RENAULT TWINGO 2009 2.G Electrical Equipment - Instrument Panel Service Manual

83A-41
MR-413-X44-83A000$616.mif
V5
INSTRUMENT PANEL
Fault finding - Interpretation of statuses

Vdiag No.: 04, 08
83A
ET248
STOP WARNING LIGHT ACTIVATED BY THE SYSTEM
If the STOP WARNING LIGHT is illuminated, check for faults and check the conformity of the systems
concerned.
1 : Injection
2 : Coolant temperature
3 : Oil pressure
Perform fault finding on the injection system:
–Petrol: See 17B, Petrol injection,
–Diesel: See 13B, Diesel injection.
4 : Brake fluid level
See the interpretation of ET019 MINIMUM BRAKE FLUID LEVEL.
5 : Electronic Braking Distribution
Carry out fault finding on the ABS/ESP system (see 38C, Anti-lock braking system).
6 : Electric power assisted steering
Carry out fault finding on the EPAS system (see 36B, Power-assisted steering).
7 : Battery charge
Carry out fault finding on the charging circuit (see Technical Note 6014A, Checking the charging circuit).
If there are no faults, carry out a multiplex network check (see 88B, Multiplex).
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
TDB_V04_ET248 / TDB_V08_ET248

83A-42
MR-413-X44-83A000$616.mif
V5
INSTRUMENT PANEL
Fault finding - Interpretation of statuses

Vdiag No.: 04, 08
83A
ET249
SERVICE WARNING LIGHT ACTIVATED BY THE SYSTEM
If the SERVICE WARNING LIGHT is illuminated, check for faults and check the conformity of the systems
concerned.
1 : Multiplex line communication
Check the multiplex network (see 88B, Multiplex)
2 : Injection
3 : Water present in diesel fuel
Perform fault finding on the injection system:
–Petrol: See 17B, Petrol injection,
–Diesel: See 13B, Diesel injection.
4 : Sequential gearbox
Carry out fault finding on the sequential gearbox (see 23A, Sequential gearbox).
5 : Vehicle speed circuit
Carry out fault finding on the ABS/ESP system (see 38C, Anti-lock braking system).
6 : Cruise control/speed limiter
Perform fault finding on the injection system:
–Petrol: See 17B, Petrol injection,
–Diesel: See 13B, Diesel injection.
7 : ESP
8 : ABS
Carry out fault finding on the ABS/ESP system (see 38C, Anti-lock braking system).
9 : Oil service interval
Perform fault finding on the injection system:
–Petrol: See 17B, Petrol injection,
–Diesel: See 13B, Diesel injection.
10 : Particle filter
Perform fault finding on the injection system:
–Petrol: See 17B, Petrol injection,
–Diesel: See 13B, Diesel injection.
11 : Airbag
Carry out fault finding on the Airbag system (see 88C, Airbag and pretensioners).
12 : OBD
Perform fault finding on the injection system:
–Petrol: See 17B, Petrol injection,
–Diesel: See 13B, Diesel injection.
If there are no faults, carry out a multiplex network check (see 88B, Multiplex).
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
TDB_V04_ET249 / TDB_V08_ET249

83A-43
MR-413-X44-83A000$672.mif
V5
83A
INSTRUMENT PANEL
Fault finding - Parameter summary table
Tool parameter Diagnostic tool title
PR041Filtered fuel level

Vdiag No.: 04, 08
MR-413-X44-83A000$672.mif

83A-44
MR-413-X44-83A000$728.mif
V5
83A
INSTRUMENT PANEL
Fault finding - Interpretation of parameters
PR041 Filtered fuel level
NOTESIn the event of a fuel sender fault, check for the presence of DF007 FUEL SENDER
first.
This value is used to display the fuel level, i.e. the number of illuminated squares on the instrument panel.
Reference table displaying the filtered fuel level (PR041) in relation to the number of illuminated squares.
–0l to 5l: reserve square
–5l to 8l: 1 square
–8l to 12l: 2 squares
–12l to 18l: 3 squares
–18l to 25l: 4 squares
–25l to 32l: 5 squares
–32l to 37l: 6 squares
–37l to full: 7 squares
IMPORTANT
Once a square is no longer lit, it can not be relit except by adding fuel to the tank or running command VP020
UPDATE FUEL LEVEL DISPLAY.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
TDB_V04_PR041 / TDB_V08_PR041

Vdiag No.: 04, 08
MR-413-X44-83A000$728.mif

83A-45
MR-413-X44-83A000$784.mif
V5
83A
INSTRUMENT PANEL
Fault finding - Command summary table
Tool command Diagnostic tool title
VP020Update fuel level display
RZ001Fault memory

