+ before ignition feed on connection BP56 of component 225 (for Logan, Sandero, Duster),
–+ before ignition feed on connection BP10 of component 225 (for Thalia 2/Symbol 2, Clio II F 6, Kangoo
VLL),
–+ after ignition feed on connection AP10 of component 225,
– Earth on connections MAM and NC of component 225 (for Logan, Sandero, Duster
),
– Earth on connections N and M of component 225 (for Thalia 2/Symbol 2, Clio II F 6),
– Earth on connections NA and MK of component 225 (for Kangoo VLL).
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If dialogue has still not been established after these checks, contact the techline.
V42_V04_ALP1/V42_V05_ALP1/V42_V06_ALP1/V42_V14_ALP1/V42_V16_ALP1/V42_V18_ALP1
PETROL INJECTION
Fault finding – Fault Finding Chart

17B-251
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$180.mif
PETROL INJECTION
Fault finding – Tests17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
TEST 2 Alternator signal module check
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
With the engine running, check the alternator charge without any electrical consumers switched on using PR002
Alternator charge, then switch on the consumers and check the increase in PR002.
Check the cleanliness and condition of the alternator connector, component code 103 and of the injection
computer connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connection.
–2K between components 103 and 120.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the check is correct, replace the alternator signal module, component code 103 (see MR 388 (Logan and
Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL),
Mechanical, 16A, Starting - Charging, Alternator: Removal - Refitting).
If the fault is still present, contact the techline.
V42_V04_TEST2/V42_V05_TEST2/V42_V06_TEST2/V42_V14_TEST2/V42_V16_TEST2/V42_V18_TEST2

17B-253
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$180.mif
PETROL INJECTION
Fault finding – Tests17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
TEST 4 Fuel vapour absorber solenoid valve check
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the cleanliness, mounting, possible leaks and the hoses of the fuel vapour absorber solenoid valve,
component code 371 (see MR 388, Mechanical, 14A, Emission control, Fuel vapour recirculation circuit:
Check or MR 451 (Duster) or MR 423 (Thalia 2/Symbol 2), Mechanical, 14A, Emission control, Fuel vapour
absorber: Removal - Refitting).
Listen for the operation of the solenoid valve while running command AC017 Canister bleed solenoid valve.
With the engine idling, disconnect the pipe at the solenoid valve inlet and check that there is no suction on your
finger. (These steps allow the sealing of the solenoid valve to be checked for air tightness.)
Check the cleanliness and condition of the canister bleed solenoid valve connector, component code 371 and
of the injection computer connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3FB between components 371 and 1047 (for Logan, Sandero, Duster) or 238 (for Thalia 2/Symbol 2, Kangoo
VLL) or 983 (for Clio II F 6),
–3BB between components 371 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
V42_V04_TEST4/V42_V05_TEST4/V42_V06_TEST4/V42_V14_TEST4/V42_V16_TEST4/V42_V18_TEST4

17B-255
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$180.mif
PETROL INJECTION
Fault finding – Tests17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
TEST 5 Additional fuel tank check
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the cleanliness, the mounting and for possible leaks of the hoses of the solenoid valve (see MR 388 (Logan
and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL),
Mechanical, 19C, Tank, Fuel pump of the additional fuel tank: Removal - Refitting).
Listen to the operation of the solenoid valve by running command AC217 Additional petrol circuit solenoid
valve.
Check the cleanliness and condition of the connector of the additional petrol circuit solenoid valve, component
code 1640 and the connector of the injection computer, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
V42_V04_TEST5/V42_V05_TEST5/V42_V06_TEST5/V42_V14_TEST5/V42_V16_TEST5/V42_V18_TEST5