lights RENAULT SCENIC 2008 J84 / 2.G Passenger Comparment Connection Unit User Guide

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-53
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-53V9 MR-372-J84-87B000$215.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
UCH programming procedure
–Run the Multiplex network test.
–Switch on the side lights.
–Establish dialogue with the UCH.
–Select the menu repair mode.
–Select the menu secure programming.
–Select line SC004 Program UCH.
Follow the instructions on the CLIP diagnostic tool.
In "not connected" mode, when the CLIP diagnostic tool displays the programming key, make a note of this key
and the VIN.
To obtain the immobiliser code, see Technical Note 5037A, Code delivery procedure.
Operations to be carried out after programming the UCH
●Enter the vehicle VIN in the computer using the command VP004 Enter VIN.
●After programming the UCH, allocate all of the cards using command SC006 Card allocation.
●Configure the equipment as present or not present on the vehicle using the commands
(see Configuration and programming). IMPORTANT
In "not connected" mode, the programming key can only be used for a limited amount of time, as indicated by
the CLIP diagnostic tool. After this time, the programming key and associated immobiliser code are no longer
valid. The operation must be restarted from the beginning.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-62
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-62V9 MR-372-J84-87B000$215.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
8/ UCH TYPE CONFIGURATION PROCEDURE (SC008)
8.1 Vdiag 44, 48
This procedure will enable the UCH to be configured in relation to the vehicle to provide optimum running.
–Click on the Repair mode and in the Programming menu,
–confirm line SC008 UCH type,
–follow the procedure and enter the following data:
–CF097 Vehicle type (3-door/4-door/5-door/cabriolet/extended MPV/MPV/Estate),
–confirm, follow the procedure and enter the following data:
–CF010 Hands-free function (WITH or WITHOUT),
–CF023 Tyre pressure monitoring system function (WITH or WITHOUT),
–CF057 Type of heating resistors (NONE, 1000 W, or 1800 W),
–CF019 Type of air conditioning (HEATING, AUTOMATIC, MANUAL),
–CF027 Type of windscreen (TINTED, HEAT INSULATING),
–CF035 Rain/light sensor (WITH or WITHOUT),
–CF014 Daytime running lights (WITH or WITHOUT),
–CF022 Factory fitted perimeter protection (WITH or WITHOUT): function only available on vehicles for the
Mexican market,
–CF173 One-touch window(s)/Sunroof (WITH or WITHOUT),
–confirm, follow the procedure and enter the following data:
–CF036 Selective opening of the opening elements (WITH or WITHOUT) Only if CF010 = WITHOUT
–confirm, follow the procedure and enter the following data:
–CF085 Valet card function (WITH or WITHOUT) Function only available in Mexico,
–(This status will only be available if the following conditions are met: CF036 Selective opening of opening
elements = WITH),
–check that the options configured are those desired and finish.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-63
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-63V9 MR-372-J84-87B000$215.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
8.2 Vdiag 4C and 4D:
This procedure will enable the UCH to be configured in relation to the vehicle to provide optimum running.
–Click on the Repair mode and in the Programming menu,
–confirm line SC008 UCH type,
–follow the procedure and enter the following data:
CF097 Vehicle type (3-door/4-door/5-door/cabriolet/extended MPV/MPV/Estate).
CF011 Gearbox type (BVA or BVM).
CF020 Type of driving style (Right-hand or Left-hand).
CF028 Engine type (F or K)
–confirm, follow the procedure and enter the following data:
CF010 Hands-free function (WITH or WITHOUT),
CF023 Tyre pressure monitoring system (WITH or WITHOUT),
CF057 Type of heating resistors (NONE, 1000 W, or 1800 W),
CF019 Type of air conditioning (HEATING, AUTOMATIC, MANUAL),
CF027 Type of windscreen (TINTED, HEAT INSULATING),
CF087 Front fog light (WITH or WITHOUT),
CF014 Daytime running lights (WITH or WITHOUT),
CF012 Rain sensor (WITH or WITHOUT),
CF029 External temperature sensor (WITH or WITHOUT).
–confirm, follow the procedure and enter the following data:
CF036 Selective opening of opening elements (WITH or WITHOUT): Only if CF010 = WITHOUT.