Vdiag No.: 04, 08
MR-413-X44-83A000$784.mif

83A-46
MR-413-X44-83A000$840.mif
V5
83A
INSTRUMENT PANEL
Fault finding - Interpretation of commands
VP020 UPDATE FUEL LEVEL DISPLAY
This command is used for updating the fuel level display.
Once the command has been run, PR040 CURRENT FUEL LEVEL and PR041 FILTERED FUEL LEVEL
must produce equivalent values.
In the event of a fault, refer to the interpretation of fault DF007 Fuel sender circuit.
TDB_V04_VP020 / TDB_V08_VP020

Vdiag No.: 04, 08
MR-413-X44-83A000$840.mif

83A-47
MR-413-X44-83A000$840.mif
V5
INSTRUMENT PANEL
Fault finding - Interpretation of commands

Vdiag No.: 04, 08
83A
RZ001 FAULT MEMORY
This command is used to clear the instrument panel system faults.
TDB_V04_RZ001 / TDB_V08_RZ001

83A-48
MR-413-X44-83A000$896.mif
V5
83A
INSTRUMENT PANEL
Fault finding - Customer complaints
NOTESOnly refer to the customer complaints after a complete check using the diagnostic
tool
Carry out fault finding on the multiplex network.
Carry out fault finding on the instrument panel.
NO COMMUNICATION WITH THE INSTRUMENT PANEL
THE INSTRUMENT PANEL DOES NOT LIGHT UPALP 1
THE FUEL LEVEL INDICATOR DOES NOT DISPLAY FULL
ALP 2
ADDITION OF FUEL NOT REGISTERED (NOT FULL)
ALP 3
DISPLAY JAMMED WHEN DRIVING (NOT MECHANICAL)
ALP 4
FAULT WITH NO WARNING GIVEN BY WARNING LIGHT (NO ADDITION OF FUEL
SINCE THE FAULT)ALP 5
FAULT WITH NO WARNING GIVEN BY WARNING LIGHT (ADDITION OF FUEL SINCE
THE FAULT)ALP 6
FAULT WITH DELAYED WARNING
ALP 7

Vdiag No.: 04, 08
MR-413-X44-83A000$896.mif

83A-49
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
83A
Vdiag No.: 04 08
ALP 1NO COMMUNICATION WITH THE INSTRUMENT PANEL.
The instrument panel does not light up.
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
See Wiring diagram Technical Note, New Twingo.
Test the diagnostic tool on another vehicle which is in perfect working order.
Check that the sensor's green indicator light comes on.
If communication with the second vehicle is impossible, follow the instructions in the CLIP diagnostic tool test
section.
If dialogue with the first vehicle is possible, follow the instructions in the Vehicle check section.
DIAGNOSTIC
TOOL CHECKCheck the cleanliness and condition of the contacts of the diagnostic socket,
component code 225 connected to the vehicle.
Check the condition of the cable from the diagnostic socket to the sensor and the
cleanliness and condition of the connections.
Check the sensor connections.
Check the condition of the cable from the CLIP tool to the sensor as well as the
condition and cleanliness of the connections.
Check the cleanliness and condition of the CLIP socket.
If the connector or connectors are faulty and if there is a repair procedure (see
Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the connector, otherwise replace the wiring.
If the fault is still present, contact Techline.
TDB_V04_ALP1/TDB_V08_ALP1
INSTRUMENT PANEL
Fault finding - Fault finding chart

83A-50
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
INSTRUMENT PANEL
Fault finding - Fault finding chart Vdiag No.: 04, 0883A
Vdiag No.: 04 08
ALP 1
CONTINUED 1
VEHICLE CHECK
Check the cleanliness and condition of the contacts of the diagnostic socket,
component code 225 connected to the vehicle.
Check the condition of the cable from the diagnostic socket to the sensor and the
cleanliness and condition of the connections.
Check the sensor connections.
Check the condition of the cable from the sensor to the CLIP tool and the cleanliness
and condition of the connections.
Check the cleanliness and condition of the CLIP socket.
If the connector or connectors are faulty and if there is a repair procedure (see
Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the connector, otherwise replace the wiring.
If the fault is still present, contact Techline.
Check the condition and connection of the instrument panel connector, component
code 247.
If the connector is faulty and there is a repair method (see Technical Note 6015A,
Repairing electrical wiring, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Check instrument panel supply fuse MIN (5 A), component code 247 on the passenger
compartment fuse box, component code 1016 and the condition and cleanliness of
the contacts.
Check the instrument panel after ignition supply fuse MIN (15 A), component code
247 on the passenger compartment fuse box, component code 1016, and the
condition and cleanliness of the contacts.