check oil RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals Siemens Injection Owner's Manual

13B-309
MR-372-J84-13B050$936.mif
V17
DIESEL INJECTION
Fault finding – Tests13B
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
TEST 5
CONTINUED 1
Reconnect the fuel flow solenoid valve
connector; before restarting the engine, switch
off the ignition and wait 30 seconds.
Remove the connector for the fuel pressure
solenoid valve (white), does the engine stop?
YES
Reconnect the connector of the fuel pressure
solenoid valve, switch off the ignition and wait for
30 seconds.
Check that the oil level is correct and that the
engine coolant temperature is greater than 60°C.
Engine running at idle speed.
– Run command AC029 High pressure circuit
sealing test.
The engine will perform 4acceleration cycles.
– Refer to parameters PR008 Rail pressure
setpoint and PR038 Rail pressure.
–Does PR038 Rail pressure follow PR008 Rail
pressure setpoint during the phase of the
4acceleration cycles?
NO
NOReplace the pump (the fuel pressure
solenoid valve remains closed
mechanically).
YESCheck the injectors by carrying out Te s t 6.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
A
B

13B-323
MR-372-J84-13B050$936.mif
V17
DIESEL INJECTION
Fault finding – Tests
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
TEST 9
CONTINUED 2
PA R T B
1 - NO particle filter regeneration.
2 - Write on the repair order: the parameter and status relating to the last failure:
– Mileage of last Particle filter warning light record
– Mileage of last Failed regeneration records
– Engine statuses for last Engine status records
Example: PR837 = 2794 miles (4657 km); PR801 = 2760 miles (4600 km); engine status = STOPPED
3 - Interpretation of the values written on the repair order by the service advisor for the customer:
Before the last time the warning light or Particle Filter message came on (appeared at the mileage of the last
Stored particle filter warning light) the customer did not follow the driving instructions: the failure which
occurred at the Mileage of the last failure was due to the engine being switched off.
4 - Service advisor explains to the customer the procedure to turn off the warning light, backed up by the
parameters written in the repair order: see PA R T D.
PA R T C
1 - Carry out a regeneration in the Renault dealership with the approval of the Techline.
Follow the procedure for command SC017 Particle filter regeneration.
Note: Do not carry out an engine oil change following an After-Sales regeneration.
2 - Explain the procedure for regeneration while driving to the customer to reduce returns to the garage:
see SECTION D:
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.

13B-324
MR-372-J84-13B050$936.mif
V17
DIESEL INJECTION
Fault finding – Tests
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
TEST 9
CONTINUED 3
SECTION D - Procedure for switching off the particle filter message or warning light on the instrument panel
Certain types of driving can trigger the activation of the particle filter warning light or message. This fault occurs
when the weight of soot is more than 30.8 g.
The customer must carry out a specific driving operation (cf. vehicle user manual) that consists of:
1. Making sure the engine is warm
2. Drive at a speed greater than 24 mph (40 km/h) for 2 minutes to initiate the regeneration process.
Initiating regeneration Minimum speed Minimum time
All vehicle types 24 mph (40 km/h) 2 minutes
3. Then drive at a speed of more than 24 mph (40 km/h) until the Particle Filter message or warning light on the
instrument panel goes out. In order for the procedure to succeed, it is necessary to drive without stopping
(without stopping the engine) or to leave the engine running at idle speed for an extended period of time. The
regeneration time depends on the vehicle and driving conditions but normally lasts about 20 minutes.
Regeneration duration Minimum speed Average time
All vehicle types 24 mph (40 km/h) 20 minutes
4. If regeneration when driving fails (the warning light has not switched off or the service warning light has come
on), carry out a particle filter regeneration in the Renault dealership. To carry out After-Sales regeneration:
check the oil level and remove some oil if the maximum level has been reached, then apply the procedure for
command SC017 Particle filter regeneration (see Interpretation of commands).
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.

13B-328
MR-372-J84-13B050$975.mif
V17
DIESEL INJECTION
Fault finding – Tests13B
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
TEST 13
CONTINUED 1
Weigh the diesel fuel and note the fuel weight after subtracting the weight of the empty plastic cup and its cover.
Does the fuel weight fall between the minimum and maximum weights given in the table below?
Calculated weight (g.)
Fuel temperature
(ºC)
Min. weight Max. weight
821 846 13
821 846 14
820 845 15
819 844 16
819 844 17
818 843 18
817 842 19
816 841 20
816 841 21
815 840 22
814 839 23
814 839 24
813 838 25
Check the fuel temperature by immersing a thermometer in the plastic cup.
End of test.The fuel is not correct.
If the fuel weight is less than the minimum value then there is
petrol in the diesel fuel.
If the fuel weight is greater than the maximum value then there is
oil in the diesel fuel.
Drain the fuel circuit, including the tank (see MR 392 (Clio III),
364 (Mégane II ph2), and 417 (Kangoo II), Mechanical, 19C,
Tank, Fuel tank: Draining or MR 385 (Modus) and 370 (Scénic II
ph2), Mechanical, 19C, Tank, Draining the fuel tank
).
A
YESNO
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.