fuses RENAULT TWINGO 2009 2.G Sequential Transmission Workshop Manual

21B-24
MR-413-X44-21B000$413.mif
V2
21B
SEQUENTIAL GEARBOX
Fault finding - Interpretation of faults
DF002
PRESENT
OR
STOREDCOMPUTER
1.DEF: Internal electronic fault
NOTESSpecial note:
–fault warning light comes on.
Use the Wiring Diagrams Technical Note for New TWINGO.
Check the condition and positioning of the following fuses:
●Fuse F1 (30A) located in the engine fuse and relay box.
●Fuses F16 (20A) and F4 (7.5A) located in the passenger compartment fuse box.
Check the connection and condition of the 52-track connector of component 119.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check for + before ignition on connection BP39 and for + after ignition feed on connection AP4 on the
connector of component 119.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, W iring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●Connection code N between component 119 and the chassis earth MC - 12A.
●Connection code N between component 119 and the chassis earth MC - 12B.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, W iring: Precautions for repair), repair the wiring, otherwise replace it.
Clear the computer fault memory and exit fault finding.
Switch off the ignition.
Switch on the ignition again and carry out a new check using the diagnostic tool.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
BVRJH1_V04_DF002
MR-413-X44-21B000$413.mif
Vdiag No.: 04

21B-67
MR-413-X44-21B000$472.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of faults
Vdiag No: 04
21B
DF232
DF233
DF234
PRESENT
OR
STOREDCOMPUTER
1.DEF : Internal electronic fault
NOTESSpecial note:
–fault warning light comes on.
Use the Wiring Diagrams Technical Note for New TWINGO.
Check the condition and position of the sequential gearbox fuses in the engine compartment and in the
passenger compartment.
Check the connection and condition of the 52-track connector of component 119.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check for + AVC on connection BP39 and for + after ignition feed on connection AP4 on the 52-track connector
of component 119.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, W iring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation, continuity and the absence of interference resistance on the following connection:
●Connection code N of earths MC - 12B and MC - 12A.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, W iring: Precautions for repair), repair the wiring, otherwise replace it.
Clear the computer fault memory using command RZ001 "Stored fault(s)".
Switch off the ignition.
Switch on the ignition again and carry out a new check using the diagnostic tool.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults detected by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
BVRJH1_V04_DF232 / BVRJH1_V04_DF233 / BVRJH1_V04_DF234

21B-77
MR-413-X44-21B000$472.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of faults
Vdiag No: 04
21B
DF265
PRESENT
OR
STOREDCOMPUTER
1.DEF : Main relay fault (integrated in the computer)
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after a road test.
Special note:
–all gear changes are inhibited,
–automatic mode is inhibited.
Check the condition and connection of the earths on both connections N of component 119.
Check the condition and position of the sequential gearbox fuses in the engine compartment and in the
passenger compartment.
Check the condition and connection of the connectors for component 119.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check for + AVC on connection BP39 of component 119.
If the + AVC is absent, check the insulation to earth and the continuity of the following connection:
●Connection code BP39,
between components 119 and 1016.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
wiring: precautions for repair), repair the wiring, otherwise replace it.
Check for + after ignition feed on connection AP4 of component 119.
If the + after ignition feed is absent, check the insulation to earth and the continuity of the following
connection:
●Connection code AP4,
between components 119 and 1016.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
wiring: precautions for repair), repair the wiring, otherwise replace it.
Clear the computer fault memory using command RZ001 "Stored fault(s)", exit the fault finding and switch off the
ignition.
Carry out another check using the diagnostic tool.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults detected by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
BVRJH1_V04_DF265

21B -126
MR-413-X44-21B000$944.mif
V2
21B
SEQUENTIAL GEARBOX
Diagnostic - Fault finding chart
ALP 1 No dialogue with the sequential gearbox computer
NOTESSpecial notes:
Only consult this customer complaint after a complete check with the diagnostic
tool.
Use the Wiring Diagrams Technical Note for New TWINGO.
Try to establish dialogue with a computer on another vehicle to make sure that the diagnostic tool is not faulty. If
the tool is not causing the fault and dialogue cannot be established with any other computer on the same vehicle,
it may be that a faulty computer is disrupting the CAN diagnostic line.
Use a process of successive disconnections to locate this computer.
Check the voltage of the battery and carry out the operations necessary to obtain a voltage which is to
specification (9.5 V < battery voltage < 17.5 V).
Check the presence of and condition of the Sequential Gearbox fuses on the passenger compartment fuse box
(7.5 A and 20 A).
Check that the computer connector is properly connected and check the condition of its connections.
Check the sequential gearbox earths (good condition, not corroded, tightness of the earth bolt above the
hydraulic unit).
Check that the supply to the computer is correct:
–Earth on the N connections of the 52-track connector.
–+ AVC on connection BP39 of the 52-track connector.
–+ after ignition feed on connection AP4 of the 52-track connector.
Check that the power supply to the diagnostic socket is correct:
–+ AVC on connection BP19.
–Earth on connections MAM and NAM.
If dialogue has still not been established after these checks, contact the Techline.
AFTER REPAIRClear the computer fault memory. Switch off the ignition and wait 20 seconds.
Carry out a road test followed by another check with the diagnostic tool.
BVRJH1_V04_ALP1
MR-413-X44-21B000$944.mif
Vdiag No: 04

21B -136
MR-413-X44-21B000$944.mif
V2
SEQUENTIAL GEARBOX
Diagnostic - Fault finding chart
Vdiag No: 04
21B
ALP 10 Loss of display when driving
NOTESSpecial notes:
Only consult this customer complaint after a complete check with the diagnostic tool.
Check the sequential gearbox supply fuses.
Check all the earths and that the wiring is not damaged.
Check that the connectors have been correctly clipped into the right position.
AFTER REPAIRClear the computer fault memory. Switch off the ignition and wait 20 seconds.
Carry out a road test followed by another check with the diagnostic tool.
BVRJH1_V04_ALP10