engine coolant RENAULT SCENIC 2012 J95 / 3.G Engine And Peripherals EDC16CP33 Owners Manual

13B-369
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR089VEHICLE SPEED
PARAMETER
DEFINITIONGives the vehicle speed in km/h.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
This parameter is transmitted by the ABS computer. This signal is transmitted to the
injection on the multiplex network.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
In the event of a fault, test the multiplex network (see 88B, Multiplex).
And then complete fault finding on the ABS computer (see 38C, Anti-lock braking system).
EDC16CP33_V18_PR089 / EDC16CP33_V1C_PR089 / EDC16CP33_V54_PR089 / EDC16CP33_V20_PR089 / EDC16CP33_V58_PR089 /
EDC16CP33_V5C_PR089 / EDC16CP33_V24_PR089 / EDC16CP33_V04_PR089 / EDC16CP33_V08_PR089 / EDC16CP33_V44_PR089 /
EDC16CP33_V4C_PR089 / EDC16CP33_V34_PR089 / EDC16CP33_V38_PR089 / EDC16CP33_V74_PR089 / EDC16CP33_V28_PR089 /
EDC16CP33_V62_PR089 / EDC16CP33_V26_PR089 / EDC16CP33_V60_PR089
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-370
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
OCR*: Opening Cyclic Ratio
SV*: Solenoid valve
PR104TURBOCHARGING SV* OCR* SETPOINT
PARAMETER
DEFINITIONThis parameter indicates the turbocharging solenoid valve opening ratio percentage.
NOTESNone.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
PR104 ≈ PR846 TURBOCHARGING SOLENOID VALVE OCR, these 2 values must be similar.
In the event of a fault, consult the interpretation of fault DF054 EGR valve position sensor circuit.
EDC16CP33_V18_PR104 / EDC16CP33_V1C_PR104 / EDC16CP33_V54_PR104 / EDC16CP33_V20_PR104 / EDC16CP33_V58_PR104 /
EDC16CP33_V5C_PR104 / EDC16CP33_V24_PR104 / EDC16CP33_V04_PR104 / EDC16CP33_V08_PR104 / EDC16CP33_V44_PR104 /
EDC16CP33_V4C_PR104 / EDC16CP33_V34_PR104 / EDC16CP33_V38_PR104 / EDC16CP33_V74_PR104 / EDC16CP33_V28_PR104 /
EDC16CP33_V62_PR104 / EDC16CP33_V26_PR104 / EDC16CP33_V60_PR104
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-371
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR128FIRST EGR VALVE OFFSET
PARAMETER
DEFINITIONThis parameter indicates the closing ratio of the EGR valve for the first offset of
the EGR valve.
NOTESNone.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
The EGR valve closure value during the first EGR valve offset must be between:
15% < PR128 < 25%.
PR128 ≈ PR129 Last EGR valve offset, these 2 values should be similar.
In the event of a fault, see the interpretation of faults DF209 EGR valve position sensor circuit and DF647 EGR
valve position regulation.
EDC16CP33_V18_PR128 / EDC16CP33_V1C_PR128 / EDC16CP33_V54_PR128 / EDC16CP33_V20_PR128 / EDC16CP33_V58_PR128 /
EDC16CP33_V5C_PR128 / EDC16CP33_V24_PR128 / EDC16CP33_V04_PR128 / EDC16CP33_V08_PR128 / EDC16CP33_V44_PR128 /
EDC16CP33_V4C_PR128 / EDC16CP33_V34_PR128 / EDC16CP33_V38_PR128 / EDC16CP33_V74_PR128 / EDC16CP33_V28_PR128 /
EDC16CP33_V62_PR128 / EDC16CP33_V26_PR128 / EDC16CP33_V60_PR128
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-372
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR129LAST EGR VALVE OFFSET
PARAMETER
DEFINITIONThis parameter indicates the closing ratio of the EGR valve for the first EGR valve offset.
NOTESNone.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
The EGR valve closure value during the last EGR valve offset must be between:
15% < PR129 < 25%.
PR128 First EGR valve offset ≈ PR129, these 2 values should be similar.
In the event of a fault, consult the interpretation of faults DF209 EGR valve position sensor circuit and DF647
EGR valve position regulation.
