oil RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals Workshop Manual

13B-7V4 MR-372-J84-13B000$010.mif
DIESEL INJECTION
Fault finding – Introduction13B
DDCR INJECTION
Vdiag No.: 44, 48
Advice to be followed before any operation
Protect the accessories and timing belts, the electrical accessories (starter, alternator, electric power assisted
steering pump) and the mating face to prevent diesel fuel spilling onto the clutch friction plate).
Check that you have plugs for the unions to be opened (set of plugs available from the Parts Department). The plugs
are single-use only. After use, they must be discarded (once used they are soiled and cleaning is not sufficient to
make them reusable). Unused plugs must be discarded.
Ensure that you have hermetically resealable plastic bags for storing removed parts. Parts stored in this way will be
less susceptible to the risk of contamination. These are single-use bags; after use they must be discarded.
Use lint-free cleaning cloths (part no. 77 11 211 707). Using normal cloth or paper is prohibited. They are not lint-free
and could contaminate the fuel circuit. Each cloth should only be used once.
Use fresh cleaning agent for each operation (used cleaning agent is contaminated). Pour it into an uncontaminated
container.
For each operation, use a clean brush in good condition (the brush must not shed its bristles).
Use a brush and cleaning agent to clean the unions to be opened.
Blow compressed air over the cleaned parts (the tools and workbench, as well as the parts, unions, and injection
system sections). Check that no bristles remain.
Wash your hands before and during the operation if necessary.
When wearing leather protective gloves cover them with latex gloves to prevent contamination.
Instructions to be followed during the operation
As soon as the circuit is open, all openings must be plugged to prevent impurities from entering the system.
The plugs to be used are available from the Parts Department. They must not be reused under any circumstances.
Close the hermetically sealed bag, even if it has to be reopened shortly afterwards. Ambient air carries impurities.
All components removed from the injection system must be stored in a hermetically sealed plastic bag once they
have been plugged.
Using a brush, cleaning agent, air gun, sponge or normal cloth is strictly prohibited once the circuit has been
opened. These items are likely to allow impurities to enter the system.
A new component replacing an old one must not be removed from its packaging until it is to be fitted to the vehicle.

13B-163V4 MR-372-J84-13B000$120.mif
DIESEL INJECTION
Fault finding – Tests13B
DDCR INJECTION
Vdiag No.: 44, 48
TEST 13
CONTINUED 1
Weigh the diesel fuel and note the fuel weight after subtracting the weight of the empty plastic cup and its cover.
Does the fuel weight fall between the minimum and maximum weights given in the table below?
Calculated weight (g.)
Fuel temperature
(°C)
Min. weight Max. weight
821 846 13
821 846 14
820 845 15
819 844 16
819 844 17
818 843 18
817 842 19
816 841 20
816 841 21
815 840 22
814 839 23
814 839 24
813 838 25
Check the fuel temperature by immersing a thermometer in the plastic cup.
End of test. The fuel is not correct.
If the fuel weight is less than the minimum value then there is petrol in the diesel
fuel.
If the fuel weight is greater than the minimum value then there is oil in the diesel
fuel.
Drain the fuel circuit, including the tank (see MR 364 (Mégane) or 370 (Scénic),
Mechanical, 19C, Tank, Fuel Tank: Draining).
A
NO
YESNO

13B-165V4 MR-372-J84-13B000$130.mif
13B
DDCR INJECTION
Vdiag No.: 44, 48
NOTESSpecial note:
Only consult this customer complaint after a complete check with the diagnostic
tool.
No dialogue with the computer ALP1
Starting fault:
The engine will not startALP2
The engine starts with difficulty, or starts then stalls ALP3
Starting difficult with warm engine ALP4
Rough idle (pumping)ALP5
Idling speed too high or too low ALP6
Behaviour while driving:
Erratic acceleration/deceleration and engine racing ALP7
Acceleration gapALP8
Engine cut-out (stalling)ALP9
Engine buckingALP10
Loss of powerALP11
Too much powerALP12
Excessive consumptionALP13
Overspeed when releasing accelerator or changing gear ALP14
Engine dies on pulling awayALP15
Noise, odours or smoke:
Engine rattling, noisy engine, turbocharger noise ALP16
Blue, white or black smokeALP17
Oil leaks from the turbocharger ALP18
DIESEL INJECTION
Fault finding – Customer complaints

