display RENAULT SCENIC 2006 J84 / 2.G Multimedia Nav 4R Owner's Manual

MULTIMEDIA
Fault finding - Conformity check
86C
86C-32
NAV 4R
Program no.: 0000
Vdiag No.: 24
Sub-function: Display
NOTESOnly perform this conformity check after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine stopped, ignition on.
Order FunctionParameter / Status
checked or ActionDisplay and Notes Fault finding
1Power supplyET003:+ 12 V side
lights feedPRESENT
ABSENTIn the event of a fault, consult
the interpretation of status
ET003 + 12 V side lights
feed.
2OffET004:RADIO ON
signalSTILL PRESENTIn the event of a fault, consult
the interpretation of status
ET004 RADIO ON signal.
3DisplayAC021:Display testThis command is used
to check that the
display is operating
correctly.In the event of a fault, consult
the interpretation of fault
DF031 Computer/display
connection.

MULTIMEDIA
Fault finding - Conformity check
86C
86C-33
NAV 4R
Program no.: 0000
Vdiag No.: 24
Sub-function: Audio
NOTESOnly perform this conformity check after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine stopped, ignition on.
Order FunctionParameter / Status
checked or ActionDisplay and Notes Fault finding
1Radio
reception
qualityPR010:Radio field
intensityUnit: dBµµ µ µ
VIn the event of a fault, consult
the interpretation of
parameter PR010 Radio
field intensity.
2SpeakersAC004:Speaker testThis command is used
to perform a listening
test on each speaker.of command AC004 Speaker
test.

MULTIMEDIA
Fault finding - Interpretation of statuses
86C
86C-38
NAV 4R
Program no.: 0000
Vdiag No.: 24
ET004
RADIO ON SIGNAL
NOTESThere must be no present or stored faults.
Switch on the ignition, status ET004 should be permanently PRESENT.
Apply this fault finding procedure only if the vehicle is equipped with a display fold-out
unit and an instrument panel dot matrix display (Mégane II ph2).
Use the Wiring Diagrams Technical Note for Mégane II phase 2.
Check the condition and connection of the yellow 6-track connector of component 261 and the connector of
component 1303.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on connection 34GG between
components 261 and 1303.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the condition and connection of the connector of component 247.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on connection 34GD between
components 247 and 1303.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
NAV4R_V24_ET004

MULTIMEDIA
Fault finding - Interpretation of parameters86C
86C-55
NAV 4R
Program no.: 0000
Vdiag No.: 24
*RDS: Radio Data SystemPR010
RADIO FIELD INTENSITY
NOTESThere must be no present or stored faults.
Engine stopped, ignition on.
Tune to a known FM or AM station with the vehicle in an open area if possible.
The "Radio field intensity" corresponds to the electrical intensity of the radio signal (FM or AM) received at the
radionavigation tuner input, at the frequency currently selected. It is expressed in dB µV.
It gives an indication of the radio reception level. Below 18 dB µV, the station is considered weak and does not
appear in the list of radio stations.
A low value (< 18 dB µV) on this parameter means that:
–Either the selected station has a weak transmission in the geographical area. This may be due to the
distance from the selected station's transmitter (far from urban area, on motorways) or obstacles interfering
with the transmission of radio waves (mountainous areas, buildings, deep valleys).
–Or, if the reception conditions are good in the geographical area for the selected station, there is a fault on
the vehicle's reception system: one of the components (aerial/aerial amplifier/coaxial connection/radio aerial
connector) is faulty. In this case, refer to ALP 4.
This parameter may be used to compare two vehicles in order to determine if there actually is a vehicle fault.
Summary table of field values and their effect on radio reception:
Radio field intensityAudio
qualityRDS* decoding
(eg.: station names display)Automatic tuning/
Presence in the radio list
PR010 > 18 dBµVOK OK OK
14 dBµV < PR010 < 18 dBµVOK OKNOK
10 dBµV < PR010 < 14 dBµVOKNOK NOK
PR010 < 10 dBµVNOK NOK NOK
AFTER REPAIRRepeat the conformity check from the start.
NAV4R_V24_PR010

