radio RENAULT TWINGO 2009 2.G Air Conditioning Owner's Manual

61A-51
HEATING
Heater matrix: Removal - Refitting
RIGHT-HAND DRIVE
61A
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the bolt (6) from the heater matrix pipe bracket on
the distribution unit,
-the heater matrix pipe bracket on the distribution
unit,
-the bolt (7) from the heater matrix pipe bracket.
-the heater matrix pipe bracket,
-the heater matrix bolts (8) .
aPut a container in place to recover the coolant.
aRemove the heater matrix and its pipes.
aUnclip the pipe bracket.
aRemove the heater matrix pipes.
REFITTING
I - REMOVAL PREPARATION OPERATION
aAlways replace the seals between the pipes and the
heater matrix.II - REFITTING OPERATION FOR PART
CONCERNED
aFit the pipes on the heater matrix with new seals.
aClip on the pipe bracket.
aRefit the heater matrix and its pipes.
aRefit:
-the heater matrix bolts,
-the heater matrix pipe bracket,
-the bolt on the heater matrix pipe bracket,
-the heater matrix pipe bracket on the distribution
unit,
-the heater matrix pipe bracket bolt on the distribu-
tion unit.
III - FINAL OPERATION
aRemove the protective cover on the floor carpet.
aRefit:
-the dashboard (see Dashboard: Removal - Refit-
ting) (57A, Interior equipment),
-the central console (see Centre console: Remov-
al - Refitting) (57A, Interior equipment).
aRefit the storage compartment.
aRefit the radio (see Radio: Removal - Refitting)
(86A, Radio).
aRefit the tweeters (see Tweeter: Removal - Refit-
ting) (86A, Radio).
aRefit:
-the control panel (see 61A, Heating, Control pan-
el: Removal - Refitting, page 61A-65) ,
119704
WARNING
To avoid any leaks, check that the pipe surface is
sound before positioning the new seal. The sur-
face must be clean and scratch free.
WITH 2 SPEAKERS, WITHOUT RADIO or VEHI-
CLE WITHOUT RADIO
RADIO NO. 01 or RADIO NO. 03
WITH 2 SPEAKERS, WITHOUT RADIO or RADIO
NO. 01 or RADIO NO. 03

61A-55
HEATING
Fan assembly: Removal - Refitting
RIGHT-HAND DRIVE
61A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).
aRemove:
-the driver's front airbag (see Driver's frontal air-
bag: Removal - Refitting) (MR 411, 88C, Airbags
and pretensioners),
-the steering wheel (see Steering wheel: Removal
- Refitting) (MR 411, 36B, Power-assisted steer-
ing),
-the steering column switch assembly (see Steer-
ing column switch assembly: Removal - Refit-
ting) (MR 411, 84A, Control - Signals),
-the passenger's front airbag (see Passenger's
frontal airbag: Removal - Refitting) (MR 411,
88C, Airbags and seat belt pretensioners),
-the instrument panel (see Instrument panel: Re-
moval - Refitting) (MR 411, 83A, Instrument pan-
el),
-the control panel (see 61A, Heating, Control pan-
el: Removal - Refitting, page 61A-65) .
aRemove the tweeter speakers (see Tweeter: Re-
moval - Refitting) (MR 411, 86A, Radio).
aRemove the radio (see Radio: Removal - Refitting)
(MR 411, 86A, Radio).aRemove the glovebox.
aRemove:
-the centre console (see Centre console: Removal
- Refitting) (MR 412, 57A, Interior equipment),
-the dashboard (see Dashboard: Removal - Refit-
ting) (MR 412, 57A, Interior equipment).
II - REMOVAL OPERATION FOR PART
CONCERNED
aUnclip the fan assembly wiring (1) .
aUnclip the blower unit connector (2) .
aLift the blower unit connector.
aDisconnect the blower unit connector. Equipment required
Diagnostic tool
WITH 2 SPEAKERS, WITHOUT RADIO or RADIO
NO. 01 or RADIO NO. 03
RADIO NO. 01 or RADIO NO. 03
WITH 2 SPEAKERS, WITHOUT RADIO or VEHI-
CLE WITHOUT RADIO
124107