13B-167
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V4 MR-372-J84-13B000$140.mif
DIESEL INJECTION
Fault finding – Fault finding charts13B
InjectionDDCR
Vdiag No.: 44, 48
ALP2 The engine will not start
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
Check that the fuel tank is correctly filled and that the fuel is correct: run TEST 13 Diesel fuel conformity check.
Check the levels of engine oil and coolant.
Check the air inlet circuit by running TEST 5 Inlet circuit check.
Is the catalytic converter clogged or damaged?Replace the catalytic converter (see MR
364 (Mégane II) or MR 370 (Scénic II),
Mechanical, 19B, Exhaust, Catalytic
converter: Removal - Refitting).
Check the air inlet circuit by running TEST 2 Electrical circuit check.
Check the electrical conformity of the heater plugs (the resistance value of the heater plug must be less than 2 Ω).
Is the timing set correctly? Carry out the necessary repairs.
Visually check the condition of the engine wiring harness.
YES
NO
NO
YES
A
DDCR_V44_ALP02/DDCR_V48_ALP02

13B-170
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V4 MR-372-J84-13B000$140.mif
DIESEL INJECTION
Fault finding – Fault finding charts13B
InjectionDDCR
Vdiag No.: 44, 48
ALP3 The engine starts with difficulty, or starts then stalls
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
Check that the fuel tank is correctly filled and that the fuel is correct by running TEST 13 Diesel fuel conformity
check.
Check the levels of engine oil and coolant.
Check the air inlet circuit: run test 5 Air inlet circuit check.
Is the catalytic converter clogged or damaged?Replace the catalytic converter (see MR 364
(Mégane II) or MR 370 (Scénic II),
Mechanical, 19B, Exhaust, Catalytic
converter: Removal - Refitting).
Check the electrical conformity of the heater plugs (the resistance value of the heater plug must be less than 2 Ω).
Is the timing set correctly? Carry out the necessary repairs.
Is the compression in order? Carry out the necessary repairs.
YES
NO
NO
YES
NO
YES
A
DDCR_V44_ALP03/DDCR_V48_ALP03

13B-176
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V4 MR-372-J84-13B000$140.mif
DIESEL INJECTION
Fault finding – Fault finding charts13B
InjectionDDCR
Vdiag No.: 44, 48
ALP7 Unexpected acceleration/deceleration and engine racing
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
Check that the engine has not sucked up its oil (engine racing).
Check the air inlet circuit by running TEST 5 Inlet circuit check.
Using the diagnostic tool, check that the injector codes (C2I) are correctly entered on the identification screen. If
not, configure the correct injector codes using command SC002 Enter injector codes.
Visually check the condition of the engine wiring harness.
Check the injectors by running TEST 3 Injector check.
Check that the computer connectors are properly locked.
Check the condition of the computer connections (bent pin, signs of corrosion, silicone, etc.).
If the connector(s) are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Contact the Techline if the customer complaint is still present.
DDCR_V44_ALP07/DDCR_V48_ALP07

