engine RENAULT TWINGO 2009 2.G Sequential Transmission Owners Manual

21B -129
MR-413-X44-21B000$944.mif
V2
SEQUENTIAL GEARBOX
Diagnostic - Fault finding chart
Vdiag No: 04
21B
ALP 4Cannot access automatic mode if semi-automatic mode was
previously selected
Cannot access semiautomatic mode if automatic mode was
previously selected
Switching to automatic mode possible if restarting engine
NOTESSpecial notes:
Only consult this customer complaint after a complete check with the diagnostic tool.
Use the Wiring Diagrams Technical Note for New TWINGO.
Check the connection and condition of the connectors of components 1058 and 119.
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, W iring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
Apply the interpretation of statuses ET043 “Lever switch no. 0”, ET044 “Lever switch no. 1”, ET045 “Lever
switch no. 2” and ET046 “Lever switch no. 3”.
AFTER REPAIRClear the computer fault memory. Switch off the ignition and wait 20 seconds.
Carry out a road test followed by another check with the diagnostic tool.
BVRJH1_V04_ALP4

21B -133
MR-413-X44-21B000$944.mif
V2
SEQUENTIAL GEARBOX
Diagnostic - Fault finding chart
Vdiag No: 04
21B
ALP 7 Loss of automatic mode
NOTESSpecial notes:
Only consult this customer complaint after a complete check with the diagnostic tool.
Level 1 severity injection fault sent by the engine management via the multiplex line connection.
Using the diagnostic tool, check the injection system (see 17B, Petrol injection).
AFTER REPAIRClear the computer fault memory. Switch off the ignition and wait 20 seconds.
Carry out a road test followed by another check with the diagnostic tool.
BVRJH1_V04_ALP7

21B -134
MR-413-X44-21B000$944.mif
V2
SEQUENTIAL GEARBOX
Diagnostic - Fault finding chart
Vdiag No: 04
21B
ALP 8Vehicle does not move forward with gear engaged and engine
running
NOTESSpecial notes:
Only consult this customer complaint after a complete check with the diagnostic tool.
Apply the fault finding procedure associated with the multiplex network test (see 88B, Multiplexing).
Check the mechanical condition of the clutch (no grease or leaks on the flywheel, clutch driven plate not cracked
or disintegrated, no broken parts, etc.).
Check the condition of the driveshaft (broken joint, internal gearbox mechanical fault etc.).
Repair or replace the faulty components.
If the engine speed remains at idle speed, check the positioning of the accelerator pedal sensor.
Run fault finding on the injection system (see 17B, Petrol Injection).
If the fault is still present, contact Techline.
AFTER REPAIRClear the computer fault memory. Switch off the ignition and wait 20 seconds.
Carry out a road test followed by another check with the diagnostic tool.
BVRJH1_V04_ALP8

21B -137
MR-413-X44-21B000$944.mif
V2
SEQUENTIAL GEARBOX
Diagnostic - Fault finding chart
Vdiag No: 04
21B
ALP 11 Display and warning buzzer operation erratically
NOTESSpecial notes:
Only consult this customer complaint after a complete check with the diagnostic tool.
–The buzzer is active:
–when the front doors are opened,
–if the clutch overheats while the vehicle is being driven,
–if the sequential gearbox programming has not been carried out.
–The depress brake pedal symbol is active:
–when the engine is stopped by a gear lever request or if the lever is accidentally shifted to the neutral
position while the vehicle is being driven.
Carry out a road test to recreate the customer complaint.
Carry out the following programming:
–VP008 “Program selection/engagement ranges”.
–Program the biting point using command:
RZ003 Clutch biting point programming
Exit fault finding mode and switch off the ignition.
Wait 1 minute and then re-establish dialogue with the computer.
Shift the gear lever to rest position (Stb).
Start the engine.
Wait 10 seconds without changing gear (for programming the clutch biting point).
Check that programming has been successfully completed by referring to the following status:
ET062 “Biting point programming” displays “Done”.
Repeat the procedure if unsuccessful.
AFTER REPAIRClear the computer fault memory. Switch off the ignition and wait 20 seconds.
Carry out a road test followed by another check with the diagnostic tool.
BVRJH1_V04_ALP11

21B -138
MR-413-X44-21B000$944.mif
V2
SEQUENTIAL GEARBOX
Diagnostic - Fault finding chart
Vdiag No: 04
21B
ALP 12 Vehicle jumps when engine is started
NOTESSpecial notes:
Only consult this customer complaint after a complete check with the diagnostic tool.
If a gear was engaged when there is a request to start the engine check the oil level in the sequential gearbox
circuit.
Check the operation of the brake pedal switch as well as the condition of the gear lever switches (consult the
interpretation of statuses: ET043 “Lever switch no. 0”, ET044 “Lever switch no. 1”, ET045 “Lever switch
no. 2” and ET046 “Lever switch no. 3”).
Ensure that the cylinder and the clutch fork are operating correctly (damage, seizing, part breakage, etc.).
AFTER REPAIRClear the computer fault memory. Switch off the ignition and wait 20 seconds.
Carry out a road test followed by another check with the diagnostic tool.
BVRJH1_V04_ALP12