battery RENAULT SCENIC 2007 J84 / 2.G Anti Lock Braking System Bosch 8.0 ABS Workshop Manual

ANTI-LOCK BRAKING SYSTEM
Fault finding - Introduction
38C
38C - 6V2 MR-372-J84-38C000$066_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0F
5. FAULT FINDING LOG
You will always be asked for this log:
●when requesting technical assistance from Techline,
●for approval requests when replacing parts for which approval is mandatory,
●to be attached to monitored parts for which reimbursement is requested. The log is needed for warranty
reimbursement, and enables better analysis of the parts removed.
6. SAFETY ADVICE
Safety rules must be observed during any work on a component to prevent any damage or injury:
–make sure that the battery is properly charged to avoid damaging the computers with a low load,
–use the appropriate tools.
–It is forbidden to carry out a road test with the diagnostic tool in dialogue with the ECU because
the ABS and Electronic Brake Distribution functions are deactivated. Braking pressure is
identical on both vehicle axles (risk of a spin under heavy braking). IMPORTANT!IMPORTANT
Any fault on a complex system requires thorough fault finding with the appropriate tools. The
FAULT FINDING LOG, which should be completed during the procedure, enables you to keep
track of the procedure which is carried out. It is an essential document when consulting the
manufacturer.
IT IS THEREFORE MANDATORY TO FILL OUT A FAULT FINDING LOG EACH TIME FAULT FINDING
IS CARRIED OUT.
ABS 8.0X84 4.0

ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
38C
38C - 12V2 MR-372-J84-38C000$396_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0FANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
DF001
PRESENT
OR
STOREDCOMPUTER FEED
1.DEF : Below minimum threshold
2.DEF : Above maximum threshold
3.DEF : Abnormal voltage
NOTESSpecial notes:
The fault is declared present during a road test at a speed of > 6 mph (10 km/h). The
computer signals an external supply fault.
Conditions for applying the fault finding procedure to stored faults:
Apply the fault finding procedure whether the fault is present or stored.
Check the connections and the condition of the battery terminals.
Check the condition and position of the ABS fuses in the engine fuse and relay box.
Check the 50A power fuse in position 5 on the power fuse board.
Check the 25A fuse F13 on the UPC and the correct locking of the grey 4-track PPHI connector (Vdiag 44) or
the 25A fuse F8 on the UPC and the correct locking of the black 6-track CM connector (Vdiag 48).
Check the connection and condition of the tab 1 red wire of the grey connector.
Check the connections on the 26-track connector of the ABS computer.
Check the ABS earths on tracks 1 and 4 (attached under the ABS unit) and carry out an inspection of the entire
ABS wiring.
Check the continuity between the fuses and tracks 2 and 3 of the computer connector (+ Before ignition present
on the tracks) and between the UCH and track 18 of the computer (+ After ignition present on the track).
Clear the computer fault memory. Switch off the ignition.
Switch on the ignition again and carry out another check using the diagnostic tool.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS8.0_V0C_DF001 /ABS8.0_V0D_DF001/ABS8.0_V0E_DF001/ABS8.0_V0F_DF001 ABS 8.0X84 4.0
MR-372-J84-38C000$396_eng.mif

ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
38C
38C - 21V2 MR-372-J84-38C000$396_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0F
DF017
PRESENT
OR
STOREDCOMPUTER
1.DEF : Feed fault or internal electronic fault
2.DEF : Programming / initialisation invalid
NOTESSpecial notes:
The voltage displayed in the parameter (PR005) is the + after ignition feed voltage of
the computer and not the hydraulic unit power feed.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present following a road test at a speed of > 36 mph (60 km/h).
Check the connections and the condition of the battery terminals.
Check the condition and position of the ABS fuses in the engine fuse and relay box.
Check the 50A power fuse in position 5 on the power fuse board.
Check the 25A fuse F13 on the UPC and the correct locking of the grey 4-track PPHI connector (Vdiag 44) or
test the 25A fuse F8 on the UPC and the correct locking of the black 6-track CM connector (Vdiag 48).
Check the connection and condition of the tab 1 red wire of the grey connector.
Check the connections on the 26-track connector of the ABS computer.
Check the ABS earths on tracks 1 and 4 (attached under the ABS unit) and carry out an inspection of the entire
ABS wiring.
Check the continuity between the fuses and tracks 2 and 3 of the computer connector (+ Before ignition present
on the tracks) and between the UCH and track 18 of the computer (+ After ignition present on the track).
Clear the computer fault memory. Switch off the ignition.
Switch on the ignition again and carry out another check using the diagnostic tool.
If the fault is still present, contact the Techline.
2.DEF
NOTESSpecial notes:
No programming for PR020 Vehicle speed at initialisation.
ABS warning light flashing at 8 Hz outside fault finding
conditions.
Run command VP032 and select "Type 1" or "Type 2" according to the information supplied by the diagnostic tool.
Clear the computer fault memory, switch the ignition off and carry out a road test. If the fault is still present, contact
the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS8.0_V0C_DF017 /ABS8.0_V0D_DF017/ABS8.0_V0E_DF017/ABS8.0_V0F_DF017 ABS 8.0X84 4.0