61A-56
HEATING
Fan assembly: Removal - Refitting
RIGHT-HAND DRIVE
61A
aPress on the blower unit tab (3) .
aTurn the blower unit a quarter of a turn clockwise.
aRemove the blower unit (4) .
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit the blower unit.
aPress on the blower unit tab.
aTurn the blower unit a quarter of a turn anti-clock-
wise.
aCheck that the blower unit is in place.
aConnect the blower unit connector.
aClip on the blower unit connector.
aClip on the fan assembly connector wiring.
II - FINAL OPERATION.
aRefit:
-the dashboard (see Dashboard: Removal - Refit-
ting) (MR 412, 57A, Interior equipment),
-the centre console (see Centre console: Removal
- Refitting) (MR 412, 57A, Interior equipment).aRefit the glovebox.
aRefit the radio (see Radio: Removal - Refitting)
(MR 411, 86A, Radio).
aRefit the tweeter speakers (see Tweeter: Removal
- Refitting) (MR 411, 86A, Radio).
aRefit:
-the control panel (see 61A, Heating, Control pan-
el: Removal - Refitting, page 61A-65) ,
-the instrument panel (see Instrument panel: Re-
moval - Refitting) (MR 411, 83A, Instrument pan-
el),
-the passenger's front airbag (see Passenger's
frontal airbag: Removal - Refitting) (MR 411,
88C, Airbags and seat belt pretensioners),
-the steering column switch assembly (see Steer-
ing column switch assembly: Removal - Refit-
ting) (MR 411, 84A, Control - Signals),
-the steering wheel (see Steering wheel: Removal
- Refitting) (MR 411, 36B, Power-assisted steer-
ing),
-the driver's front airbag (see Driver's frontal air-
bag: Removal - Refitting) (MR 411, 88C, Airbags
and seat belt pretensioners).
aConnect the battery (see Battery: Removal - Refit-
ting) (MR 411, 80A, Battery).
aUnlock the airbag computer using the Diagnostic
tool (see Fault finding - Replacement of compo-
nents) (MR 413, 88C, Airbags and pretensioners).
124108
WITH 2 SPEAKERS, WITHOUT RADIO or VEHI-
CLE WITHOUT RADIO
RADIO NO. 01 or RADIO NO. 03
WITH 2 SPEAKERS, WITHOUT RADIO or RADIO
NO. 01 or RADIO NO. 03

61A-57
HEATING
Heating resistors: Removal - Refitting
LEFT-HAND DRIVE
61A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the centre console (see Centre console:
Removal - Refitting) (MR 412, 57A, Interior equip-
ment).
aRemove the radio (see Radio: Removal - Refitting)
(MR 411, 86A, Radio).
aUnclip the glovebox.
aRemove the dashboard lower trim (see Centre front
panel: Removal - Refitting) (MR 412, 57A, Interior
equipment).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect the connector (1) from the heating resis-
tor.
aRemove:
-the heating resistor bolts (2) ,
-the heating resistor.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the heating resistor,
-the heating resistor bolts.
aConnect the heating resistor connector.
II - FINAL OPERATION.
aRefit the dashboard lower trim (see Centre front
panel: Removal - Refitting) (MR 412, 57A, Interior
equipment).
aClip the glovebox in position.
aRefit the radio (see Radio: Removal - Refitting)
(MR 411, 86A, Radio).
aRefit the centre console (see Centre console: Re-
moval - Refitting) (MR 412, 57A, Interior equip-
ment). RADIO NO. 01 or RADIO NO. 03
VEHICLE WITHOUT RADIO
121468
VEHICLE WITHOUT RADIO
RADIO NO. 01 or RADIO NO. 03

