wheel RENAULT TWINGO RS 2009 2.G Electrical Equipment Workshop Manual

Contents
82A ENGINE IMMOBILISER
Immobiliser system: List and
location of components 82A-1
Ignition switch: Removal -
Refitting 82A-3
Transponder ring: Removal -
Refitting 82A-6
Battery for remote door
locking control: Removal -
Refitting 82A-8
82B HORN
Audible warning: Removal -
Refitting 82B-1
83A INSTRUMENT PANEL
Instr ument panel: Removal -
Refitting 83A-1
Rev counter: Removal -
Refitting 83A-3
83D CRUISE CONTROL
Cruise control - speed
limiter: List and location of
components 83D-1
Switch: Removal - Refitting 83D-2
Steering wheel switch:
Removal - Refitting 83D-384A CONTROL - SIGNALS
Steering column switch
assembly: List and location
of components 84A-1
Steering column switch
assembly: Removal -
Refitting 84A-2
Screen wiper switch:
Removal - Refitting 84A-6
Signals and lighting switch:
Removal - Refitting 84A-8
Hazard warning lights and
central door control:
Removal - Refitting 84A-10
Lighting dimmer: Removal -
Refitting 84A-12
Exter ior rear view mirror
control switch: Removal -
Refitting 84A-13
Heated rear screen: Repair 84A-14
85A WIPING - WASHING
Wiping and washing: List and
location of components 85A-1
Windscreen wiper blade:
Removal - Refitting 85A-5
Windscreen wiper arm:
Removal - Refitting 85A-6
Windscreen wiper
mechanism: Removal -
Refitting 85A-10
Windscreen wiper motor:
Removal - Refitting 85A-12
Rear screen wiper blade:
Removal - Refitting 85A-16
Rear screen wiper arm:
Removal - Refitting 85A-17
Rear screen wiper motor :
Removal - Refitting 85A-19
Rain and light sensor:
Removal - Refitting 85A-20

80B-5
HEADLIGHTS
Remote headlight beam adjustment motor: Removal - Refitting80B
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aRemove:
-the front wheels (see Wheel: Removal - Refitting)
(MR 411, 35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection),
-the headlights (see 80B, Headlights, Halogen
headlight: Removal - Refitting, page 80B-7) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aTighten the beam adjustment bolt (1) (a maximum of
six turns).
aApply pressure to (2) .
aUnclip the beam adjustment motor by removing the
clip (3) and turning the beam adjustment motor an
eighth of a turn towards the outside of the headlight
(4) .
aUncouple the ball joint (5) from the reflector shell by
tilting the beam adjustment motor slightly.
119379
119380

80B-6
HEADLIGHTS
Remote headlight beam adjustment motor: Removal - Refitting80B
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
a
aKeep the reflector shell towards the rear of the lens
unit while pulling on the bulb holder. (6)
aFit the ball joint (5) into the groove (7) on the headli-
ght.
aRefit the beam adjustment motor, turning it an eighth
of a turn towards the inside of the headlight.
aLoosen the beam adjustment bolt by the same num-
ber of turns as during removal.
II - FINAL OPERATION.
aRefit:
-the front headlights (see 80B, Headlights,
Halogen headlight: Removal - Refitting, page
80B-7) ,
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection),-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),
-the front wheels (see Wheel: Removal - Refitting)
(MR 411, 35A, Wheels and tyres).
aAdjust the headlights (see 80B, Headlights,
Halogen headlight: Adjustment, page 80B-9) . Note:
When refitting a new beam adjustment motor,
tighten the adjusting screws by six turns.
119380
Note:
The ball joint should not just be in contact with
the groove, it should be fitted into it.

80B-7
HEADLIGHTS
Halogen headlight: Removal - Refitting
80B
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aSwitch off the ignition.
aRemove:
-the front wheels (see Wheel: Removal - Refitting)
(MR 411, 35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection).II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove the bolts (1) from the halogen headlight.
aRemove the halogen headlight.
119376
119375

80B-8
HEADLIGHTS
Halogen headlight: Removal - Refitting
80B
aRemove the cover (2) from the halogen headlight.
aDisconnect the halogen headlight connectors.
aRemove:
-the headlight,
-the halogen headlight bulbs (see 80B, Headlights,
Halogen bulb: Removal - Refitting, page 80B-3) .
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit the halogen headlight bulbs (see 80B, Headli-
ghts, Halogen bulb: Removal - Refitting, page
80B-3) .
aConnect the halogen headlight connectors.
aRefit:
-the halogen headlight cover,
-the halogen headlight,
-the halogen headlight bolts.
II - FINAL OPERATION.
aRefit:
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),-the front wheels (see Wheel: Removal - Refitting)
(MR 411, 35A, Wheels and tyres).
aAdjust the halogen headlights (see 80B, Headli-
ghts, Halogen headlight: Adjustment, page 80B-
9) .
119377

