display RENAULT SCENIC 2010 J95 / 3.G Engine And Pheripherals DCM 1.2 Injection Repair Manual

13B-84
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V10 MR-372-J84-13B100$110.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF052
CONTINUED
DF052
PRESENTThe injectors are not defective.
Check the condition and connection of the injection computer (brown 48-track)
connector B.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A,
Repairing electrical wiring, Wiring: Precautions for repair), repair the connector(s),
otherwise replace the wiring.
Check the insulation, the continuity and the absence of interference resistance on
the following connections:
–3L between components 193 and 120,
–3KW between components 193 and 120,
–3LA between components 194 and 120,
–3KX between components 194 and 120,
–3LB between components 195 and 120,
–3KY between components 195 and 120,
–3LC between components 196 and 120,
–3KZ between components 196 and 120.
If the connection or connections are faulty and there is a repair procedure
(see Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
If the fault is still present, contact the Techline.
DF052
STOREDInjector(s) defective.
Replace the injector identified by faults DF026 Cylinder 1 injector control circuit to
DF029 Cylinder 4 injector control circuit if any are present.
If none of the faults identifying the defective injector circuit are present:
–switch off the ignition,
–reconnect one of the four injectors,
–switch on the ignition again.
If the fault recurs as present, replace the reconnected injector, component code 193,
194, 195, or 196 (see MR 364 (Mégane II), MR 370 (Scénic II), MR 385 (Modus), MR
392 (Clio III), MR 411 (New Twingo), MR 417 (Kangoo 2), Mechanical, 13B,
Diesel injection, Diesel injector: Removal - Refitting).
Follow the same procedure for the other injectors.

13B-85
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V10 MR-372-J84-13B100$110.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF053
PRESENT
OR
STOREDRAIL PRESSURE REGULATION FUNCTION
1.DEF: at minimum stop
2.DEF: at maximum stop
3.DEF: below minimum threshold
4.DEF: above maximum threshold
5.DEF: high flow current < minimum
6.DEF: high flow current > maximum
7.DEF: low flow current < minimum
8.DEF: low flow current > maximum
NOTESPriorities when dealing with a number of faults:
–DF098 Fuel temperature sensor circuit,
–DF007 Rail pressure sensor circuit.
Special note. If DF053, the engine may stop with the level 2 warning light illuminated
with the message Faulty injection displayed on the instrument panel.
Conditions for applying fault finding procedures to stored faults:
The fault is present with the engine running.
See the Technical Note Wiring Diagrams for the vehicle.
Check the presence and conformity of the fuel, run TEST 13: Diesel fuel conformity check.
Check the connection and condition of the flow actuator connector, component code 1105.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check for + 12 V (after relay) on connection 3FB1 or 3FB2 (for New Twingo) or 3FB3 (for Kangoo 2) of
component 1105.
Check the connection and condition of connector B (brown 48-track) of the injection computer, component
code 120.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance between connections 3HI and 3FB1 or 3FB2 (for New Twingo) or 3FB3 (for Kangoo 2)
of component 1105.
If the resistance of the flow actuator is not between 4.8 Ω and 5.8 Ω at 20
°C, replace the flow actuator, component
code 1105 (see MR 364 (Mégane II), MR 370 (Scénic II), MR 385 (Modus), MR 392 (Clio III), MR 411
(New Twingo), MR 417 (Kangoo 2), Mechanical, 13B, Diesel injection, Flow actuator: Removal - Refitting).
DCM1.2_V48_DF053/DCM1.2_V4C_DF053/DCM1.2_V50_DF053/DCM1.2_V54_DF053/DCM1.2_V58_DF053/DCM1.2_V5C_DF053

13B-86
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V10 MR-372-J84-13B100$110.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF053
CONTINUED
Check the insulation and continuity of the following connection:
–3HI between components 1105 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Run Test 1: Low pressure circuit check.
Run Test 6: High pressure system check.
Run Test 8: Injector return flow.
If the fault is still present contact Techline.

