air condition RENAULT KANGOO 2013 X61 / 2.G Petrol V42 Injection Workshop Manual

17B-258
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$180.mif
PETROL INJECTION
Fault finding – Tests17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
TEST 7 Air inlet pressure sensor check
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the fitting and sealing of the inlet air pressure sensor, component code 147 (condition of the seals) and look
for possible leaks on the inlet air pipe. Ensure the conformity of the system (see MR 388 (Logan and Sandero),
MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 12A,
Fuel mixture, Air inlet: Description).
With the ignition on, compare the value of PR312 Manifold pressure for the vehicle concerned with that given by
another vehicle (absolute difference < 130 mbars).
Check the connection and condition of the connector of the inlet air pressure sensor, component code 147 and
of the injection computer connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the supply voltage of the sensor on connections 3AJR and 3AJP.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3AJP between components 120 and 147,
–3AJR between components 120 and 147,
–3AJQ between components 120 and 147.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the ignition on, use a vacuum pump in order to create a variation in negative pressure. Then use the
diagnostic tool to check that PR312  500 mbar.
Replace the inlet air pressure sensor, component code 147 (see MR 388 (Logan and Sandero), MR 451 (Duster),
MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 12A, Fuel mixture,
Air inlet: Description) and repeat the vacuum test.
If the fault is still present, contact the Techline.
V42_V04_TEST7/V42_V05_TEST7/V42_V06_TEST7/V42_V14_TEST7/V42_V16_TEST7/V42_V18_TEST7

17B-262
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$180.mif
PETROL INJECTION
Fault finding – Tests17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
TEST 9 Brake pedal switch check
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
With the brake pedal released, check ET039 Brake pedal and ET799 Brake wire contact.
ET039 must be 01 and ET799 must be 01.
While depressing the brake pedal, check ET039 and ET799.
ET039 must be 02 and ET799 must be 02.
If these two checks are correct, the switch is not faulty.
Check the fitting and mechanical operation of the brake pedal (the pedal returns properly).
If the check is incorrect, check the braking system.
With the brake pedal depressed, measure the resistance of the brake pedal switch, component code 160
between connections AP1 (for Logan, Sandero, Duster) or AP10 (for Thalia 2/Symbol 2, Clio II F 6, Kangoo
VLL) and 65A. The value must be X > 10 M (between 0°C and 40°C).
If the resistance is not correct, replace the brake pedal switch, component code 160 (see MR 388 (Logan and
Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL),
Mechanical, 37A, Mechanical component controls, Brake pedal switch: Removal - Refitting).
With the brake pedal released, measure the resistance of the brake pedal switch, component code 160 between
connections AP1 (for Logan, Sandero, Duster) or AP10 (for Thalia 2/Symbol 2, Clio II F 6, Kangoo VLL) and
5A. The value must be between 0  < X < 1 (between
0°C and 40°C).
If the resistance is not correct, replace the brake pedal switch, component code 160 (see MR 388 (Logan and
Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL),
Mechanical, 37A, Mechanical component controls, Brake pedal switch: Removal - Refitting) and move on
to the Section: Checking the brake pedal switch.
Check the condition of the brake pedal switch connector, component code 160 (see MR 388 (Logan and
Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL),
Mechanical, 37A, Mechanical component controls, Brake pedal switch: Removal - Refitting).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
V42_V04_TEST9/V42_V05_TEST9/V42_V06_TEST9/V42_V14_TEST9/V42_V16_TEST9/V42_V18_TEST9

17B-263
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$180.mif
PETROL INJECTION
Fault finding – Tests17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
TEST 9
CONTINUED
Check the presence and condition of brake pedal fuse F03 (for Logan, Sandero, Duster), F4 (for Thalia 2/Symbol
2, Clio II F 6) or F16 (for Kangoo VLL).
Check the insulation, continuity and the absence of interference resistance on the following connections:
–AP1 between components 160 and 1016 (for Logan, Sandero, Duster),
–AP10 between components 160 and 1016 (for Thalia 2/Symbol 2, Clio II F 6)
–AP10 between components 160 and 260 (for Kangoo VLL),
–5A between components 160 and 120,
–65A between components 160 and120,
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.

