RENAULT TWINGO 2009 2.G Engine And Peripherals Multimedia Connection Unit Owner's Guide

86D-31V1 MR-413-X44-86D000$100.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Conformity check86D
BIC
Vdiag No.: 14
FUNCTION: MULTIMEDIA
SUB-FUNCTION: DISPLAY
NOTESOnly carry out a conformity check after a complete check with the diagnostic tool. The
values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status
Checked or actionDisplay and notes Fault finding
DisplayAC001:Display testThis command is used
to test the liquid crystal
screen of the display.None
LightingET004:+12 V Side lightsOFF
ON
INVALID
INACTIVEIn the event of an
inconsistency, run fault
finding on the UCH (see
87B, Passenger
compartment
connection unit).
ET007:BrightnessPANEL GAP
NIGHTIn the event of an
inconsistency, consult the
interpretation of ALP 4
Lighting does not
change when the
vehicle lights are
switched on.

86D-32V1 MR-413-X44-86D000$110.mif
86D
BIC
Vdiag No.: 14
Tool status Diagnostic tool title
ET002Radio on/off button
ET004+12 V Side lights
ET007Brightness
ET009Repeat button (only on Clio III)
ET011+ button
ET012- button
ET017Wheel action
ET020Mute button
ET023Source button
ET024Mode button
ET055Telephone button
MULTIMEDIA CONNECTION UNIT
Fault finding – Status summary table

86D-33
AFTER REPAIRRepeat the conformity check from the start.
V1 MR-413-X44-86D000$120.mif
86D
BIC
Vdiag No.: 14
ET009
ET011
ET012
ET020
ET023
ET024
ET025REPEAT BUTTON
+ BUTTON
- BUTTON
MUTE BUTTON
SOURCE BUTTON
MODE BUTTON
TELEPHONE BUTTON
STATUS DEFINITIONPRESSED: This means that the button is pressed.
RELEASED: This means that the button is released.
NOTESThere must be no present or stored faults.
Note: ET009 Repeat button is not present on the New Twingo.
For a vehicle equipped with a Navigation computer, use component 1714, Multimedia
connection unit, for fault finding on the Multimedia interface unit.
Otherwise use component 653, display computer.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
Check the condition and connection:
●of the radio control satellite connector, component code 1519 (for Clio III) or component code 325 (for New
Twingo).
●of the display connector, component code 653, or the multimedia connection unit connector, component code
1714, depending on the vehicle equipment.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
BIC_V14_ET009 / BIC_V14_ET011 / BIC_V14_ET012 / BIC_V14_ET020 / BIC_V14_ET023 / BIC_V14_ET024 / BIC_V14_ET025
MULTIMEDIA CONNECTION UNIT
Fault finding – Interpretation of statuses

86D-34
AFTER REPAIRRepeat the conformity check from the start.
V1 MR-413-X44-86D000$120.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Interpretation of statuses86D
BIC
Vdiag No.: 14
ET009
ET011
ET012
ET020
ET023
ET024
ET025
CONTINUED
Using the universal bornier, check the insulation, continuity and the absence of interference resistance on
the following connections:
●34AT between components 1519 (or 325) and 653 (or 1714),
●34AR between components 1519 (or 325) and 653 (or 1714),
●34AS between components 1519 (or 325) and 653 (or 1714),
●34AQ between components 1519 (or 325) and 653 (or 1714),
●34AU between components 1519 (or 325) and 653 (or 1714),
●34AP between components 1519 (or 325) and 653 (or 1714).
●34AO between components 1519 and 653 (or 1714) (only for Clio III).
If the connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the wiring, otherwise change the wiring.
Replace the radio control satellite (see MR 392 (Clio III) or MR 411 (New Twingo), Mechanical, 86A, Radio,
Radio satellite control: Removal - Refitting).
If the vehicle is equipped with a Navigation computer (only on Clio III), replace the multimedia connection unit (see
MR 392, Mechanical, 83C, On-board telematics system, Multimedia network interface unit: Removal -
Refitting).
If the vehicle is not equipped with a Navigation computer, replace the display (see MR 392 (Clio III) or MR 411
(New Twingo), Mechanical, 86A, Radio, Display: Removal - Refitting).
If the fault is still present, contact Techline.