CF016 PAX system type tyre (WITH or WITHOUT): Only if CF097 = MPV or extended MPV or cabriolet and if
CF023 = WITH.
CF100 Deadlocking (WITH or WITHOUT).
CF013 Light sensor (WITH or WITHOUT): Only if CF014 = WITHOUT.
CF022 Factory fitted
perimeter protection (WITH or WITHOUT). Function only available on vehicles sold in
Mexico. CF083 One touch window(s) (WITH or WITHOUT): Absent if CF097 = Cabriolet.
–confirm, follow the procedure and enter the following data:
CF085 Valet card function (WITH or WITHOUT) Function only available in Mexico. Only if CF036 = WITH and
CF023 = WITHOUT.
–check that the options configured are those desired and finish.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-64
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-64V9 MR-372-J84-87B000$215.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
8.3 Vdiag 4F and 50:
This procedure will enable the UCH to be configured in relation to the vehicle to provide optimum running.
–Click on the Repair mode and in the Programming menu,
–confirm line SC008 UCH type,
–follow the procedure and enter the following data:
–CF097 Vehicle type (3-door/4-door/5-door/cabriolet/Estate) except for Scénic (extended MPV/MPV).
–confirm, follow the procedure and enter the following data:
CF010 Hands-free function (WITH or WITHOUT),
CF023 Tyre pressure monitoring system (WITH or WITHOUT),
CF057 Type of heating resistors (NONE, 1000 W, or 1800 W),
CF019 Type of air conditioning (HEATING, AUTOMATIC, MANUAL),
CF027 Type of windscreen (TINTED, HEAT INSULATING),
CF035 Rain/light sensor (WITH or WITHOUT),
CF014 Daytime running lights (WITH or WITHOUT),
CF189 Protection type (TYPE 1, TYPE 2 or WITHOUT): TYPE 1 = with factory
fitted perimeter protection, TYPE
2 = with Cobra type alarm and WITHOUT = without factory fitted perimeter protection and without Cobra alarm.
–confirm, follow the procedure and enter the following data:
CF173 One-touch window(s)/sunroof (1 OTW* phase 1/1 OTW* phase 2/2 or 4 OTW*/WITHOUT): Absent if
CF097 = Cabriolet.
1 OTW* phase 1 = 1 driver side one touch window with a phase 1 bodywork vehicle.
1 OTW* phase 2 = 1 driver side one touch window with a phase 2 bodywork vehicle.
2 or 4 OTW = 2 or 4 one touch windows.
WITHOUT = no one touch windows on the vehicle.
–confirm, follow the procedure and enter the following data:
CF188 Production number type (Jxxxxxx or OTHER): only if CF097 = 4-doors and CF173 = 1 OTW* Phase 1.
The production number is located on the oval plate on the vehicle's right-hand side B-pillar. The production number
consists of 7 characters: 1 letter indicating the production plant followed by 6 figures.
–If the production number starts with the letter J, select Jxxxxxx.
–If the production number does not start with the letter J, select Other.
–Confirm, follow the procedure and enter the following data:
CF036 Selective opening of opening elements (WITH or WITHOUT): Only if CF010 = WITHOUT CF016 PAX
System type tyre (WITH or WITHOUT): Only if CF097 = MPV or Extended MPV and if CF023 = WITH.
–confirm, follow the procedure and enter the following data:
CF085 Valet card function (WITH or WITHOUT): Only if CF036 = WITH and CF023 = WITHOUT.
–check that the options configured are those desired and finish.
OTW*: One-touch window(s)IMPORTANT
Only configure WITH valet card function when the vehicle is electrically pre-equipped with the valet option.
Incorrect configuration may cause certain pieces of equipment to malfunction.
