RENAULT TWINGO RS 2009 2.G Engine And Peripherals Multimedia Connection Unit User Guide

86D-11V1 MR-413-X44-86D000$020.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – List and location of components86D
BIC
Vdiag No.: 14
For New Twingo
A2 display
A3 display

86D-12V1 MR-413-X44-86D000$030.mif
86D
BIC
Vdiag No.: 14
Role of main components
–Multimedia network interface unit: enables information to be exchanged between the “vehicle” and “multimedia”
multiplex networks.
The multimedia network interface unit is integrated into the display computer on vehicles not equipped with a
navigation system.
If the vehicle is equipped with a navigation system, the multimedia network interface unit is a computer which is
independent of the display: the multimedia connection unit, located behind the glovebox on the passenger side.
The multimedia connection unit (Display or Multimedia connection unit) receives various signals from the vehicle
CAN (speed, status of exterior lights) and retransmits them for the radio via the Multimedia CAN.
The multimedia connection unit (Display or Multimedia connection unit) transmits the activation signal to the radio
and to the other computers participating in the multimedia function when the user switches on the radio or starts the
vehicle.
The multimedia connection unit is involved in the radio anti-theft protection system.
The protection is based on an identifier, the "Vehicle ID", sent on the CAN-V by the instrument panel computer. The
multimedia connection unit reads the "Vehicle ID" on the CAN-V and sends it to the CAN-M for the multimedia type
computers.
The multimedia connection unit allows the optimum configuration of the sound volume according to the vehicle
speed.
–Display: displays various multimedia system data such as the station selected, time, CD listing and satellite
guidance information.
–Radio control satellite: allows the different functions of the multimedia system to be accessed through the radio
control satellite.
–Radio/navigation computer: manages the various multimedia system functions according to user requests and
transmits audio data to the vehicle via the speakers.
MULTIMEDIA CONNECTION UNIT
Fault finding – Role of components

86D-13V1 MR-413-X44-86D000$040.mif
86D
BIC
Vdiag No.: 14
General operation
The multimedia system is involved in the following functions:
–Radio reception (AM, FM).
–Playing CDs/MP3 CDs/navigation map.
–Guidance and navigation system with colour screen.
–Bluetooth hands-free phone.
The use of this multimedia system allows the customer:
–To select radio stations by using the preselections, the list or manual selection.
–To have an automatically-updated radio list.
–To listen to CDs or MP3 CDs.
–To control the radio using the radio control satellite.
–To change various acoustic parameters (bass, treble, fader, etc.).
–To navigate on a colour screen (visual and audio guidance): for this function the system uses GPS, the vehicle
speed wire information and an internal gyroscope.
–To receive traffic information via RDS-TMC and to display it on the navigation map.
–To display the time and temperature on the screen.
–To use the hands-free phone function (sound relayed to the radio speakers) with a Bluetooth phone.
–To be protected by an immobiliser code.
MULTIMEDIA CONNECTION UNIT
Fault finding – Function

86D-14V1 MR-413-X44-86D000$050.mif
86D
BIC
Vdiag No.: 14
CF007: Vehicle configuration (Carry out this configuration only if the vehicle is not equipped with a Navigation
system).
This command is used to configure the computer according to the vehicle equipment.
After having performed CF007, perform CF012 Lighting.
CF008: Radio
This command is used to configure the computer according to the vehicle equipment.
Reread the configuration LC004 Radio in the Read configuration menu to confirm that the change was correctly
accepted.
CF009: Navigation (Only for Clio III).
This command is used to configure the computer according to the Navigation equipment of the vehicle.
Only use this command on a vehicle equipped with navigation.
CF012: Lighting (Carry out this configuration only if the vehicle is not equipped with a Navigation system)
This command, on New Twingo, is used to configure the luminosity level of the display screen by selecting the type
of radio.
This command, on Clio III, is used to configure the luminosity level of the display screen by selecting the type of
radio, and to confirm the option with or without dimmer.
NOTE: The two types of radio can be distinguished as follows: radio R02 has a telephone button, radio R01 does
not.
MULTIMEDIA CONNECTION UNIT
Fault finding – Configurations

86D-15V1 MR-413-X44-86D000$060.mif
86D
BIC
Vdiag No.: 14
VP001: "Write VIN"
This command permits manual entry of the vehicle's VIN into the computer. Use this command each time the
computer is replaced. The VIN number is inscribed on the manufacturer's plate.
Procedure for writing the VIN
–Establish dialogue with the computer of the multimedia connection unit
–Select the Repair mode menu.
–Select the Other parameters menu.
–Select line VP001 Write VIN.
–Enter the VIN.
–Exit fault finding mode.
–Switch off the ignition.
–Wait 5 seconds.
–Reread the VIN in the Identification menu for confirmation (ID008 VIN code).
SC002: Vehicle identifier (Only for New Twingo)
This command is used to obtain the vehicle identifier. The SC002 is used to read the "Vehicle ID" entered in the
instrument panel computer and to enter it in the multimedia connection unit and in the display. The vehicle identifier
is contained in this "Vehicle ID".
This command is to be used each time the computer is replaced. The radio will be locked if it does not read a correct
vehicle identifier.
MULTIMEDIA CONNECTION UNIT
Fault finding – Programming