13B-87
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V10 MR-372-J84-13B100$110.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF056
PRESENT
OR
STOREDAIR FLOWMETER CIRCUIT1.DEF: Permanent low level
2.DEF: Permanent high level
3.DEF: Below minimum threshold
4.DEF: Above maximum threshold
5.DEF: At minimum stop
6.DEF: At maximum stop
NOTESSpecial notes:
If fault DF056 is present: air flow regulation stops and the EGR valve is closed.
See the Technical Note Wiring Diagrams for the vehicle.
Check that the air filter is not blocked.
Check that the air filter is not clogged and that the air inlet system is not blocked between the air filter outlet
and the inlet manifold.
Run TEST 5: Inlet circuit check.
Run TEST 11: Air line at the turbocharger.
Check the connection and condition of the air flowmeter connector, component code 799.
Check the connection and condition of connector B (brown 48-track) of the injection computer, component
code 120.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check for + 5 V on connection 3KJ of component 799.
Check for earth on connection 3DW of component 799.
Check the insulation and continuity of the following connections:
–3KJ between components 799 and 120,
–3DW between components 799 and 120,
–3DV between components 799 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the fault is still present, replace the air flowmeter, component code 799 (see MR 364 (Mégane II), MR 370
(Scénic II), MR 385 (Modus), MR 392 (Clio III), MR 411 (New Twingo), MR 417 (Kangoo 2), Mechanical, 12A,
Fuel mixture, Air flowmeter: Removal - Refitting).
If the fault is still present, contact the Techline.
DCM1.2_V48_DF056/DCM1.2_V4C_DF056/DCM1.2_V50_DF056/DCM1.2_V54_DF056/DCM1.2_V58_DF056/DCM1.2_V5C_DF056

13B-88
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V10 MR-372-J84-13B100$110.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF057
PRESENT
OR
STOREDWATER IN DIESEL FUEL DETECTOR CIRCUIT
CO.1: Open circuit or short circuit to + 12 V
CC.0: Short circuit to earth
1.DEF: above maximum threshold
NOTESSpecial notes:
–If water is detected downstream of the diesel filter, the high pressure pump
and the injectors may be damaged.
Use bornier Elé. 1681 for all operations on the connector of the engine management
computer.
See the Technical Note Wiring Diagrams for the vehicle.
Check the connections of the water in diesel fuel sensor, component code 414.
Check the connections of the engine management computer, component code 120.
If the connector(s) are faulty and there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the connector(s), otherwise replace the wiring.
With the ignition on, check for +12 V on connections 3FB1 and 3FB2 (for New Twingo) or AP15 (for Kangoo 2)
of component 414.
Check for earth on the following connections:
–M or 3WU (for New Twingo) of component 120.
–MH and MW (for Kangoo 2) of component 414.
Check the continuity of the following connections:
–3WT between components 414 and 120,
–M between components 414 and 120,
–3FB1 between components 414 and 1337.
(only for New Twingo):
–3WT between components 414 and 120,
–3WU between components 414 and 120,
–3FB2 between components 414 and 238.
(only for Kangoo 2):
–AP15 between components 414 and 1337,
–3WT between components 414 and 1337,
–MH and MW between earth and component 414.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
DCM1.2_V48_DF057/DCM1.2_V4C_DF057/DCM1.2_V50_DF057/DCM1.2_V54_DF057/DCM1.2_V58_DF057/DCM1.2_V5C_DF057

13B-89
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V10 MR-372-J84-13B100$110.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF057
CONTINUED
If the fault is still present, replace the diesel filter (see MR 364 (Mégane II), MR 370 (Scénic II), MR 385 (Modus),
MR 392 (Clio III), MR 411 (New Twingo), MR 417 (Kangoo 2), Mechanical, 13A, Fuel supply, Fuel filter:
Removal - Refitting).
If the fault is still present, contact the Techline.

13B-90
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V10 MR-372-J84-13B100$110.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF059
PRESENT
OR
STOREDCOMBUSTION MISFIRES ON CYLINDER 1
NOTESSpecial notes:
If fault DF059 is present: there is engine noise and jerking, the engine runs on three
cylinders, the engine speed is held at 1000 rpm, the engine performance is reduced to
75%, and the level 1 warning light illuminates.
Conditions for applying fault finding procedures to stored faults:
The fault is present with the engine idling.
Priorities when dealing with a number of faults:
–DF026 Cylinder 1 injector control circuit (CC or CO),
–DF053 Rail pressure regulation function.
Check the presence and conformity of the fuel. Run TEST 13: Diesel fuel conformity check.
Run TEST 3 Injector check.
Run TEST 7 High pressure circuit sealing check.
Check the engine compression.
Repair if necessary.
Check the valve clearance and adjust if necessary.
Check the inlet ducts, as well as the EGR valve, and clean them if necessary (see Technical Note 3916 Cleaning
the EGR solenoid valve).
If the fault is still present, replace the injector, component code 193 (see MR 364 (Mégane II), MR 370 (Scénic II),
MR 385 (Modus), MR 392 (Clio III), MR 411 (New Twingo), MR 417 (Kangoo 2), Mechanical, 13B, Diesel
injection, Diesel injector: Removal - Refitting).
DCM1.2_V48_DF059/DCM1.2_V4C_DF059/DCM1.2_V50_DF059/DCM1.2_V54_DF059/DCM1.2_V58_DF059/DCM1.2_V5C_DF059