Note:
After having finished the UCH configuration, run command AC037 "TRANSMITTING AERIALS FAULT FINDING"
and check that there are no faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-66
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-66V9 MR-372-J84-87B000$215.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
The UCH configurations performed in accordance with the vehicle's equipment level are configured using
the CLIP tool:
Configuration
readingConfigurationName of
configurationChoice of
configurationVdiag
LC001Hands-free functionSC008 UCH typeWITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC002External temperature
sensorCF029WITH/WITHOUT 4C, 4D, 4F and 50
LC003DeadlockingCF009WITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC004One-touch window(s)SC008 UCH typeWITH/WITHOUT 4C and 4D
LC005Gearbox typeCF011Manual/
Automatic44, 48, 4C, 4D, 4F
and 50
LC006Rain detectorSC008 UCH typeWITH/WITHOUT 44, 48, 4C, 4D
LC007Light sensorSC008 UCH typeWITH/WITHOUT 44, 48, 4C, 4D
LC008Daytime running lightsCF014WITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC009Hazard warning lights
illuminated upon impactAutomatic
configurationWITH/WITHOUT 44, 48, 4C, 4D
LC010Tyre type Run flat tyreSC008 UCH typeWITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC011Vehicle typeSC008 UCH typeCabriolet/3-door/
All except E and
C44, 48, 4C, 4D
LC012Automatic relockingCF018WITH/WITHOUT 44, 48, 4C, 4D
LC013Type of air conditioningSC008 UCH typeHeating/
Automatic/
Manual 44, 48, 4C, 4D, 4F
and 50
LC014Type of driving styleCF020LEFT-HAND/
RIGHT-HAND 44, 48, 4C, 4D, 4F
and 50
LC015Front fog lightsCF021WITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC016Valet card functionSC008 UCH type WITH/WITHOUT 4C, 4D, 4F and 50

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-67
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
87B
87B-67V9 MR-372-J84-87B000$215.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
UCH configurations (continued):
T.O*: Sunroof.Configuration
readingConfigurationName of
configurationChoice of
configurationVdiag
LC017Tyre Pressure Monitor
FunctionSC008 UCH typeWITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC018Hazard warning lights
switched on by ABS CF024WITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC019Rear screen wiper park
position controlAutomatic
configurationWITH/WITHOUT 44, 48, 4C, 4D
LC020Factory fitted perimeter

protection SC008 UCH typeWITH/WITHOUT 4C, 4D, 4F and 50
LC021Type of windscreen
SC008 UCH typeTINTED/HEAT
INSULATING44, 48, 4C, 4D, 4F
and 50
LC023 Engine type CF028F ENGINE/K
ENGINE/M
ENGINE44, 48, 4C, 4D, 4F
and 50
LC025See-me-home lighting CF032WITH/WITHOUT 44, 48, 4C, 4D
LC029 Selective door opening SC008 UCH typeWITH/WITHOUT44, 48, 4C, 4D, 4F
and 50
LC030Heating resistor type SC008 UCH typeNONE/1000 W/
1800 W 44, 48, 4C, 4D, 4F
and 50
LC035Child safety lockSC016 Child safety
lockWITH/WITHOUT 4C, 4D, 4F and 50
Automatic
configurationWITH/WITHOUT 44 and 48
LC041New vehicle storage modeVP016 ACTIVE/
INACTIVE 4F and 50
LC044 Rain/light sensor SC008 UCH typeWITH/WITHOUT 4F and 50
LC064 Rear screen wiper CF166 WITH/WITHOUT 4F and 50
LC070One-touch window(s)/
sunroof SC008 UCH typeWITH/WITHOUT 4F and 50
LC122Rear access aerialsCF224WITH/WITHOUT 50

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-82
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-82V9 MR-372-J84-87B000$301.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
DF012
PRESENT
OR
STOREDRIGHT-HAND DIRECTION INDICATOR CIRCUIT
CO.0: Open circuit or short circuit to earth
1.DEF: Bulbs not working or open circuit
NOTESConditions for applying the fault finding procedure to a stored fault:
If the fault appears after action on the right-hand direction indicator control stalk, apply
this fault finding procedure.
Special note:
The fault becomes stored after changing a bulb.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Check the bulbs.
Replace them, if necessary.
Check the condition and connection of the right-hand headlight connectors of the right-hand indicator
repeater and the rear right-hand light.
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check for earth on components 226 and 267.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check for earth on connection MAQ of component 172.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
With the command running, check for + 12 V on connection 64D of components 226 and 267.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check the condition and connection of connector PP3 and connector PP1 on the UCH.
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connection:
●Connection code 64D, between components 645 and 172.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If correct, check the connection between the UCH and front and rear lights (see wiring diagram), check the bulbs
again and if still not correct, replace the rear lights(s).