EDC16CP33_V18_PR129 / EDC16CP33_V1C_PR129 / EDC16CP33_V54_PR129 / EDC16CP33_V20_PR129 / EDC16CP33_V58_PR129 /
EDC16CP33_V5C_PR129 / EDC16CP33_V24_PR129 / EDC16CP33_V04_PR129 / EDC16CP33_V08_PR129 / EDC16CP33_V44_PR129 /
EDC16CP33_V4C_PR129 / EDC16CP33_V34_PR129 / EDC16CP33_V38_PR129 / EDC16CP33_V74_PR129 / EDC16CP33_V28_PR129 /
EDC16CP33_V62_PR129 / EDC16CP33_V26_PR129 / EDC16CP33_V60_PR129
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-373V12 MR-372-J84-13B300$122.mif
13B
PR130CRUISE CONTROL SETPOINT
PARAMETER
DEFINITIONThis parameter indicates the cruise control speed setpoint in mph (km/h).
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
There must be no faults present.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– or after a customer complaint (lack of power, smoke etc.).
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
The cruise control speed setpoint closure value must be:
PR130 > 18 mph (30 km/h).
Cruise control can only be activated for a speed.
EDC16CP33_V18_PR130 / EDC16CP33_V1C_PR130 / EDC16CP33_V54_PR130 / EDC16CP33_V20_PR130 / EDC16CP33_V58_PR130 /
EDC16CP33_V5C_PR130 / EDC16CP33_V24_PR130 / EDC16CP33_V04_PR130 / EDC16CP33_V08_PR130 / EDC16CP33_V44_PR130 /
EDC16CP33_V4C_PR130 / EDC16CP33_V34_PR130 / EDC16CP33_V38_PR130 / EDC16CP33_V74_PR130 / EDC16CP33_V28_PR130 /
EDC16CP33_V62_PR130 / EDC16CP33_V26_PR130 / EDC16CP33_V60_PR130
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-374V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR132AIR FLOW
PARAMETER
DEFINITIONThis parameter indicates the inlet air flow in kg/h.
NOTESThere must be no faults present.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– or after a customer complaint (lack of power, smoke etc.).
Use the Technical Note Wiring Diagram, Laguna II ph2, Vel Satis ph2, Mégane ll
ph2, Scénic ll ph2, Espace IV ph2.
Conformity check with engine stopped and ignition on.
The inlet air flow value must be:
PR132 = 0 kg/h.
Conformity check with the engine running and engine coolant temperature > 80°C
The inlet air flow value must be between:
20 kg/h < PR132 < 30 kg/h.
EDC16CP33_V18_PR132 / EDC16CP33_V1C_PR132 / EDC16CP33_V54_PR132 / EDC16CP33_V20_PR132 / EDC16CP33_V58_PR132 /
EDC16CP33_V5C_PR132 / EDC16CP33_V24_PR132 / EDC16CP33_V04_PR132 / EDC16CP33_V08_PR132 / EDC16CP33_V44_PR132 /
EDC16CP33_V4C_PR132 / EDC16CP33_V34_PR132 / EDC16CP33_V38_PR132 / EDC16CP33_V74_PR132 / EDC16CP33_V28_PR132 /
EDC16CP33_V62_PR132 / EDC16CP33_V26_PR132 / EDC16CP33_V60_PR132
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-376V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR157FUEL FLOW SETPOINT
PARAMETER
DEFINITIONThis parameter indicates the fuel flow setpoint in mg/st.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check: Engine stopped and ignition on
The fuel flow setpoint value must be:
PR157 = 0 mg/st (ignition on).
In the event of a fault, consult the interpretation of DF897 Pump pressure regulator circuit.
Conformity check with the engine running and engine coolant temperature > 80°C
Engine running: PR017: Fuel flow = PR157.
In the event of a fault, refer to the interpretation of fault DF897.
