buttons RENAULT SCENIC 2014 J95 / 3.G Petrol Injection - Sagem3000 Workshop Manual

PETROL INJECTION
Fault finding – Conformity check17B
17B-105V12 MR-372-J84-17B000$450.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
CRUISE CONTROL/SPEED LIMITER SUB-FUNCTION
NOTESOnly check conformity after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
Order FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
1
Cruise
control/
Speed
limiterET042: Cruise control/
speed limiter.- NOT DETECTED: Vehicle
not equipped with cruise
control/speed limiter function
buttons or after reprogramming
or programming the injection
computer, the switch is in the
rest position.
– INACTIVE: When no buttons
are pressed.
- SPEED LIMITER: Main
switch in speed limiter position.
- CRUISE CONTROL: Main
switch in cruise control
position.In the event of a fault,
apply the interpretation
of status ET042 Cruise
control/Speed limiter.
2 ET703: Cruise control/
speed limiter
buttons- INACTIVE: No cruise control/
speed limiter button is pressed.
- PLUS: When the cruise
control/speed limiter "+" button
is pressed.
- MINUS: When the cruise
control/speed limiter "-" button
is pressed.
- SUSPEND: When the cruise
control/speed limiter "0" button
is pressed.
- RESUME: When the cruise
control/speed limiter "R" button
is pressed.In the event of a fault,
consult the
interpretation of status
ET703 Cruise control/
speed limiter button.
JSAA741.0

PETROL INJECTION
Fault finding – Conformity check17B
17B - 126V12 MR-372-J84-17B000$495.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
CRUISE CONTROL/SPEED LIMITER SUB-FUNCTION
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine warm, idling.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1
Cruise
control/
Speed
limiterET042: Cruise control/
speed limiter.- NOT DETECTED: Vehicle
not equipped with cruise
control/speed limiter function
buttons or after reprogramming
or programming the injection
computer, the switch is in the
rest position.
– INACTIVE: When no buttons
are pressed.
- SPEED LIMITER: Main
switch in speed limiter position.
- CRUISE CONTROL: Main
switch in cruise control
position.In the event of a fault,
apply the interpretation
of status ET042 Cruise
control/Speed limiter.
2 ET703: Cruise control/
speed limiter
buttons- INACTIVE: No cruise control/
speed limiter button is pressed.
- PLUS: When the cruise
control/speed limiter “+” button
is pressed.
- MINUS: When the cruise
control/speed limiter
“-” button is pressed.
- SUSPEND: When the cruise
control/speed limiter “0” button
is pressed.
- RESUME: When the cruise
control/speed limiter “R” button
is pressed.In the event of a fault,
consult the
interpretation of status
ET703 Cruise control/
speed limiter button.
JSAA741.0

PETROL INJECTION
Fault finding – Status summary table17B
17B - 133V12 MR-372-J84-17B000$540.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
*AT: automatic transmission
*RCH: passenger compartment heating resistorTool Status Diagnostic tool title
ET074OBD warning light lit by AT*
ET075Pedal released and throttle closed
ET076Starting
ET077Impact detected
ET079Air conditioning present
ET081Accelerator pedal position
ET082Motorised throttle position
ET083Camshaft dephaser in defect mode
ET084Camshaft dephaser
ET086Camshaft dephaser control
ET088Compressor actuation request
ET089Flywheel target programming
ET111RCH* number set
ET112RCH* cut-off
ET405Clutch pedal switch
ET415Deactivation of cruise control/speed limiter
ET542Oil vapour defreeze resistor
ET543Coolant pump control
ET564Type 1 defect mode
ET565Type 2 defect mode
ET566Type 3 defect mode
ET567Type 4 defect mode
ET568Type 5 defect mode
ET569Type 6 defect mode
ET582LPG combustion misfire fault finding
ET703Cruise control/speed limiter buttons
ET704Brake switch No. 1
ET705Brake switch No. 2
JSAA741.0

PETROL INJECTION
Fault finding – Interpretation of statuses17B
17B - 134V12 MR-372-J84-17B000$540.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48PETROL INJECTION
Fault finding – Interpretation of statuses
ET042
CRUISE-CONTROL/SPEED LIMITER
NOTESThere must be no present or stored faults.
IMPORTANT
To remove or check the cruise control/speed limiter control switches you need
to remove the airbag (see MR 364 Mechanical, 88C, Airbag and pretensioners).
NOT DETECTEDIf the vehicle does not have buttons for the cruise control or speed limiter functions,
status ET042 is permanently NOT DETECTED.
This confirms that the cruise control/speed limiter function is not present on the vehicle.
If the vehicle is fitted with cruise control or speed limiter function buttons, the main switch
is in rest (or neutral) position and the injection computer has just been programmed or
reprogrammed, then status ET042 is NOT DETECTED.
To activate the cruise control or speed limiter function, press the main switch in the cruise
control position and then in the speed limiter position.
Return to rest position.
The tool displays status ET042: INACTIVE.
If not, several steps must be checked:
1 Return to the page on testing the multiplex network with the CLIP program.
Repeat the multiplex network test. Re-establish dialogue with the injection
computer. Check status ET042. If ET042 is INACTIVE, the injection computer has
detected the various positions of the main switch. The cruise control/speed limiter is
active.
2 If status ET042 is still NOT DETECTED, check that the vehicle's owner has not had
the cruise control/speed limiter function disabled in the past. Contact the Techline.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
JSAA741.0

