engine RENAULT SCENIC 2010 J95 / 3.G Petrol Injection S3000 Injection Workshop Manual

PETROL INJECTION
Fault finding - Conformity check
17B
17B-149
PETROL INJECTION
Fault finding - Conformity check
17B
17B-149V9 MR-372-J84-17B050$517.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54
FUEL CIRCUIT SUB-FUNCTION (continued 2):
NOTESOnly perform this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine warm, idling.
Order FunctionParameter or Status Checked
or ActionDisplay and notes Fault finding
7
RichnessPR138:Richness correctionIn loop mode, the
richness correction
corrects the injection
duration to obtain a
fuel mixture as close
as possible to a
richness of 1. The
richness correction
value varies around
50 between 0 and
100.
0 <PR138 <100%WITHOUT
8ET300:Richness regulationACTIVE
INACTIVEWITHOUT
9ET056:Richness double loopACTIVEIn the event of a fault,
apply the
interpretation of
ET056 Double
richness loop.
10
RichnessPR144:Self-adapting
richness offsetPR624≈ 128
This parameter is
used to detect any
tendency of the
injection system to
increase or decrease
the richness.
WITHOUT
11 PR143:Self-adapting
richness gainPR625≈ 128
This parameter is
used to detect any
tendency of the
injection system to
increase or decrease
the richness.
12 Injection PR101:Duration of injectionIdling
2.4 µs < PR101
<4.3µs
13Fuel
consumption.PR103:Instantaneous fuel
consumption0 l/h < PR103 < 50 l/h

PETROL INJECTION
Fault finding - Conformity check
17B
17B-150
PETROL INJECTION
Fault finding - Conformity check
17B
17B-150V9 MR-372-J84-17B050$517.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54
SUB-FUNCTION: FUEL CIRCUIT (continued 3):
NOTESOnly perform this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine warm, idling.
Order FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
14 Fuel pump ET047:Fuel pump
control circuitACTIVE If INACTIVE,
apply the
interpretation for
DF085 Fuel
pump relay
control circuit.
15
IN LPG
ACTIVATED
MODEET561:Operating
modePetrol
Then LPG
In the event of a
fault, (see 17C,
3000 LPG
injection). 16 ET067:LPG readyWith LPG YESWithout LPG
NO by default
17 ET073:Conditions for
switching to
LPG modeWith LPG
AUTHORISEDWithout LPG
INHIBITED by
default
18 ET068:LPG tank
emptyWith LPG "NO"Without LPG
NO by default
19 ET066:LPG faultWith LPG "NO"Without LPG
NO by default
20 ET071:Transition
from petrol
mode to LPG
modeWith LPG
IN PROGRESS
then
COMPLETEWithout LPG
COMPLETE by
default
21 ET072:Transition
from LPG
mode to petrol
modeWith LPG IN
PROGRESSWithout LPG
COMPLETE by
default

PETROL INJECTION
Fault finding - Conformity check
17B
17B-151
PETROL INJECTION
Fault finding - Conformity check
17B
17B-151V9 MR-372-J84-17B050$517.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54
EMISSION CONTROL/OBD SUB-FUNCTION:
NOTESOnly perform this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine warm, idling.
Order FunctionParameter or Status Checked
or ActionDisplay and notes Fault finding
1
Oxygen sensorPR098:Upstream oxygen
sensor voltage50 mV < PR098
<800mVIn the event of a fault,
apply the
interpretation of
PR098 Upstream
oxygen sensor
voltage.
2 PR099:Downstream oxygen
sensor voltagePR099≈ 480 mVIn the event of a fault,
apply the
interpretation of
PR099 Downstream
oxygen sensor
voltage.
3
CanisterET050:Canister bleed
controlINACTIVEIn the event of a fault,
apply interpretation of
DF549 Canister
bleed circuit. 4 PR102:Canister bleed
solenoid valve OCR0% <PR102 <100%
5
Oxygen sensorAC018:Upstream O
2 sensor
heatingThe upstream
oxygen sensor
should heat upIn the event of a fault
apply the
interpretation of
DF601 Upstream
oxygen sensor
heating power
circuit.
6AC019:Downstream O
2
sensor heatingThe downstream
oxygen sensor
should heat upIn the event of a fault,
apply interpretation of
DF602 Downstream
oxygen sensor
heating power
circuit.