61A-71
HEATING
Mixing motor: Removal - Refitting
LEFT-HAND DRIVE, and CLIMATE CONTROL
61A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the centre console (see Centre console:
Removal - Refitting) (MR 412, 57A, Interior equip-
ment).
aRemove the radio (see Radio: Removal - Refitting)
(MR 411, 86A, Radio).
aUnclip the glovebox.
aRemove the dashboard lower trim (see Centre front
panel: Removal - Refitting) (MR 412, 57A, Interior
equipment).
aUnclip:
-the fuse access flap (1) ,-the dashboard lower trim.
aDisconnect the connectors from the lower trim on
the dashboard (2) .
aRemove:
-the steering wheel lower cover bolts (3) ,
-the steering wheel lower cover.
aRemove:
-the bolts (4) from the strut,
-the strut. Tightening torquesm
strut bolts21 Nm
RADIO NO. 01 or RADIO NO. 03
WITH 2 SPEAKERS, WITHOUT RADIO or VEHI-
CLE WITHOUT RADIO
119506
119711
119713

61A-72
HEATING
Mixing motor: Removal - Refitting
LEFT-HAND DRIVE, and CLIMATE CONTROL
61A
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect the connector (5) from the mixer motor.
aRemove:
-the bolts (6) from the air mixing motor,
-the air mixing motor.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the air mixing motor,
-the air mixing motor bolts.
aConnect the air mixing motor connector.
II - FINAL OPERATION.
aRefit:
-the strut,
-the strut bolt.
aTorque tighten the strut bolts (21 Nm).aRefit:
-the steering wheel lower cover,
-the steering wheel lower cover bolt.
aConnect the connectors to the lower trim on the
dashboard.
aClip on:
-the dashboard lower trim,
-the fuse access flap.
aRefit the dashboard lower trim (see Centre front
panel: Removal - Refitting) (MR 412, 57A, Interior
equipment).
aClip the glovebox in position.
aRefit the radio (see Radio: Removal - Refitting)
(MR 411, 86A, Radio).
aRefit the centre console (see Centre console: Re-
moval - Refitting) (MR 412, 57A, Interior equip-
ment).
aCheck that the air mixing function is operating cor-
rectly.
121173
Note:
When refitting the mixer motor, make sure that
the drive system notches are correctly posi-
tioned.
WITH 2 SPEAKERS, WITHOUT RADIO or VEHI-
CLE WITHOUT RADIO
RADIO NO. 01 or RADIO NO. 03

61A-73
HEATING
Mixing motor: Removal - Refitting
RIGHT-HAND DRIVE, and CLIMATE CONTROL
61A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aDisconnect the battery (see ) (MR 411, 80A, Bat-
tery).
aRemove the radio (see Radio: Removal - Refitting)
(MR 411, 86A, Radio).
aDisconnect the connectors (1) from the dashboard
lower trim.
aRemove the dashboard lower trim.
aRemove:
-the centre console (see Centre console: Removal
- Refitting) (MR 412, 57A, Interior equipment),
-the centre front panel (see Centre front panel: Re-
moval - Refitting) (MR 412, 57A, Interior equip-
ment).
aRemove the tweeter speakers (see Tweeter: Re-
moval - Refitting) (MR 411, 86A, Radio).aRemove the radio (see Radio: Removal - Refitting)
(MR 411, 86A, Radio).
aRemove the glovebox.
II - REMOVAL OPERATION FOR PART
CONCERNED
aDisconnect the connector (2) from the mixer motor.
aRemove the air mixing motor bolts (3) .
aMove the air mixing motor aside. RADIO NO. 01 or RADIO NO. 03
124103
WITH 2 SPEAKERS, WITHOUT RADIO or RADIO
NO. 01 or RADIO NO. 03
RADIO NO. 01 or RADIO NO. 03
WITH 2 SPEAKERS, WITHOUT RADIO or VEHI-
CLE WITHOUT RADIO
124369

