RENAULT MEGANE SCENIC 1995 Service Repair Manual

GLAZING
Front door window
Fit the window flush with the fixed window pillar
seal (C).
The height of the window is adjusted by moving
the stop (7) of the window mechanism toothed
wheel.
54
Tighten the upper pillar bolt (6).
Open the door and tighten the lower pillar
mounting (6).
Position the fixed window fully in the pillar
groove.
Fit the window flush with the pillar seal (A) and
with a protrusion (B = 1 mm) with the exterior
mirror seal.Tighten the mounting bolts (5).
Tightening torque of all mounting bolts 8 N.m.
MM M M
OO O O
VV V V
AA A A
BB B B
LL L L
EE E E

WW W W
II I I
NN N N
DD D D
OO O O
WW W W
12281-1R1
12281-1R2
12277-2R
12469R
54-3

GLAZING
Front door window
Place the rear upper stop (8) in contact with the
lower window pad and tighten it.
Tighten the rear guide shoe bolt (2).
Tighten the window mounting bolts (3).
54
Place the front upper stop (8) in contact with the
lower window pad and tighten it.
Close and lock the hood.
Close the door.
Position the window at the dimensions:
D = 55 mm (window/weatherstrip)
E = 10 mm (window/frame)
Visually check that the window is aligned with the
hood seals.
12470R
12277-3R
12277-3R1
Tighten the rear slider bolt (4).
Open the door.
Push the rear slider gently towards the exterior of
the door.
Tighten the nut (4).
Open and close the window several times. Check
that the window is positioned correctly (aligned)
in relation to the hood seals.
Tightening torque of all mounting bolts 8 N.m.
54-4

GLAZING
Quarter light
Open the window by approximately 10 cm.
Remove the window.
AA A A
DD D D
JJ J J
UU U U
SS S S
TT T T
MM M M
EE E E
NN N N
TT T T
The hood must be open, the movable door
window must be closed and correctly adjusted
with the window weatherstrip in place.
54
RR R R
EE E E
MM M M
OO O O
VV V V
AA A A
LL L L
After removing the seat, rear bench seat backrest,
interior trim, remove:
- the weatherstrip and the sealing felt,
Position the quarter light at a distance of A = 20
mm between the door window and the seal
retaining rail.
PRE5402
12439R
12295-2R
- the mounting nuts (1).
54-5

GLAZING
Quarter light
54
Make flush the line: quarter light/movable door
window (adjustment is by the stops (2)).
Tighten the window mounting bolts (1).
12295-1R
12439R1
Place the quarter light seal in contact with the
door window at the bottom (B).
Tighten the upper mounting bolts (3).
12295R1
Open the door to the 1st notch, place the quarter
light seal in contact with the door window at the
top (C).
Tighten the lower mounting bolts (4).
Tightening torque of all mounting bolts 8 N.m.
54-6

EXTERIOR ACCESSORIES
Exterior mirror
56
Remove:
- the bolt (1), the cover and the blanking piece.
- the mounting nuts (2).
12288R
12287R
56-1

UPPER INTERIOR ACCESSORIES
Road box
Fit:
- the clamps to the cover (C),
- the compartment cover to the frame (B) and
secure it using bolts (HEX M5×12).
Degrease the foam strip (D) positioning grooves
(heptane surface cleaner).
Glue the strips.
58
PRE5801
AA A A
SS S S
SS S S
EE E E
MM M M
BB B B
LL L L
YY Y Y
Position the side panels (A) on the frame (B) and
secure them using bolts (HEX M4×8).
12477R
12478R
58-1

UPPER INTERIOR ACCESSORIES
Road box
Secure it using the milled bolts and the crossed
nuts.
58
12468
With the hood folded and the hood cover open,
remove:
- the mounting nuts,
12467
- the bench seat cushion mounting bolts,
- the cushion.Unclip the seat belts.
Remove the bench seat backrest.
Clip the seat belt.
Fit:
- the carpet
- the road box (2 people).
12476R
58-2

UPPER INTERIOR ACCESSORIES
Road box
CC C C
HH H H
AA A A
NN N N
GG G G
II I I
NN N N
GG G G

TT T T
HH H H
EE E E

BB B B
LL L L
II I I
NN N N
DD D D

LL L L
OO O O
CC C C
KK K K
II I I
NN N N
GG G G

MM M M
OO O O
TT T T
OO O O
RR R R
58
Close the hood cover.
Check the clearance (5 mm) between the
compartment and the hood cover.
If necessary, adjust the clearance using the nut (1).
Connect the electrical wiring (A).After removing the road box, disconnect the
motor harness (1).
Detach the locking rod (2).
Remove the mounting bolt (3).
12479R12475R
58-3

77 11 192 972FF F F
EE E E
BB B B
RR R R
UU U U
AA A A
RR R R
YY Y Y

11 1 1
99 9 9
99 9 9
77 7 7Edition Anglaise
"The repair methods given by the manufacturer in this document are based on the
technical specifications current when it was prepared.
The methods may be modified as a result of changes by the manufacturer in the
production of the various component units and accessories from which his vehicles
are constructed".All copyrights reserved by Renault.
Copying or translating, in part or in full, of this document or use of the service part
reference numbering system is forbidden without the prior written authority of
Renault.
CRenault 1997
Sealing and soundproofing
BODY SEALING

Pages
Contents
Sealing and
soundproofing
WINDOW SEALING64
64-1 Windscreen pillar seal