PETROL INJECTION
Fault finding - Conformity check
17B
17B-152
PETROL INJECTION
Fault finding - Conformity check
17B
17B-152V9 MR-372-J84-17B050$517.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54
EMISSION CONTROL / OBD SUBFUNCTION (cont.):
NOTESOnly perform this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine warm, idling.
Order FunctionParameter or Status Checked
or ActionDisplay and notes Fault finding
7
Oxygen sensor
(continued)ET052:Upstream
Upstream O
2 sensor
heatingINACTIVEIn the event of a fault
apply the interpretation of
DF601 Upstream
oxygen sensor heating
power circuit.
8ET053:Upstream
Downstream O
2
sensor heatingINACTIVEIn the event of a fault,
apply interpretation of
DF602 Downstream
oxygen sensor heating
power circuit.
9CanisterAC017:Canister bleed
solenoid valveThe canister
bleed solenoid
valve should be
heard running.In the event of a fault,
apply interpretation of
DF549 Canister bleed
circuit.
10
Fault findingET617:Upstream oxygen
sensor OBD fault
findingINACTIVE None
11 ET619:Fuel circuit OBD fault
findingINACTIVE None
12 ET581:Petrol combustion
misfire fault findingINACTIVE None
13 Fault finding ET340:Request by automatic
transmission to light
up the OBD warning
lightINACTIVEIf ACTIVE, apply the
interpretation of fault
DF099 Automatic
gearbox or sequential
gearbox connection via
the multiplex network.
14
RichnessET300:Richness regulationACTIVE
INACTIVEWITHOUT
15 ET056:Richness double loopACTIVEIn the event of a fault,
apply the interpretation of
ET056 Double richness
loop.

PETROL INJECTION
Fault finding - Conformity check
17B
17B-153
PETROL INJECTION
Fault finding - Conformity check
17B
17B-153V9 MR-372-J84-17B050$517.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54
DRIVER PARAMETERS SUB-FUNCTION:
NOTESOnly perform this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine warm, idling.
Order FunctionParameter or Status Checked
or ActionDisplay and notes Fault finding
1
Motorised
throttleET051:Throttle stop
programmingCOMPLETED
Run command
RZ005
Programming. If the
parameters or
statuses are still not
correct, contact the
Techline. 2ET082:Motorised throttle
positionNo load
Full load
INTERMEDIATE
3 PR116:Motorised throttle
corrected position
setpointPR116≈ 2%
4 PR111:Motorised throttle
position corrected
valueNo load < 15 %
Full load >30%
5 PR097:Motorised throttle
lower stop
programmed value.5.96% < PR097
< 13.96%
6 PR096:Motorised throttle
upper stop
programmed value80% <PR096 <100%
7 PR429:Measured throttle
position5% < PR096 < 25%
8 PR118:Measured throttle
position gang 1PR118≈ 12%If there is a fault, use
the interpretation for
DF095 Throttle
potentiometer
circuit gang 1.
9 PR119:Measured throttle
position gang 2PR119≈ 12%If there is a fault, use
the interpretation for
DF096 Throttle
potentiometer
circuit gang 2.

PETROL INJECTION
Fault finding - Conformity check
17B
17B-154
PETROL INJECTION
Fault finding - Conformity check
17B
17B-154V9 MR-372-J84-17B050$517.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54
SUB-FUNCTION: DRIVER PARAMETERS (continued 1):
NOTESOnly perform this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine warm, idling.
Order FunctionParameter or Status Checked
or ActionDisplay and notes Fault finding
10Accelerator
pedal and
motorised
throttleET075:Pedal released and
throttle closedYESIf NO, apply the
interpretation of
PR030 Accelerator
pedal position
followed by the
interpretation of fault
ET082 Motorised
throttle valve servo
control.
11
Motorised
throttlePR597:Motorised throttle in
safe mode15% < PR597 < 25%Run command
RZ005
Programming. If the
parameters or
statuses are still not
correct, contact the
Techline. 12 PR593:Motorised throttle in
safe mode gang 1PR593≈ 1 V
13 PR594:Motorised throttle in
safe mode gang 2PR594≈ 1 V
14
Accelerator
pedalET081:Accelerator pedal
positionNo load
Full load
NOT DETECTEDIn the event of a fault
apply the
interpretation for
PR030 Accelerator
pedal position
15 PR030:Accelerator pedal
positionNo load = 0%
Full load = 100%In the event of a fault,
apply interpretation of
DF008 and DF009
Pedal potentiometer
circuit track 1 and
track 2, then DF011
and DF012 Sensor
supply voltage 1 and
2.

PETROL INJECTION
Fault finding - Conformity check
17B
17B-155
PETROL INJECTION
Fault finding - Conformity check
17B
17B-155V9 MR-372-J84-17B050$517.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54
DRIVER PARAMETERS SUB-FUNCTION (continued 2):
NOTESOnly perform this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine warm, idling.
Order FunctionParameter or Status Checked
or ActionDisplay and notes Fault finding
16
Accelerator
pedal
(continued)PR568:Pedal position gang 10.2 V < PR568 < 5 V
Default value: 5 VIn the event of a fault,
apply the
interpretation of fault
DF196 Pedal sensor
circuit gang 1.
17 PR569:Pedal position gang 20.2 V < PR569 < 5 V
Safe value: 0 VIn the event of a fault,
apply the
interpretation of fault
DF198 Pedal sensor
circuit gang 2.
18 PR147:Pedal potentiometer
voltage gang 1PR147≈ 15 VIn the event of a fault,
apply the
interpretation of fault
DF196 Pedal sensor
circuit gang 1.
19 PR148:Pedal potentiometer
voltage gang 2PR148≈ 7.5 VIn the event of a fault,
apply the
interpretation of fault
DF198 Pedal sensor
circuit gang 2.
20 PR424:Programming the
no-load position
valuePR424≈ 15%Run command
RZ005
Programming. If the
parameters are still
not correct, contact
the Techline.