61A-74
HEATING
Mixing motor: Removal - Refitting
RIGHT-HAND DRIVE, and CLIMATE CONTROL
61A
aUnclip the rod (4) from the air mixing motor by tilting
the motor downwards.
aRemove the air mixing motor.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aClip the rod onto the air mixing motor.
aFit the air mixing motor.
aRefit:
-the air mixing motor,
-the air mixing motor bolts.
aConnect the air mixing motor connector.
II - FINAL OPERATION.
aRefit the glovebox.aRefit the radio (see Radio: Removal - Refitting)
(MR 411, 86A, Radio).
aRefit the tweeter speakers (see Tweeter: Removal
- Refitting) (MR 411, 86A, Radio).
aRefit:
-the centre front panel (see Centre front panel: Re-
moval - Refitting) (MR 412, 57A, Interior equip-
ment).
-the centre console (see Centre console: Removal
- Refitting) (MR 412, 57A, Interior equipment),
aConnect the connectors to the lower trim on the
dashboard.
aRefit the dashboard lower trim.
aRefit the radio (see Radio: Removal - Refitting)
(MR 411, 86A, Radio).
aConnect the battery (see ) (MR 411, 80A, Battery).
124369
Note:
When refitting the mixer motor, make sure that
the drive system notches are correctly posi-
tioned.
WITH 2 SPEAKERS, WITHOUT RADIO or VEHI-
CLE WITHOUT RADIO
RADIO NO. 01 or RADIO NO. 03
WITH 2 SPEAKERS, WITHOUT RADIO or RADIO
NO. 01 or RADIO NO. 03
RADIO NO. 01 or RADIO NO. 03

61A-75
HEATING
Distribution motor: Removal - Refitting
LEFT-HAND DRIVE, and CLIMATE CONTROL
61A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the centre console (see Centre console:
Removal - Refitting) (MR 412, 57A, Interior equip-
ment).
aRemove the radio (see Radio: Removal - Refitting)
(MR 411, 86A, Radio).
aUnclip the glovebox.
aRemove the dashboard lower trim (see Centre front
panel: Removal - Refitting) (MR 412, 57A, Interior
equipment).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aUnclip the distribution motor control rod (1) .
aRemove the distribution motor bolts (2) .
aDisconnect the distribution motor connector (3) .
aRemove the distribution motor.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the distribution motor,
-the distribution motor bolts.
aConnect the distribution motor connector.
aClip on the distribution motor control rod.
II - FINAL OPERATION.
aRefit the dashboard lower trim (see Centre front
panel: Removal - Refitting) (MR 412, 57A, Interior
equipment).
aClip the glovebox in position.
aRefit the radio (see Radio: Removal - Refitting)
(MR 411, 86A, Radio).
aRefit the centre console (see Centre console: Re-
moval - Refitting) (MR 412, 57A, Interior equip-
ment).
aCheck that the air distribution function is operating
correctly. RADIO NO. 01 or RADIO NO. 03
WITH 2 SPEAKERS, WITHOUT RADIO or VEHI-
CLE WITHOUT RADIO
121177
Note:
When refi tting the distribution motor, make sure
that the drive system notches are correctly posi-
tioned.
WITH 2 SPEAKERS, WITHOUT RADIO or VEHI-
CLE WITHOUT RADIO
RADIO NO. 01 or RADIO NO. 03

61A-76
HEATING
Distribution motor: Removal - Refitting
RIGHT-HAND DRIVE, and CLIMATE CONTROL
61A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the centre console (see Centre console:
Removal - Refitting) (57A, Interior equipment).
aRemove the radio (see Radio: Removal - Refitting)
(86A, Radio).
aUnclip the storage compartment.
aRemove:
-the dashboard lower trim (see Centre front panel:
Removal - Refitting) (57A, Interior equipment),
-the centre front panel (see Centre front panel: Re-
moval - Refitting) (57A, Interior equipment).aRemove the upper bolts (1) from the dashboard
cross member reinforcement.
aRemove the floor carpet on the driver's side.
aRemove the lower bolts (2) from the dashboard
cross member reinforcement. Tightening torquesm
dashboard cross mem-
ber reinforcement bolts21 Nm
RADIO NO. 01 or RADIO NO. 03
WITH 2 SPEAKERS, WITHOUT RADIO or VEHI-
CLE WITHOUT RADIO
141233
141234