13B-179
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V4 MR-372-J84-13B000$140.mif
DIESEL INJECTION
Fault finding – Fault finding charts13B
InjectionDDCR
Vdiag No.: 44, 48
ALP9 Engine cut-out (stalling)
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
Check that the fuel tank is correctly filled and that the fuel is correct by running TEST 13 Diesel fuel conformity
check.
Check the levels of engine oil and coolant.
Check that the engine has not sucked up its oil (engine racing).
Check the air inlet circuit by running TEST 5 Inlet circuit check.
Is the catalytic converter clogged or
damaged?Replace the catalytic converter (see MR 364
(Mégane II) or MR 370 (Scénic II), Mechanical, 19B,
Exhaust, Catalytic converter: Removal - Refitting).
Visually check the condition of the engine wiring harness.
Check the air inlet circuit by running TEST 2 Electrical circuit check.
Check the low pressure circuit by running TEST 1 Low pressure circuit check.
YES
NO
A
DDCR_V44_ALP09/DDCR_V48_ALP09

13B-183
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V4 MR-372-J84-13B000$140.mif
DIESEL INJECTION
Fault finding – Fault finding charts13B
InjectionDDCR
Vdiag No.: 44, 48
OCR*: opening cyclic ratio
ALP11 Loss of power
NOTESSpecial note:
Only consult this customer complaint after a full check with the diagnostic tool.
See explanation for flow capacity function in system operation.
In this case, the lack of power is due to insufficient vacuum for the OCR * setpoint given.
Is the "Flow capacity function" programming
active (ET563)?Check the diesel filter.
Is it close to the replacement mileage?
Using the diagnostic tool, check that the injector
codes (C2I) are correctly entered on the identification
screen. If not, configure the correct injector codes
using command SC002 Enter injector codes.Replace the diesel filter (see MR 364
(Mégane II) or MR 370 (Scénic II),
Mechanical, 13A, Fuel supply, Fuel filter:
Removal - Refitting).
Check the air inlet circuit by running TEST 5 Inlet
circuit check.
Is the engine oil level correct? Top up the oil level.
Is the catalytic converter clogged or damaged?Replace the catalytic converter (see MR
364 (Mégane II) or MR 370 (Scénic II),
19B, Exhaust, Catalytic converter:
Removal - Refitting).
YES
NO
NO
YES
NO
YES
YES
A
NO
DDCR_V44_ALP11/DDCR_V48_ALP11

13B-185
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V4 MR-372-J84-13B000$140.mif
DIESEL INJECTION
Fault finding – Fault finding charts13B
InjectionDDCR
Vdiag No.: 44, 48
ALP12 Too much power
NOTESOnly consult this customer complaint after a full check with the diagnostic tool.
Using the diagnostic tool, check that the injector codes (C2I) are correctly entered on the identification screen. If
not, configure the correct injector codes using command SC002 Enter injector codes.
Check the air inlet circuit by running TEST 5 Inlet circuit check.
Check that the engine has not sucked up its oil (engine racing).
Check the injectors: run TEST 3 Injector check.
Check that the computer connectors are properly locked.
Check the condition of the computer connections (bent pin, signs of corrosion, silicone, etc.).
If the connector(s) are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Contact the Techline if the customer complaint is still present.
DDCR_V44_ALP12/DDCR_V48_ALP12

13B-186
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V4 MR-372-J84-13B000$140.mif
DIESEL INJECTION
Fault finding – Fault finding charts13B
InjectionDDCR
Vdiag No.: 44, 48
ALP 13 Excessive consumption
NOTESOnly consult this customer complaint after a full check with the diagnostic tool.
Check that the fuel tank is correctly filled and that the fuel is correct by running TEST 13 Diesel fuel conformity
check.
Check the levels of engine oil and coolant.
Is the fuel temperature sensor leaking?Replace the fuel temperature sensor
(see MR 364 (Mégane II) or MR 370
(Scénic II), Mechanical, 13B, Diesel
injection, Rail pressure sensor:
Removal - Refitting).
Check the low pressure circuit by running TEST 1 Low pressure circuit check.
Check the injectors by running TEST 3 Injector check.
Visually check that there are no leaks on the high pressure circuit by running TEST 7 High pressure circuit
sealing check.
Check the air inlet circuit by running TEST 5 Inlet circuit check.
YES
NO
A
DDCR_V44_ALP13/DDCR_V48_ALP13