17B-264
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$180.mif
PETROL INJECTION
Fault finding – Tests17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
TEST 10 TDC sensor check
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the sensor fitting (connectors, mountings, etc.) (see MR 388 (Logan and Sandero), MR 451 (Duster), MR
423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 17B, Petrol Injection,
Crankshaft position sensor: Removal - Refitting).
Switch on the ignition, check the change of the engine rotation speed using parameter PR055 Engine speed. The
value must be between 0 rpm and more than 120 rpm when the starter is operating.
With the engine running, accelerate to obtain different engine rotation speeds and check that the engine speed
correctly changes in relation to the accelerations.
If PR055 varies, the sensor is sound.
Check the cleanliness and condition of the TDC sensor, component code 149 and of the injection computer
connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
V42_V04_TEST10/V42_V05_TEST10/V42_V06_TEST10/V42_V14_TEST10/V42_V16_TEST10/V42_V18_TEST10

17B-266
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$180.mif
PETROL INJECTION
Fault finding – Tests17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
TEST 11 Pinking sensor check
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Start the engine and let it idle. Next, check that PR427 Average pinking signal is equal to 0.
With the engine idling, check that parameters PR469 Cylinder 1 pinking value, PR471 Cylinder 2 pinking value,
PR473 Cylinder 3 pinking value, PR475 Cylinder 4 pinking value are all 0.
Check the cleanliness and condition of the pinking sensor connector, component code 146 and of the injection
computer connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the resistance of the pinking sensor, component code 146 between connections 3DQ and 3S on the
injection computer connector side, component code 120 (see MR 388 (Logan and Sandero). MR 451 (Duster),
MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 17B, Petrol injection,
Petrol injection computer: Removal - Refitting).
The resistance must be greater than 10 M or between 559 k < X < 561 k (F4R engine of Duster).
If the resistance value is not correct, replace the pinking sensor, component code 146 (see MR 388 (Logan and
Sandero). MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL),
Mechanical, 17B, Petrol injection, Petrol injection: List and location of components).
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3DQ between components 120 and 146,
–3S between components 120 and 146.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
V42_V04_TEST11/V42_V05_TEST11/V42_V06_TEST11/V42_V14_TEST11/V42_V16_TEST11/V42_V18_TEST11

17B-268
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$180.mif
PETROL INJECTION
Fault finding – Tests17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
TEST 13 Injector check
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Perform a visual inspection of the condition and possible leaks in the system.
Repair if necessary (see MR 388 (Logan and Sandero), Mechanical, 13A, Fuel supply, Injector rail - Injectors:
Removal - Refitting, MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo
VLL), Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal - Refitting).
Listen to the operation of the injectors by running the commands:
–AC005 Cylinder 1 injector,
–AC006 Cylinder 2 injector,
–AC007 Cylinder 3 injector,
–AC008 Cylinder 4 injector.
Replace the injectors if necessary (see MR 388 (Logan and Sandero), Mechanical, 13A, Fuel supply, Injector
rail - Injectors: Removal - Refitting, MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR
374 (Kangoo VLL), Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal - Refitting).
If the fault is still present, contact the techline.
V42_V04_TEST13/V42_V05_TEST13/V42_V06_TEST13/V42_V14_TEST13/V42_V16_TEST13/V42_V18_TEST13

17B-269
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$180.mif
PETROL INJECTION
Fault finding – Tests17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
TEST 14 Ignition coil check
NOTESSpecial note:
To apply this procedure, use the special tool Elé. 1808: "ignition coil tester"
available in the Parts Department catalogue.
part number: 77 11 381 808.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
K4M engine
Visually inspect the condition of the connectors of pencil ignition coil no.1, component code 1077, pencil ignition
coil no.2, component code 1078, pencil ignition coil no.3, component code 1079, and pencil ignition coil no.4,
component code 1080 (see MR 388 (Logan et Sandero). MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR
430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 17A, Ignition, Coils: Removal - Refitting).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Insert tool Elé. 1808 (1) in the coil.
Place the tool/coil assembly in the spark plug well.
Start the engine and let it idle.
Apply light pressure to the assembly to hold the coil in contact with the tool.
Observe the glow from the electric arc on the spark plug well wall.
If an electric arc is not produced, replace the coil concerned (see MR 388 (Logan and Sandero). MR 451 (Duster),
MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 17A, Ignition, Coils:
Removal - Refitting).
If the fault is still present, contact the techline.
V42_V04_TEST14/V42_V05_TEST14/V42_V06_TEST14/V42_V14_TEST14/V42_V16_TEST14/V42_V18_TEST14

