RENAULT MEGANE SCENIC 1995 Service Repair Manual

FUEL TANK
Pump and sender unit
19
Use pliers Mot. 1265 (petrol engine) or Mot. 1265-
01 (diesel engine) to disconnect:
- the fuel supply pipe (3) (marked by a green
quick release union),
- the fuel return pipe (4) (marked by a red quick
release union and an arrow (B)).
96420R1
Remove the mounting nut (5) using tool
Mot. 1264-01 (release the nut, remove the tool
then slacken the nut by hand and remove it).
Remove the pump and sender unit assembly.
99367S
NOTE : if several hours may elapse between remo-
ving and refitting the pump and sender unit as-
sembly, refit the nut to the fuel tank to prevent it
from distorting.
19-27

FUEL TANK
Pump and sender unit
19
REFITTING
Check the seal is not damaged and renew it if ne-
cessary.
First fit the seal on the fuel tank before refitting
the assembly.
Position the pump and sender unit assembly (ar-
row (F) should be aligned with the longitudinal
axis of the vehicle, pointing backwards).
Fit the nut and tighten it to a torque of
3.5 daN.m.
Clip the fuel pipes back together (tools Mot. 1265
or Mot. 1265-01 do not need to be used).
Refit the safety clips (2).
Reconnect the electrical connector .
Refit the plastic cover.
ALLOCATION OF CONNECTOR TRACKS
TRACK ALLOCATION
A1 Earth
A2 Low fuel warning light
B1 Gauge information to instrument panel
B2 Not used
C1 Pump
C2 Pump
19-28

ENGINE SUSPENSION
Suspended engine mountings
19
ADJUSTING THE LONGITUDINAL MOVEMENT LIMITER FOR F ENGINES
Slacken limiter bolts (E).
Insert the limiter centring fork Mot. 1289-03 into the openings on the suspended engine mounting cover.
Tighten the two bolts (E) to a torque of 5 to 6.5 daN.m.
99174-2R
F engine (petrol)
99166-1R1
F engine (diesel)
F ENGINES
19-29

ENGINE SUSPENSION
Suspended engine mountings
19
TIGHTENING TORQUES (in daN.m)F3R ENGINE
99308R
*Tighten the stud to 6 daN.m
**Tighten the nut to 4 daN.m
19-30

ENGINE SUSPENSION
Suspended engine mountings
19
TIGHTENING TORQUES (in daN.m)F8Q ENGINE
99309R1
*Tighten the stud to 6 daN.m
**Tighten the nut to 4 daN.m
19-31

ENGINE SUSPENSION
Engine mounting pads
19
TIGHTENING TORQUES (in daN.m)
PRG19.1
E7J/K7M ENGINE
19-32

ENGINE SUSPENSION
Engine mounting pads
19
TIGHTENING TORQUES (in daN.m)K7M ENGINE / AT
PRG19.2
19-33

77 11 176 221SEPTEMBER 1995Edition Anglaise
"The repair methods given by the manufacturer in this document are based on the
technical specifications current when it was prepared.
The methods may be modified as a result of changes introduced by the
manufacturer in the production of the various component units and accessories
from which his vehicles are constructed."All copyrights reserved by the Regie Nationale des Usines Renault.
Copying or translating, in part or in full, of this document or use of the service part
reference numbering system is forbidden without the prior written authority of the
Regie Nationale des Usines Renault.
CRégie Nationale des Usines Renault S.A. 1995
Transmission
CLUTCH
MANUAL GEARBOX
BA0A - BA0E - BA0F - BA0G - BA0L - BA0U
AUTOMATIC TRANSMISSION
DRIVESHAFTS

EXPLODED VIEW
PRG20.1

21-1
21-2
21-3
21-4
21-5
21-5
21-6
21-9
21-19
21-23
21-26
Contents
Page
23-1
23-2
23-3
23-3
23-4
23-5
23-5
23-5
23-6
23-6
23-7
23-8
23-8
23-9
23-15
23-20
23-23
23-27
23-29 Section view
Use
Identification
Gear ratios
Gear change thresholds
Consumables
Parts to be systematically replaced
Oil
Oil change frequencies
Fault warning light
Draining
Filling - levels
Oil pressure
Hydraulic distributor
Automatic transmission (Removal -
Refitting)
Differential output seal
Wiring
Wiring diagram
Checking the "timing point" on the
converter AUTOMATIC TRANSMISSION
23
Transmission
CLUTCH
Identification
Section views
Exploded views
Consumables
Fault finding
Mechanism - Plate
Thrust pad - Fork20
20-1
20-3
20-3
20-4
20-5
20-13
20-14
Identification
Ratios
Capacity -Lubricants
Special notes
Consumables
Parts to be systematically replaced
Fault finding
Gearbox (Removal - Refitting)
5th gear on the vehicle
Differential output seal
Speedometer drive gear
MANUAL GEARBOX21
29-1
29-2
29-9
29-10
29-17
29-24 Consumables
Driveshafts
Front transverse driveshafts
Gaiter on wheel end
Gaiter on gearbox end
Bearing gaiter DRIVESHAFTS
29
Page