EDC16CP33_V18_PR157 / EDC16CP33_V1C_PR157 / EDC16CP33_V54_PR157 / EDC16CP33_V20_PR157 / EDC16CP33_V58_PR157 /
EDC16CP33_V5C_PR157 / EDC16CP33_V24_PR157 / EDC16CP33_V04_PR157 / EDC16CP33_V08_PR157 / EDC16CP33_V44_PR157 /
EDC16CP33_V4C_PR157 / EDC16CP33_V34_PR157 / EDC16CP33_V38_PR157 / EDC16CP33_V74_PR157 / EDC16CP33_V28_PR157 /
EDC16CP33_V62_PR157 / EDC16CP33_V26_PR157 / EDC16CP33_V60_PR157
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-377V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR171AIR FLOW SETPOINT FOR EGR
PARAMETER
DEFINITIONThis parameter indicates the fuel flow setpoint in mg/st.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
Indicates the air flow required by the EGR valve
EDC16CP33_V18_PR171 / EDC16CP33_V1C_PR171 / EDC16CP33_V54_PR171 / EDC16CP33_V20_PR171 / EDC16CP33_V58_PR171 /
EDC16CP33_V5C_PR171 / EDC16CP33_V24_PR171 / EDC16CP33_V04_PR171 / EDC16CP33_V08_PR171 / EDC16CP33_V44_PR171 /
EDC16CP33_V4C_PR171 / EDC16CP33_V34_PR171 / EDC16CP33_V38_PR171 / EDC16CP33_V74_PR171 / EDC16CP33_V28_PR171 /
EDC16CP33_V62_PR171 / EDC16CP33_V26_PR171 / EDC16CP33_V60_PR171
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-378V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR190IDLE SPEED SETPOINT
PARAMETER
DEFINITIONThis parameter indicates the engine's rotational speed in rpm.
NOTESNone.
Conformity check with engine stopped and ignition on.
With the ignition on, the engine speed value must be:
PR190 = 800 rpm or PR190 = 850 rpm (depending on the vehicle).
In the event of a fault, refer to the interpretation of faults DF195 Camshaft sensor / engine speed consistency,
DF119 Camshaft sensor signal and DF120 Engine speed sensor signal.
Conformity check with the engine running and engine coolant temperature > 80°C
With the engine running at idle speed, the engine speed value must be:
PR190 = 800 rpm or PR190 = 850 rpm (depending on the vehicle).
In the event of a fault, refer to the interpretation of faults DF195, DF119 and DF120.
The difference between the engine idle speed and its setpoint must be less than 50 rpm.
EDC16CP33_V18_PR190 / EDC16CP33_V1C_PR190 / EDC16CP33_V54_PR190 / EDC16CP33_V20_PR190 / EDC16CP33_V58_PR190 /
EDC16CP33_V5C_PR190 / EDC16CP33_V24_PR190 / EDC16CP33_V04_PR190 / EDC16CP33_V08_PR190 / EDC16CP33_V44_PR190 /
EDC16CP33_V4C_PR190 / EDC16CP33_V34_PR190 / EDC16CP33_V38_PR190 / EDC16CP33_V74_PR190 / EDC16CP33_V28_PR190 /
EDC16CP33_V62_PR190 / EDC16CP33_V26_PR190 / EDC16CP33_V60_PR190
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-379V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR209TURBOCHARGING PRESSURE LOOP DIFFERENCE
PARAMETER
DEFINITIONThis parameter indicates the turbocharging pressure loop difference in bar.
NOTESNone.
Conformity check: Engine running, engine coolant temperature > 80°C, without electrical consumers.
The turbocharging pressure loop difference value must be:
PR209 = PR009 Turbocharging pressure setpoint - PR041 Turbocharging pressure = ~ 0.
If PR209 is significant, refer to the interpretation of the command AC004 Turbocharging solenoid valve.
EDC16CP33_V18_PR209 / EDC16CP33_V1C_PR209 / EDC16CP33_V54_PR209 / EDC16CP33_V20_PR209 / EDC16CP33_V58_PR209 /
EDC16CP33_V5C_PR209 / EDC16CP33_V24_PR209 / EDC16CP33_V04_PR209 / EDC16CP33_V08_PR209 / EDC16CP33_V44_PR209 /
EDC16CP33_V4C_PR209 / EDC16CP33_V34_PR209 / EDC16CP33_V38_PR209 / EDC16CP33_V74_PR209 / EDC16CP33_V28_PR209 /
EDC16CP33_V62_PR209 / EDC16CP33_V26_PR209 / EDC16CP33_V60_PR209
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.