86D-16V1 MR-413-X44-86D000$070.mif
86D
BIC
Vdiag No.: 14
For information on removing and refitting the multimedia connection unit of the multimedia network, refer to the
repair manual for the vehicle concerned:
If the vehicle is equipped with a Navigation computer (Only on Clio III):
See MR 392, Mechanical, 83C, On-board telematics system, Multimedia network interface unit: Removal -
Refitting.
If the vehicle is not equipped with a Navigation computer:
Clio III: See MR 392, Mechanical, 86A, Radio, Display: Removal - Refitting.
New Twingo: See MR 411, Mechanical, 86A, Radio, Display: Removal - Refitting.
Operations to be carried out before replacing the multimedia network interface unit:
1- Before replacing the multimedia connection unit (with Techline approval), read the faults and carry out a
conformity check to check that it is actually defective.
2-After obtaining Techline approval, remove the multimedia connection unit, with the ignition off (wait 1 minute for
the system to shut down completely).
The multimedia network interface units available from the Parts Department are supplied unconfigured.
Operations to be carried out after replacing the multimedia connection unit:
–Connect the diagnostic tool and switch on the system, then establish dialogue with the computer.
–Configure the multimedia connection unit (see Configurations and Programming).
–Configure the computer using command CF007 Vehicle configuration, then perform CF012 Lighting. Only carry
out these configurations on vehicles not equipped with a Navigation system. (see Configurations).
–If a radio is present, configure the computer using command CF008 Radio (see Configurations).
–If a Navigation system is present, configure the computer using command CF009 Navigation (see
Configurations).
–Enter the VIN code using command VP001 Write VIN (see Programming).
–Check that there are no faults and that the multimedia system is operating correctly. Note:
If the radio and the multimedia connection unit (BIC) are replaced simultaneously, the multimedia
connection unit must be configured first (see Configurations and Programming).
MULTIMEDIA CONNECTION UNIT
Fault finding – Replacement of components

86D-17V1 MR-413-X44-86D000$080.mif
86D
BIC
Vdiag No.: 14
Tool faultAssociated
DTCDiagnostic tool title
DF0019341Computer configuration
DF0029344Computer
DF00393E3Screen
DF0059303Supply
DF0069309Activation signal
DF007934CComputer
DF008934DComputer
DF0119331External temperature sensor circuit
MULTIMEDIA CONNECTION UNIT
Fault finding – Fault summary table

86D-18
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86D000$090.mif
86D
BIC
Vdiag No.: 14
DF001
PRESENT
OR
STOREDCOMPUTER CONFIGURATION
1.DEF: Blank or incomplete configuration
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after the multimedia system has been switched on.
Configure the system (see Configurations and programming).
If the fault is still present, contact your Techline.
BIC_V14_DF001
MULTIMEDIA CONNECTION UNIT
Fault finding – Interpretation of faults

86D-19
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86D000$090.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Interpretation of faults86D
BIC
Vdiag No.: 14
DF002
PRESENT
OR
STOREDCOMPUTER
1.DEF: Internal electronic fault
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after the multimedia system has been switched on.
If the vehicle is equipped with a Navigation computer (only on Clio III), replace the multimedia connection unit (see
MR 392, Mechanical, 83C, On-board telematics system, Multimedia network interface unit: Removal -
Refitting).
If the vehicle is not equipped with a Navigation computer, replace the display (see MR 392 (Clio III) or MR 411
(New Twingo), Mechanical, 86A, Radio, Display: Removal - Refitting).
If the fault is still present, contact your Techline.
BIC_V14_DF002

86D-20
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86D000$090.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Interpretation of faults86D
BIC
Vdiag No.: 14
DF003
PRESENT
OR
STOREDSCREEN
DEF: No communication with display
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after the multimedia system has been switched on.
If the fault is present, the display does not operate.
If the vehicle is equipped with a Navigation computer (only on Clio III), replace the multimedia connection unit (see
MR 392, Mechanical, 83C, On-board telematics system, Multimedia network interface unit: Removal -
Refitting).
If the vehicle is not equipped with a Navigation computer, replace the display (see MR 392 (Clio III) or MR 411
(New Twingo), Mechanical, 86A, Radio, Display: Removal - Refitting).
If the fault persists, contact your Techline.
BIC_V14_DF003