ANTI-LOCK BRAKING SYSTEM
Diagnostic - Fault finding chart
38C
38C - 51V2 MR-372-J84-38C000$924_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0FANTI-LOCK BRAKING SYSTEM
Diagnostic - Fault finding chart
ALP1 No dialogue with the ABS computer
NOTESSpecial notes:
To run fault finding on the vehicle's computers, switch on the ignition in fault
finding mode (forced + after ignition feed). Proceed as follows:
–with the vehicle card in the card reader, press the Start button for more than
5 seconds outside of starting conditions.
Check that the CLIP diagnostic tool is equipped with the latest update available.
Check that the diagnostic tool is not causing the fault by trying to establish dialogue with a computer on another
vehicle. If the tool is not at fault, and dialogue cannot be established with any other computer on the same vehicle,
the cause could be a faulty computer interfering on the multiplex network. Check the battery voltage and carry out
the necessary work to obtain the correct voltage (9.5 V < battery voltage < 17.5 V).
Carry out a fault finding procedure on the multiplex network using the diagnostic tool.
Check the presence and the condition of the ABS fuses on the passenger compartment fuse board and in the
engine fuse box. Check that the computer connector is properly connected and check the condition of its
connections. Check the ABS earths (good condition, not corroded, tightness of the earth screw above the ABS
assembly). Check that the supply to the computer is correct:
–Earth on tracks 1 and 4 of the 26-track connector.
–+ before ignition feed on tracks 2 and 3 of the 26-track connector.
–+ after ignition feed on track 18 of the 26-track connector.
Check that the power supply to the diagnostic socket is correct:
–+ before ignition feed on track 16.
–+ after ignition feed on track 1.
–Earth on tracks 4 and 5.
If dialogue has still not been established after these checks, contact the Techline.
AFTER REPAIRClear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS8.0_V0C_ALP01 /ABS8.0_V0D_ALP01/ABS8.0_V0E_ALP01/ABS8.0_V0F_ALP01 ABS 8.0X84 3.0
MR-372-J84-38C000$924_eng.mif

ANTI-LOCK BRAKING SYSTEM
Diagnostic - Fault finding chart
38C
38C - 63V2 MR-372-J84-38C000$924_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0F
ABS8.0_V0C_ALP13 /ABS8.0_V0D_ALP13/ABS8.0_V0E_ALP13/ABS8.0_V0F_ALP13
ALP 13Intermittent illumination of the brake, ABS, SERVICE and STOP
fault warning lights and the message “brake failure” on the
instrument panel with no fault codes in the computer
NOTESOnly consult this customer complaint after a complete check with the diagnostic
tool.
Check the condition and connection of the
battery terminals.
Is the battery in good condition?
YES
Check the 50A power fuse in position 5 on
the power fuse board. Check fuse F13 (25A)
on the UPC and the correct locking of the
grey 4-track PPH1 connector (Vdiag 44) or
the 25A fuse F8 on the UPC and the correct
locking of the black 6-track CM connector
(Vdiag 48 or higher).
Are the fuses and connectors correct?
YES
Check the connection and condition of the tab
1 red wire of the grey connector.
Is the connector correct?
YES
NOClean the battery terminals.
NOIf the connector is faulty and there is a repair
procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions
for repair), repair the connector, otherwise
replace the wiring.
Replace any faulty fuses. Switch on the ignition
again.
Is the replaced fuse or fuses correct?
NO
Check the insulation to earth between:
–fuse 50A and track 2 of the computer
–fuse 25A and track 3 of the computer
Are the connections correct?
NO YES
Contact the Techline.
If the connection(s) are faulty and there is a repair method
(see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
NO
If the connector is faulty and there is a repair method (see Technical
Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the connector, otherwise replace the wiring.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.