MULTIMEDIA
Fault finding - Command summary table86C
86C-56
NAV 4R
Program no.: 0000
Vdiag No.: 24
Fault finding - Command summary table
Tool command Diagnostic tool title
RZ001Fault memory
AC004Speaker test
AC021Display test
AC022CD ejection
VP002Write VIN
VP005Computer configuration

MULTIMEDIA
Fault finding - Dealing with commands
86C
86C-57
NAV 4R
Program no.: 0000
Vdiag No.: 24
Fault finding - Dealing with commands
CLEARING
RZ001 Fault memory:
This command is used to clear faults stored in the navigation computer.
ACTIVATIONS
AUDIO tab
AC004 Speaker test:
This command is used to perform a listening test on the speakers.
DISPLAY tab
AC021 Display test:
This command is used to check that the video display is operating correctly. Three colours are displayed on
the screen: Red, green and blue, and a black mosaic on a white background.
USER SELECTION tab
AC022 CD ejection:
This command is used to eject the CD from the CD reader, and not from the CD changer.

MULTIMEDIA
Fault finding - Customer complaints
86C
86C-61
NAV 4R
Program no.: 0000
Vdiag No.: 24
Fault finding - Customer complaints
NOTESOnly consult the customer complaints after performing a complete check with
the diagnostic tool.
NO DIALOGUE WITH THE COMPUTER ALP 1
THE SCREEN STAYS BLACKALP 2
POOR GUIDANCE/POOR LOCATION/GPS FAULT ALP 3
POOR RADIO RECEPTIONALP 4
CD READ FAULTALP 5
STUCK ON MESSAGE "LOADING GENERAL MAP" ALP 6
THE SYSTEM EMITS BLEEPSALP 7
THE RADIO DOES NOT SWITCH ON AUTOMATICALLY OR GOES OFF
AFTER 20 MINUTESALP 8
POOR/NO TEMPERATURE DISPLAY ALP 9
THE SCREEN DISPLAYS "CD0000" ALP 10

MULTIMEDIA
Fault finding - Customer complaints
86C
86C-62
NAV 4R
Program no.: 0000
Vdiag No.: 24
NOTESOnly consult the customer complaints after performing a complete check with
the diagnostic tool.
THE 6 CD CHANGER DOES NOT WORK ALP 11
NO RADIO AND/OR CD SOUND ALP 12
SATELLITE CONTROLALP 13
FRONT PANEL BUTTON FAULT ALP 14
NO NAVIGATION VOICE MESSAGES ALP 15
THE VOLUME DOES NOT INCREASE WITH THE VEHICLE SPEED ALP 16
NO TRAFFIC INFORMATION MESSAGES APPEAR ON THE SCREEN ALP 17
THE DISPLAY ON THE SCREEN STAYS FROZEN ALP 18

MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-66
NAV 4R
Program no.: 0000
Vdiag No.: 24
ALP 2
CONTINUED
Check that the radio display appears on the
instrument panel dot matrix display (only on
Mégane).
No Yes
Check for + 12 V on connections 46M and 46N
and earth on connections 46BG, 46BH and
46BK of the connector of component 1127.
Are these tests correct?
Yes
Cut the + accessories feed (for at least 1 minute)
then re-activate it.
Is the fault still present?If the connection is faulty and there is a
repair procedure (see Technical
Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair
the wiring, otherwise replace it.
No
NoEnd of fault finding.
In the event of an intermittent
fault, contact the Techline.
YesContact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.

MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-73
NAV 4R
Program no.: 0000
Vdiag No.: 24
ALP 6Stuck on message
Loading general map
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Check for the cartographic map CD in component 261 (commercial vehicle: 662).
After inserting the cartographic map CD in component 261 (commercial vehicle: 662), check that the general map
starts loading:
–message "Loading general map" displayed,
–display: (after 1 minute maximum) "progress percentage" pictogram (eg.: 35 %) in the lower status bar.
Note:
Loading may take up to 15 minutes.
Do not interrupt the loading process (by ejecting CD, switching off equipment, cutting + accessories feed,
etc.).
Loading is complete when the map appears.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
NAV4R_V24_ALP6