weight RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16C36 Owner's Manual

13B-427V9 MR-372-J84-13B450$200.mif
DIESEL INJECTION
Fault finding – Tests13B
TEST11
CONTINUED 1
Weigh the diesel fuel and note the fuel weight after subtracting the weight of the empty plastic cup and its cover.
Does the fuel weight fall between the minimum and maximum weights given in the table below?
Calculated weight (g.)
Fuel temperature
(°C)
Min. weight Max. weight
821 846 13
821 846 14
820 845 15
819 844 16
819 844 17
818 843 18
817 842 19
816 841 20
816 841 21
815 840 22
814 839 23
814 839 24
813 838 25
Check the fuel temperature by immersing a thermometer in the plastic cup.
End of test. The fuel is not correct.
If the fuel weight is less than the minimum value then there is petrol in the diesel fuel.
If the fuel weight is greater than the maximum value then there is oil in the diesel fuel.
Drain the fuel circuit, including the tank (see MR 364 (Mégane II ph2), Mechanical,
19C, Tank, Fuel tank: Draining, or MR 370 (Scénic II ph2), Mechanical, 19C,
Tank, Draining the fuel tank).
YESNO
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.

13B-428V9 MR-372-J84-13B450$200.mif
DIESEL INJECTION
Fault finding – Tests13B
TEST11
CONTINUED 2
Note:
If the weight measured reaches the limit values, the measurement can be performed with a 2230 ml plastic cup
(part no.77 11 171 414) and its cover (part no.77 11 171 417):
- Carry out a quick test drive in order to mix the fuel, then remove 2 l of fuel.
- Perform the test again and check the results by multiplying the limit values by 2.
Contact the Techline if you have doubts or problems with the customer.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.

13B-429V9 MR-372-J84-13B450$200.mif
DIESEL INJECTION
Fault finding – Tests13B
TEST12 Manual clearing of weight of soot
Note: In certain cases, this procedure is to be carried out only after replacement of the particle filter or after an
After-sales regeneration of the particle filter.
– Start the engine.
– Raise the engine coolant temperature.
– Read the coolant temperature with the PR064 Coolant temperature until a value greater than 65ºC is obtained.
– Accelerate the engine to 4000 rpm and maintain this speed for 5 minutes.
–After 5 minutes, release the accelerator and stop the engine.
– Switch on the ignition.
– Run command SC036 Reinitialise programming and select After particle filter replacement or After particle
filter regeneration (as appropriate).
– Switch off the ignition and wait for the diagnostic tool message (maximum time 8 minutes): Communication
lost with computer: EDC16C36, check the tool connection and computer power supply.
– Then switch on the ignition again and clear the present or stored faults from the computer memory (operation
to be carried out within 3 minutes of switching on the ignition).
EDC16C36_V44_TEST12/EDC16C36_V4C_TEST12/EDC16C36_V48_TEST12/EDC16C36_V50_TEST12/EDC16C36_V54_TEST12/
EDC16C36_V58_TEST12EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.