PETROL INJECTION
Fault finding - Conformity check
17B
17B-156
PETROL INJECTION
Fault finding - Conformity check
17B
17B-156V9 MR-372-J84-17B050$517.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54
SUB-FUNCTION: DRIVER PARAMETERS (CONTINUED 3):
NOTESOnly perform this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine warm, idling.
Order FunctionParameter or Status Checked or
ActionDisplay and
notes Fault finding
21
Motorised
throttleAC027:Motorised throttleThe motorised
throttle should
be heard
operatingIn the event of a fault apply
the interpretation of
AC027 Motorised
throttle.
22 PR539:Measured throttle
voltage, gang
circuit 1PR539≈ 2.2 V
In the event of a fault,
apply interpretation of
DF095 Throttle
potentiometer circuit
gang 1 and DF096
Throttle potentiometer
circuit gang 2. 23 PR538:Measured throttle
voltage, gang circuit 2PR538≈ 2.2 V
24 PR587:Motorised throttle
lower stop gang 1PR587≈ 0.5 V
25 PR588:Motorised throttle
lower stop gang 2PR588≈ 0.5 V
26 PR589:Motorised throttle
upper stop gang 1PR589≈ 4.40 V
27 PR590:Motorised throttle
upper stop gang 24.40 VIn the event of a fault,
apply interpretation of
DF095 Throttle
potentiometer circuit
gang 1 and DF096
Throttle potentiometer
circuit gang 2. 28 PR113:Throttle lower stop
after applying. offset10%
29
Motorised
throttleET0565:Type 2 defect modeNO
WITHOUT 30 ET0566:Type 3 defect modeNO
31 ET0567:Type 4 defect modeNO
32 ET0568:Type 5 defect modeNO
33 ET0569:Type 6 defect modeNO

PETROL INJECTION
Fault finding - Conformity check
17B
17B-157
PETROL INJECTION
Fault finding - Conformity check
17B
17B-157V9 MR-372-J84-17B050$517.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54
PREHEATING/IGNITION SUB-FUNCTION:
NOTESOnly perform this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine warm, idling.
Order FunctionParameter or Status Checked
or ActionDisplay and notes Fault finding
1Cylinder
recognitionET061:Cylinder 1
recognitionCOMPLETEDIn the event of a fault,
apply the
interpretation for
status ET061
Cylinder 1
recognition.
2 Engine speed PR055:Engine speedIndicates the
engine's speed of
rotation in rpm.
700 rpm < PR055
< 800 rpmIn the event of a fault,
apply the
interpretation for
DF154 Flywheel
signal sensor
circuit.
3 Flywheel target ET089:Flywheel target
programmingCOMPLETEDSTATUS 1: Flywheel
target fault.
WITHOUT
4 Flywheel ET062:Flywheel signalDETECTEDIn the event of a fault,
apply the
interpretation for
status ET062
Flywheel signal.
5
IgnitionPR448:Ignition advance- 23.6 °V < PR448
<72°V
WITHOUT 6PR095:Anti-pinking
correction0 °V < PR095 < 8 °V
7 PR126:advance after anti-
pinking correction- 23.6 °V < PR126
<72°V
8PR427:Average pinking
signal10,000 < PR427
< 20,000In the event of a fault,
apply the
interpretation of
DF088 Pinking
sensor circuit.

PETROL INJECTION
Fault finding - Conformity check
17B
17B-158
PETROL INJECTION
Fault finding - Conformity check
17B
17B-158V9 MR-372-J84-17B050$517.mif
S3000 Injection
Program No.: AD
Vdiag No.: 4C / 54
IGNITION/PREHEATING SUB-FUNCTION (continued 1):
NOTESOnly perform this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine warm, idling.
Order FunctionParameter or Status Checked
or ActionDisplay and notes Fault finding
9
Combustion
misfireET581:Petrol combustion
misfire fault findingINACTIVE
In the event of a fault,
apply interpretation of
faults DF059
Combustion misfire
in cylinder 1, DF060
Combustion misfire
in cylinder 2, DF061
Combustion misfire
in cylinder 3, DF062
Combustion misfire
in cylinder 4. 10 ET057:Misfiring on
cylinder 1NO
11 ET058:Misfiring on
cylinder 2NO
12 ET059:Misfiring on
cylinder 3NO
13 ET060:Misfiring on
cylinder 4NO
14 Actuators AC079:Actuator static testAll the actuators
must be operated
(fuel pump relay,
electric coolant
pump on F4RT,
downstream and
upstream sensor
heating, motorised
throttle)In the event of a fault,
apply interpretation of
fault associated with
the actuators
concerned.