PETROL INJECTION
Fault finding – Interpretation of statuses17B
17B - 148V12 MR-372-J84-17B000$540.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
ET415
1(CONTINUED)
STATUS 2Brake pedal depressed
The cruise control function is deactivated when the brake pedal is depressed.
Status ET415 becomes STATUS 2 when driving with cruise control active (ET042
Cruise control/Speed limiter: CRUISE CONTROL) and the brake pedal is depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ007
“Fault memory”.
If status ET415 becomes STATUS 2 without depressing the brake pedal, consult the
interpretation of statuses ET704 Brake switch no. 1 and ET705 Brake switch no. 2.
STATUS 3Clutch pedal depressed
Manual gearbox ONLY
The cruise control function is deactivated when the gearbox is not coupled to the engine
(clutch pedal depressed).
Status ET415 becomes STATUS 3 when driving with cruise control active (ET042
Cruise control/speed limiter: CRUISE CONTROL) and the clutch pedal is depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ007
“Fault memory”.
If status ET415 becomes STATUS 3 without the clutch pedal being depressed, consult
the interpretation of status ET405: Clutch pedal.
If the vehicle is fitted with an automatic transmission:
Test the multiplex network: check the configuration of the multiplex network in relation to
the vehicle's technical specification, especially the configuration of the automatic
transmission computer (see 88B, Multiplexing)
STATUS 4Cancel button pressed
The cruise control/speed limiter function is deactivated whenever the suspend button is
pressed.
Status ET415 becomes STATUS 4 while driving when:
- the cruise control is active, or
- The speed limiter is active,
- and the driver presses the 0 button.
This action deactivates the Cruise control/Speed limiter.
Reinitialise status ET415 on the injection computer by running command RZ007
“Fault memory”.
If status ET415 becomes STATUS 4 without pressing the 0 button, consult the
interpretation of status ET703 Cruise control/speed limiter buttons and run fault
finding on the R/0 control button located on the right-hand side of the steering wheel.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool
JSAA741.0

PETROL INJECTION
Fault finding – Interpretation of statuses17B
17B - 149V12 MR-372-J84-17B000$540.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
ET415
(CONTINUED 2)
STATUS 5Cruise control or speed limiter monitoring
This status appears when the vehicle brakes or decelerates sharply without the injection
computer receiving a signal indicating that the brake pedal switch has been pressed.
If status ET415 is STATUS 5, refer to the interpretation of:
- status ET042 Cruise control/Speed limiter,
- status ET703 Cruise control/speed limiter buttons,
- status ET704 Brake switch no. 1,
- and status ET705 Brake switch No 2,
to test the cruise control/speed limiter system components and find the defective
component.
In addition, check the operation of the accelerator pedal, and use the diagnostic tool to
check for a fault on it. Deal with them if necessary.
Reinitialise status ET415 on the injection computer by running command RZ007
“Fault memory”.
If status ET415 changes to STATUS 5, deal with present faults or those stored in the
injection computer.
If the fault is still present, contact Techline.
STATUS 6Gear lever in neutral (manual gearbox) or the neutral position (automatic gearbox)
Status ET415 becomes STATUS 6, when driving with cruise control active (ET042:
Cruise control/speed limiter: CRUISE CONTROL) and:
- If the driver puts the gear lever in neutral position on a manual gearbox without
declutching or,
- if the gear lever is in neutral on an automatic gearbox.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ007
“Fault memory”.
If status ET415 becomes STATUS 6 without shifting the gear lever into neutral on a
manual gearbox without declutching, or into neutral on an automatic transmission, run
fault finding on the ABS computer and check the configuration of the tyre size stored in
the computer. If the configuration is correct, contact the Techline.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
1JSAA741.0

PETROL INJECTION
Fault finding – Interpretation of statuses17B
17B - 152V12 MR-372-J84-17B000$540.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
ET703
CRUISE CONTROL/SPEED LIMITER BUTTONS
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system programming
functions.
INACTIVEStatus ET703 becomes "INACTIVE" when none of the cruise control/speed limiter
buttons is pressed. These buttons are located on the steering wheel.
If status ET703 does not display "INACTIVE",
●check the condition of the cruise control/speed limiter +/- button and the condition of
its connector,
check the condition of the cruise control/speed limiter R/0 button and the condition of its
connector.
INCREASEStatus ET703 becomes PLUS when the cruise control/speed limiter + button is pressed.
This button is on the steering wheel, on the left-hand side.
If status ET703 does not display PLUS, check the condition of the cruise control/speed
limiter +/- button, and the condition of its connector. Repair if necessary.
To carry out these checks and measurements in complete safety, observe the
recommendations for removing the driver's front airbag (see MR 364/370 Mechanical,
Electrical equipment 88C, Airbag and seat belt pretensioners, Driver's front
airbag, Removal - Refitting).
●Measure the resistance on the button between tracks P1 and P0 while pressing
the “+” button of component 331.
If the resistance is not approximately 300 , check the continuity of the connection when
the button is not pressed.
If there is continuity, replace the +/- control button.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Repair precautions), repair the wiring, otherwise replace it.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
JSAA741.0