80B-9
HEADLIGHTS
Halogen headlight: Adjustment
80B
ADJUSTMENT
I - PREPARATION OPERATION
aPlace the vehicle on a level horizontal working area.
aDo not apply the parking brake.
aCheck and inflate the tyres (see Tyre pressure)
(MR 411, 35A, Wheels and tyres).
aOpen the cover.
aCheck:
-that the luggage compartment is empty,
-that the headlights are clean.
aPosition the headlight beam remote adjustment con-
trol on 0.
aSwitch on the dipped headlights.
II - TEST OPERATION
aPlace a headlight adjustment and checking tool
set to -1% in front of the vehicle (see equipment ins-
tructions).
aCheck the headlight beam adjustment using the
headlight adjustment and checking tool (see the
instructions for the equipment).III - ADJUSTMENT OPERATION
aUsing the headlight adjustment and checking
tool :
-perform lateral adjustment of the headlight using
the screw (1) ,
-adjust the headlight beam by using the screw (2) .
IV - FINAL OPERATION.
aClose the bonnet. Equipment required
headlight adjustment and checking tool
Note:
Do not get into the vehicle throughout the opera-
tion.
119377

80B-10
HEADLIGHTS
Front fog light: Removal - Refitting
80B
REMOVAL
I - REMOVAL PREPARATION OPERATION
Removing the left-hand fog light bulb
a
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove:
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection).Removing the fog light bulb
aRemove:
-the lower bolts (1) of the front wheel arch liner,
-the bolt from the front section of the engine under-
tray on the side concerned.
Removing the fog light
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove:
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection). D4F, and 780
Note:
The front bumper must be removed in order to
remove the left-hand fog light bulb.
K4M, and 854
119264

80B-12
HEADLIGHTS
Front fog light: Removal - Refitting
80B
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
1 - Refitting the fog light bulb
aReplace the fog light bulb with an approved bulb.
aRefit the fog light bulb.
aTurn the fog light bulb a quarter of a turn clockwise.
aConnect the fog light connector.
2 - Refitting the fog light
aRefit the front fog light.
II - FINAL OPERATION.
Refitting the left-hand fog light bulb
aRefit:
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres).
Refitting the fog light bulb
aRefit:
-the lower bolts of the front wheel arch liner,
-the bolt for the front section of the engine undertray
on the side concerned.
Refitting the fog light
aRefit:
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres).
D4F, and 780
K4M, and 854

82A-3
ENGINE IMMOBILISER
Ignition switch: Removal - Refitting
82A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aSet the wheels straight ahead.
aLock the airbag computer using the Diagnostic tool
(see MR 413 Fault finding, 88C, Airbags and pre-
tensioners, Fault finding - Replacement of com-
ponents).
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
aRemove the rev counter (see 83A, Instrument pa-
nel, Rev counter: Removal - Refitting, page 83A-
3) .
aRemove:
-the driver's front airbag (see 88C, Air bag and Pre-
tensioners, Driver's frontal airbag: Removal -
Refitting, page 88C-6)
-the steering wheel ( (see Steering wheel: Remo-
val - Refitting) ),
-the steering column switch assembly (see 84A,
Control - Signals, Steering column switch as-
sembly: Removal - Refitting, page 84A-2) ,
-the antenna/transponder ring (see 82A, Engine
immobiliser, Transponder ring: Removal - Re-
fitting, page 82A-6) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aMake a saw mark on the shear bolt.
aRemove the bolt (1) .
aLoosen the connector at (2) .
aDisconnect the starter switch connector. Equipment required
Diagnostic tool
ENGINE REV COUNTER
119489
119490

82A-4
ENGINE IMMOBILISER
Ignition switch: Removal - Refitting
82A
aPosition the ignition key between the first and se-
cond position (+ accessories and + after ignition
feed) (3) .
aPress the retaining lug (4) .
aRemove the ignition switch.
REFITTING
I - REFITTING PREPARATION OPERATION
aAlways replace:
-the ignition switch bolt,
-the steering wheel bolt.
II - REFITTING OPERATION FOR PART
CONCERNED
aaPosition the ignition key between the first and se-
cond position (+Accessories and +APC) (5) .
aPress the retaining lug (6) .
aFit the ignition switch.
aTighten the shear bolt (7) until the bolt head shears
off.
aConnect the starter switch connector.
aLock the starter switch connector.
108441
Note:
To protect against tampering, always secure the
ignition switch with a shear bolt.
Be sure to recover the sheared-off part of the
bolt after it has been tightened.
108441
119491