86D-35
AFTER REPAIRRepeat the conformity check from the start.
V1 MR-413-X44-86D000$120.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Interpretation of statuses86D
BIC
Vdiag No.: 14
ET017WHEEL ACTION
STATUS DEFINITIONDownwards: This means that the wheel is turned downwards.
Upwards: This means that the wheel is turned upwards.
Inactive: This means that there is no action on the wheel.
NOTESThere must be no present or stored faults.
For a vehicle equipped with a Navigation computer, use component 1714, Multimedia
connection unit, for fault finding on the Multimedia interface unit.
Otherwise use component 653, display computer.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
Check the condition and connection:
●of the radio control satellite connector, component code 1519 (for Clio III) or component code 325 (for New
Twingo).
●of the display connector, component code 653, or the multimedia connection unit connector, component code
1714, depending on the vehicle equipment.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Using the universal bornier, check the insulation, continuity and the absence of interference resistance on the
following connections:
●34AT between components 1519 (or 325) and 653 (or 1714),
●34AR between components 1519 (or 325) and 653 (or 1714),
●34AS between components 1519 (or 325) and 653 (or 1714),
●34AQ between components 1519 (or 325) and 653 (or 1714),
●34AU between components 1519 (or 325) and 653 (or 1714),
●34AP between components 1519 (or 325) and 653 (or 1714).
●34AO between components 1519 and 653 (or 1714) (only for Clio III).
If the connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the wiring, otherwise change the wiring.
BIC_V14_ET017

86D-36
AFTER REPAIRRepeat the conformity check from the start.
V1 MR-413-X44-86D000$120.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Interpretation of statuses86D
BIC
Vdiag No.: 14
ET017
CONTINUED
Replace the radio control satellite (see MR 392 (Clio III) or MR 411 (New Twingo), Mechanical, 86A, Radio,
Radio satellite control: Removal - Refitting).
If the vehicle is equipped with a Navigation computer (only on Clio III), replace the multimedia connection unit (see
MR 392, Mechanical, 83C, On-board telematics system, Multimedia network interface unit: Removal -
Refitting).
If the vehicle is not equipped with a Navigation computer, replace the display (see MR 392 (Clio III) or MR 411
(New Twingo), Mechanical, 86A, Radio, Display: Removal - Refitting).
If the fault is still present, contact Techline.

86D-37V1 MR-413-X44-86D000$130.mif
86D
BIC
Vdiag No.: 14
Tool Parameter Diagnostic tool title
PR002Battery voltage
PR003Vehicle speed
PR004External temperature
MULTIMEDIA CONNECTION UNIT
Fault finding – Parameter summary table

86D-38V1 MR-413-X44-86D000$140.mif
86D
BIC
Vdiag No.: 14
Tool
commandDiagnostic tool title Description
RZ001:Fault memoryThis command is used for clearing the stored
faults from the computer.
AC001:Display testThis command is used to test the liquid crystal
screen of the display.
AC002:On/Off ButtonThis command is used to simulate the pressing
of the On/Off button of the radio.
MULTIMEDIA CONNECTION UNIT
Fault finding – Command summary table

86D-39V1 MR-413-X44-86D000$150.mif
86D
BIC
Vdiag No.: 14
NOTESOnly refer to the customer complaints after performing a complete check using
the diagnostic tool.
NO DIALOGUE WITH THE COMPUTER ALP 1
THE RADIO CONTROL SATELLITE DOES NOT OPERATE OR OPERATES POORLY ALP 2
THE VOLUME DOES NOT INCREASE WITH THE VEHICLE SPEED ALP 3
THE RADIO AND/OR THE DISPLAY REMAINS LIT FOR 1 MINUTE AFTER LOCKING THE
VEHICLE (ON NEW TWINGO ONLY)ALP 4
MULTIMEDIA CONNECTION UNIT
Fault finding – Customer complaints

86D-40
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V1 MR-413-X44-86D000$160.mif
86D
BIC
Vdiag No.: 14
ALP 1 No dialogue with the computer
NOTESFor a vehicle equipped with a Navigation computer, use component 1714, Multimedia
connection unit, for fault finding on the Multimedia interface unit.
Otherwise use component 653, display computer.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
Try to establish dialogue with a computer on another vehicle to check that the diagnostic tool is not faulty. If the
diagnostic tool is not causing the fault and dialogue cannot be established with any other computer on the same
vehicle, it may be that a faulty computer is disrupting the fault finding line.
Use a process of successive disconnections to locate this computer.
Check the battery voltage, component code 107, and perform the necessary operations to obtain the correct
voltage (12 V < X < 15 V).
Check the presence and condition of the computer supply fuses:
–for New Twingo: F48 (15 A),
–for Clio III: F14 (5 A), F2 (20 A) and unit fuse 710 (15 A).
Check the connection of the display connector, component code 653, or the multimedia connection unit connector,
component code 1714, and the condition of its connections.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check that the computer is correctly supplied by checking the following connections:
–BCP4 between components 260 and 653 or 1714,
–BPT between components 645 and 653 or 1714,
–BPT3 between components 260 and 653 or 1714,
–NAM between component 653 or 1714 and earth.
If the connection(s) is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
A
BIC_V14_ALP1
MULTIMEDIA CONNECTION UNIT
Fault finding – Fault Finding Chart