17B-270
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$180.mif
PETROL INJECTION
Fault finding – Tests17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
*BVM: Manual gearbox.
*BVA: Automatic gearbox.
TEST 14
CONTINUEDIgnition coil check
K7M engine
Visually inspect the condition of the connectors of the ignition coil, component code 778 (see MR 388 Mechanical,
17A, Ignition, Coils: Removal - Refitting).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Insert tool Elé. 1808 (1) in the cap of the wire of the plug concerned.
Fit the assembly in the plug well.
Start the engine and let it idle.
Apply light pressure to the assembly to hold the coil in contact with the tool.
Observe the glow from the electric arc on the spark plug well wall.
If the electric arc is not produced, replace the ignition coil (see MR 388 Mechanical, 17A, Ignition, Coils:
Removal – Refitting).
If the fault is still present, contact the techline.
D4D engine
– Switch on the vehicle + after ignition feed.
– Run command VP036 FUEL SUPPLY INHIBITION.
Put the vehicle under starting conditions:
– position of gear lever in neutral for a manual gearbox* or position "P" (Parking) for an automatic gearbox*.
– brake pedal depressed.
– Run command RZ003 ENGINE ADAPTIVES.
Remove the plugs from each cylinder and check, one after another, that sparks are present by bringing the plug
close to a chassis earth, with the starter engaged. If no spark is produced, replace the ignition coil, component
code 778 (see MR 388 Mechanical, 17A, Ignition, Coils: Removal – Refitting).
If the fault is still present, contact the techline.

17B-271
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$180.mif
PETROL INJECTION
Fault finding – Tests17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
TEST 15 Coolant temperature sensor check
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
With the engine idling: visually check that there are no leaks from the fitting of the coolant temperature sensor,
component code 244 (see MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR
430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 19A, Cooling, Coolant temperature sensor: Removal
- Refitting).
Switch off the engine. Wait for 15 minutes, restart the engine and, for 10 minutes, check that the temperature
value given by the sensor increases, using parameter PR064 Coolant temperature.
If the value increases, the sensor is sound.
Check the condition of the coolant temperature sensor connector, component code 244 and the injection
computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the supply between connections 3JK and 3C of component 244.
Check the insulation, continuity and absence of interference resistance on the following connections:
–3JK between components 244 and 120,
–3C between components 244 and 120.
If the connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the fault is still present, replace the coolant temperature sensor, component code 244 (see MR 388 (Logan
and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL),
Mechanical, 19A, Cooling, Coolant temperature sensor: Removal - Refitting).
If the fault is still present, contact the techline.
V42_V04_TEST15/V42_V05_TEST15/V42_V06_TEST15/V42_V14_TEST15/V42_V16_TEST15/V42_V18_TEST15

17B-272
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$180.mif
PETROL INJECTION
Fault finding – Tests17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
TEST 16 Fan relay check
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the operation of the low speed fan assembly by running command AC038 Low speed fan assembly relay.
Check the operation of the high speed fan assembly by running command AC039 High speed fan assembly
relay.
If these two checks are correct, the fan assembly relay is not faulty
Run command AC038 and use the test light to check for the control signal of component 120 on connection 3JN
of component 700 (for Logan, Sandero, Duster) or 784 (for Thalia 2/Symbol 2, Clio II F 6, Kangoo VLL).
Check the connection and condition of the fan assembly connector, component code 188 (for Logan, Sandero,
Duster) or 262 (for Thalia 2/Symbol 2, Clio II F 6, Kangoo VLL) and the injection computer connector,
component code 120.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connections:
For Logan, Sandero, Duster:
–3JN between components 700 and 120,
–49C between components 321 and 700,
–49B between components 188 and 321.
For Thalia 2/Symbol 2, Clio II F 6, Kangoo VLL:
–3JN between components 784 and 120,
–49C between components 784 and 321,
–49C between components 262 and 321.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
V42_V04_TEST16/V42_V05_TEST16/V42_V06_TEST16/V42_V14_TEST16/V42_V16_TEST16/V42_V18_TEST16