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF012 /UCH_V48_DF012/UCH_V4C_DF012/
UCH_V4D_DF012/UCH_V4F_DF012/UCH_V50_DF012

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-83
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
87B
87B-83V9 MR-372-J84-87B000$301.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
DF013
PRESENT
OR
STOREDLEFT-HAND DIRECTION INDICATOR CIRCUIT
CO.0: Open circuit or short circuit to earth
1.DEF: Bulbs not working or open circuit
NOTESConditions for applying the fault finding procedure to a stored fault:
If the fault appears after action on the left-hand direction indicator control stalk, then
apply this fault finding procedure.
Special note:
The fault becomes stored after changing a bulb.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Check the bulbs.
Replace them, if necessary.
Check the condition and connection of the left-hand headlight connector, the left-hand repeater and the rear
left-hand light.
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check for earth on components 227 and 268.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check for earth on connection MZ of component 173.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
With the command running, check for + 12 V on connection 64C of components 227 and 268.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check the condition and connection of connector PP3 and connector PP2 on the UCH.
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connection:
●Connection code 64C between components 645 and 173.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If correct, check the connection between the UCH and front and rear lights (see wiring diagram), check the bulbs
again and if still not correct, replace the rear lights(s).
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF013 /UCH_V48_DF013/UCH_V4C_DF013/
UCH_V4D_DF013/UCH_V4F_DF013/UCH_V50_DF013

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -135
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -135V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
LIGHTING FUNCTION
Sub-function: Lighting command
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-
functionParameter or
Status
checked Action Display and Notes Fault finding
Lighting
controlET081:Lighting switch
positionOFF
SIDE
DIPPED
MAIN BEAM HEADLIGHTS
HAZARD LIGHTS In the event of a fault,
refer to the
interpretation of status
ET081.
ET115:Request to switch
on lights by light
sensor PRESENT
ABSENTIn the event of a fault,
consult the
interpretation of status
ET115.
ET169:EngineSTOPPEDIn the event of a fault,
refer to the
interpretation of
status ET169.
ET113:Automatic lighting
button DEPRESSED
RELEASED In the event of a fault,
consult the
interpretation of
status ET113.
ET111:Front fog lights
requestPRESENT
ABSENT In the event of a fault,
consult the
interpretation of
status ET111.
ET082:Rear fog lights
requestPRESENT
ABSENT In the event of a fault,
consult the
interpretation of
status ET082.
ET085:Hazard warning
lights buttonDEPRESSED
RELEASED In the event of a fault,
refer to the
interpretation of
status ET085.
ET083:Left-hand indicator
requestPRESENT
ABSENT In the event of a fault,
refer to the
interpretation of
status ET083.
ET084:Right-hand indicator
requestPRESENT
ABSENT In the event of a fault,
refer to the
interpretation of
status ET084.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
87B
87B -141
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
87B
87B -141V9 MR-372-J84-87B000$430.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
*Trip computer: Not authorised
*Sunroof: Tool status Diagnostic tool title Vdiag
ET066Card detected button
V44, V48, V4C,
V4D, V4F, V50 ET067Card button press recognised
ET068Most recently locked by
ET069Most recently unlocked by
ET070Start button
ET071 Unprogrammed steering lock
ET072Steering lock
ET073Steering lock sensor signal
ET075+ Accessories present
ET077Wiper stalk position
ET078Windscreen washer request
ET079Rear screen washer request
ET080Rear screen wiper request
ET081Lighting switch position
ET082Rear fog lights request
ET083Left-hand indicator request
ET084Right-hand indicator request
ET085Hazard warning lights button
ET086Electric child safety lock V44, V48, V4C
ET087Sunroof*/one touch electric window authorisation
V44, V48, V4C,
V4D, V4F, V50 ET088Deadlocking activation source
ET090Deadlocking deactivation source
ET096Wiper stalk intermittent speed ring position
ET097Rear screen wiper park position
ET098ADAC* button
ET108Automatic gearbox lever position
ET109Reverse gear engaged
ET110UCH request to injection or Protection and Switching Unit
ET111Front fog lights request
ET112Interior lighting control