RENAULT TWINGO 2009 2.G Engine And Peripherals Multimedia Connection Unit Service Manual

86D-41
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V1 MR-413-X44-86D000$160.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Fault Finding Chart86D
BIC
Vdiag No.: 14
ALP 1
CONTINUED
Check that the diagnostic socket, component code 225, is correctly supplied on the following connections:
–for New Twingo:
–BP19 between components 225 and 1016 (+ before ignition feed),
–NAM and MAN (left-hand drive) or MAM (right-hand drive) of component 225.
–for Clio III:
–BP32 between components 225 and 260 (+ before ignition feed),
–NAM and MK of component 225.
Check the continuity and insulation of the following connections:
–107W and 107X between components 225 and 653 or 1714,
–133B and 133C between components 225 and 653 or 1714.
If the connection(s) is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If dialogue is still not established after these various checks, replace the computer, component code 653 (see
MR 392 (Clio III) or MR 411 (New Twingo), Mechanical, 86A, Radio, Display: Removal - Refitting) or 1714
(see MR 392 (Clio III), Mechanical, 83C, On-board telematics system, Multimedia network interface unit:
Removal - Refitting).
If the fault is still present, contact Techline.
A

86D-42
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any faults.
V1 MR-413-X44-86D000$160.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Fault Finding Chart86D
BIC
Vdiag No.: 14
ALP 2 The radio control satellite does not operate or operates poorly
NOTESFor a vehicle equipped with a Navigation computer, use component 1714, Multimedia
connection unit, for fault finding on the Multimedia interface unit.
Otherwise use component 653, display computer.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
Does the display operate?See ALP1 No dialogue with the computer.
Check the statuses of the radio control satellite (see
Conformity check)
Are the checks correct?
Contact the Techline.
NO
YES
YES
NO
A
BIC_V14_ALP2

86D-43
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any faults.
V1 MR-413-X44-86D000$160.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Fault Finding Chart86D
BIC
Vdiag No.: 14
ALP 2
CONTINUED 1
Check the condition and the connection of the satellite
control connector, component code 325 (New Twingo)
or 1519 (Clio III).
If the connector is faulty and there is a repair method (see
Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Check the continuity, insulation and the absence of
interference resistance on the following connections:
●34AT, between components 653 or 1714 and 325
(New Twingo) or 1519 (Clio III),
●34AR, between components 653 or 1714 and 325
(New Twingo) or 1519 (Clio III),
●34AS, between components 653 or 1714 and 325
(New Twingo) or 1519 (Clio III),
●34AQ, between components 653 or 1714 and 325
(New Twingo) or 1519 (Clio III),
●34AU, between components 653 or 1714 and 325
(New Twingo) or 1519 (Clio III),
●34AP between components 653 or 1714 and 325 (New
Twingo) or 1519 (Clio III),
●34AO between components 653 or 1714 and 1519
(Clio III only).
If the connection or connections are faulty
and there is a repair procedure (see
Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it. Are the checks correct?
A
NO
NO
YES
BC

86D-44
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any faults.
V1 MR-413-X44-86D000$160.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Fault Finding Chart86D
BIC
Vdiag No.: 14
ALP 2
CONTINUED 2
Replace the radio control satellite, component code 325
(see MR 392 (Clio III) or MR 411 (New Twingo),
Mechanical, 86A, Radio, Radio satellite control:
Removal - Refitting).
If the fault is still present, contact Techline.
If the fault is still present:
If the vehicle is equipped with a Navigation computer
(only on Clio III), replace the multimedia connection unit
(see MR 392, Mechanical, 83C, On-board telematics
system, Multimedia network interface unit: Removal
- Refitting).
If the vehicle is not equipped with a Navigation computer,
replace the display (see MR 392 (Clio III) or MR 411
(New Twingo), Mechanical, 86A, Radio, Display:
Removal - Refitting).
If the fault is still present, contact Techline
B
YES
C

86D-45
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any faults.
V1 MR-413-X44-86D000$160.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Fault Finding Chart86D
BIC
Vdiag No.: 14
ALP 3 The volume does not increase with the vehicle speed.
NOTESConsult the user manual to make the adjustments.
Check the value of the volume correction
according to the speed.
Is the value 0?Put the value to 2.
Contact the Techline.
YES
NO
BIC_V14_ALP3

86D-46
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any faults.
V1 MR-413-X44-86D000$160.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Fault Finding Chart86D
BIC
Vdiag No.: 14
ALP 4The radio and/or the display remains lit for 1 minute after locking
the vehicle (on New Twingo only)
NOTESNone.
Explain to the customer that this operation is normal on New Twingo.
BIC_V14_ALP4