ET051 RENAULT SCENIC 2014 J95 / 3.G Petrol Injection - Sagem3000 Workshop Manual

PETROL INJECTION
Fault finding – Configurations and programming17B
17B - 16V12 MR-372-J84-17B000$225.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48PETROL INJECTION
Fault finding – Configurations and programming
1. CONFIGURATION
Computer configuration by automatic detection
The computer can automatically configure itself based on the sensors or vehicle options it detects.
2. PROGRAMMING
Programming the flywheel target
Accelerate up to 4000 rpm in 3rd gear then decelerate to power take-up* speed. Then repeat immediately.
Check the programming with ET089.
Programming the throttle end stops
After replacing the computer or motorised throttle valve, after switching on the ignition, wait 30 seconds for the
computer to memorise the MAXIMUM and MINIMUM stops.
Check the programming with ET051.
* This is the moment when, during deceleration with no load, the engine drops to idle speed and recovers torque.
JSAA741.0
MR-372-J84-17B000$225.mif

PETROL INJECTION
Fault finding – Conformity check17B
17B-97V12 MR-372-J84-17B000$450.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
DRIVER PARAMETERS SUB-FUNCTION
NOTESOnly check conformity after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
Order FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
1
Motorised
throttleET085: Motorised throttle
in defect modeNO
STATUS 0
STATUS 1
STATUS 2
STATUS 3
STATUS 4
STATUS 5WITHOUT
2 ET051: Throttle stop
programmingCOMPLETED
Run command RZ005
Programming. If the parameters
and statuses are still incorrect,
contact the Techline. 3 PR097: Motorised throttle
lower stop
programmed
value.5.96% < PR097
< 13.96%
4 PR113: Throttle lower stop
after applying
Offset5.96% < PR113
< 13.96%
5 PR096: Motorised throttle
upper stop
programmed valuePR096 = 87.99%
6 ET082: Motorised throttle
positionOPEN
CLOSED
NOT DETECTEDIf NOT DETECTED, apply
interpretation of ET082 Motorised
throttle valve position.
7 PR118: Motorised throttle
position gang 1No load = 4%
Full load = 99.02%If there is a fault, use the
interpretation for DF095 Throttle
potentiometer circuit gang 1.
8 PR119: Motorised throttle
position gang 2No load = 4%
Full load = 100%If there is a fault, use the
interpretation for DF096 Throttle
potentiometer circuit gang 2.
9 PR116: Motorised throttle
corrected position
setpointNo load = 0%
Full load = 60%
WITHOUT
10 PR111: Motorised throttle
position corrected
value.No load = 0%
Full load = 60%
JSAA741.0

PETROL INJECTION
Fault finding – Conformity check17B
17B-118V12 MR-372-J84-17B000$450.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
DRIVER PARAMETERS SUB-FUNCTION
NOTESOnly check conformity after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine warm, at idle speed.
Order FunctionParameter or Status
Checked or ActionDisplay and
notes Fault finding
1
Motorised
throttleET085: Motorised throttle in
defect modeNO
STATUS 0
STATUS 1
STATUS 2
STATUS 3
STATUS 4
STATUS 5WITHOUT
2ET051: Throttle stop
programmingCOMPLETED
Run command RZ005
Programming. If the
parameters and statuses are
still incorrect, contact the
Techline. 3 PR097: Motorised throttle
lower stop
programmed value.5.96% < PR097
< 13.96%
4 PR113:Throttle lower stop
after applying offset5.96% < PR113
< 13.96%
5 PR096: Motorised throttle
upper stop
programmed valuePR096 = 87.99%
6ET082: Motorised throttle
positionOPEN
CLOSED
NOT DETECTEDIf NOT DETECTED, apply
interpretation of ET082
Motorised throttle valve
position.
7 PR118: Motorised throttle
position gang 1No load = 4%
Full load =
99.02%If there is a fault, use the
interpretation for DF095
Throttle potentiometer
circuit gang 1.
8 PR119: Motorised throttle
position gang 2No load = 4%
Full load = 100%If there is a fault, use the
interpretation for DF096
Throttle potentiometer
circuit gang 2.
9 PR116: Motorised throttle
corrected position
setpointNo load = 0%
Full load = 83%
WITHOUT
10 PR111: Motorised throttle
position corrected
value.No load = 0%
Full load = 83%
JSAA741.0

PETROL INJECTION
Fault finding – Status summary table17B
17B - 132V12 MR-372-J84-17B000$540.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48PETROL INJECTION
Fault finding – Status summary table
Tool Status Diagnostic tool title
ET001+ After ignition computer feed
ET003Engine immobiliser
ET004Air conditioning authorisation
ET006Code programmed
ET014Fan unit 1 check
ET015Fan unit 2 check
ET023Fast idle speed request
ET042Cruise control/speed limiter
ET047Fuel pump control circuit
ET048Actuator relay control
ET050Canister bleed control
ET051Throttle stop programming
ET052Upstream O
2 sensor heating
ET053Downstream O
2 sensor heating
ET054Idle speed regulation
ET055Upstream sensor richness loop.
ET057Misfiring on cylinder 1
ET058Misfiring on cylinder 2
ET059Misfiring on cylinder 3
ET060Misfiring on cylinder 4
ET062Flywheel signal
ET063Park/Neutral position
ET064Level 1 injection fault
ET065Level 2 Injection fault
ET066LPG Fault
ET067LPG Ready
ET068LPG tank empty
ET069Operation in LPG mode
ET070Operation in petrol mode
ET071Transition from petrol mode to LPG mode
ET072Transition from LPG mode to petrol mode
ET073Condition for switching to LPG mode
JSAA741.0
MR-372-J84-17B000$540.mif