13B-91
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V10 MR-372-J84-13B100$110.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF060
PRESENT
OR
STOREDMISFIRING ON CYLINDER 2
NOTESSpecial notes:
If fault DF060 is present: there is engine noise and jerking, the engine runs on three
cylinders, the engine speed is held at 1000 rpm, the engine performance is reduced to
75%, and the level 1 warning light illuminates.
Conditions for applying fault finding procedures to stored faults:
The fault is present with the engine idling.
Priorities when dealing with a number of faults:
–DF027 Cylinder 2 injector control circuit (CC or CO),
–DF053 Rail pressure regulation function.
Check the presence and conformity of the fuel. Run TEST 13: Diesel fuel conformity check.
Run TEST 3 Injector check.
Run TEST 7 High pressure circuit sealing check.
Check the engine compression.
Repair if necessary.
Check the valve clearance and adjust if necessary.
Check the inlet ducts, as well as the EGR valve, and clean them if necessary (see Technical Note 3916 Cleaning
the EGR solenoid valve).
If the fault is still present, replace the injector, component code 194 (see MR 364 (Mégane II), MR 370 (Scénic II),
MR 385 (Modus), MR 392 (Clio III), MR 411 (New Twingo), MR 417 (Kangoo 2), Mechanical, 13B, Diesel
injection, Diesel injector: Removal - Refitting).
DCM1.2_V48_DF060/DCM1.2_V4C_DF060/DCM1.2_V50_DF060/DCM1.2_V54_DF060/DCM1.2_V58_DF060/DCM1.2_V5C_DF060

13B-92
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V10 MR-372-J84-13B100$110.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF061
PRESENT
OR
STOREDMISFIRING ON CYLINDER 3
NOTESSpecial notes:
If fault DF061 is present: there is engine noise and jerking, the engine runs on three
cylinders, the engine speed is held at 1000 rpm, the engine performance is reduced to
75%, and the level 1 warning light illuminates.
Conditions for applying fault finding procedures to stored faults:
The fault is present with the engine idling.
Priorities when dealing with a number of faults:
–DF028 Cylinder 3 injector control circuit (CC or CO),
–DF053 Rail pressure regulation function.
Check the presence and conformity of the fuel. Run TEST 13: Diesel fuel conformity check.
Run TEST 3 Injector check.
Run TEST 7 High pressure circuit sealing check.
Check the engine compression.
Repair if necessary.
Check the valve clearance and adjust if necessary.
Check the inlet ducts, as well as the EGR valve, and clean them if necessary (see Technical Note 3916 Cleaning
the EGR solenoid valve).
If the fault is still present, replace the injector, component code 195 (see MR 364 (Mégane II), MR 370 (Scénic II),
MR 385 (Modus), MR 392 (Clio III), MR 411 (New Twingo), MR 417 (Kangoo 2), Mechanical, 13B, Diesel
injection, Diesel injector: Removal - Refitting).
DCM1.2_V48_DF061/DCM1.2_V4C_DF061/DCM1.2_V50_DF061/DCM1.2_V54_DF061/DCM1.2_V58_DF061/DCM1.2_V5C_DF061

13B-93
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V10 MR-372-J84-13B100$110.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF062
PRESENT
OR
STOREDMISFIRING ON CYLINDER 4
NOTESSpecial notes:
If fault DF062 is present: there is engine noise and jerking, the engine runs on three
cylinders, the engine speed is held at 1000 rpm, the engine performance is reduced to
75%, and the level 1 warning light illuminates.
Conditions for applying fault finding procedures to stored faults:
The fault is present with the engine idling.
Priorities when dealing with a number of faults:
–DF029 Cylinder 4 injector control circuit (CC or CO),
–DF053 Rail pressure regulation function.
Check the presence and conformity of the fuel. Run TEST 13: Diesel fuel conformity check.
Run TEST 3 Injector check.
Run TEST 7 High pressure circuit sealing check.
Check the engine compression.
Repair if necessary.
Check the valve clearance and adjust if necessary.
Check the inlet ducts, as well as the EGR valve, and clean them if necessary (see Technical Note 3916 Cleaning
the EGR solenoid valve).
If the fault is still present, replace the injector, component code 196 (see MR 364 (Mégane II), MR 370 (Scénic II),
MR 385 (Modus), MR 392 (Clio III), MR 411 (New Twingo), MR 417 (Kangoo 2), Mechanical, 13B, Diesel
injection, Diesel injector: Removal - Refitting).
DCM1.2_V48_DF062/DCM1.2_V4C_DF062/DCM1.2_V50_DF062/DCM1.2_V54_DF062/DCM1.2_V58_DF062/DCM1.2_V5C_DF062