weight SAAB 9-2X 2006 Owner's Manual

Maintenance and service
11 - 3 5
11
– CONTINUED –
NOTEWhen any of the wheels is removed
and replaced for tire rotation or to
change a flat tire, always check the
tightness of the wheel nuts after driv-
ing approximately 600 miles (1,000
km). If any nut is loose, tighten it to the
specified torque.
Aluminum wheelsAluminum wheels can be scratched and
damaged easily. Handle them carefully to
maintain their appearance, performance,
and safety.

When any of the wheels is removed and
replaced for tire rotation or to change a
flat, always check the tightness of the
wheel nuts after driving approximately 600
miles (1,000 km). If any nut is loose, tight-
en it to the specified torque.

Never apply oil to the threaded parts,
wheel nuts, or tapered surface of the
wheel.

Never let the wheel rub against sharp
protrusions or curbs.

Be sure to fit tire chains on uniformly
and completely around the tire, otherwise
the chains may scratch the wheel.

When wheel nuts, balance weights, or
the center cap is replaced, be sure to re-
place them with genuine Saab parts de-
signed for aluminum wheels.
Windshield washer fluidIf you spray washer fluid on the windshield
but the supply of washer fluid appears to
diminish, check the level of washer fluid in
the tank. Use only those wheels that are
specified for your vehicle. Wheels
not meeting specifications could in-
terfere with brake caliper operation
and may cause the tires to rub
against the wheel well housing dur-
ing turns. The resulting loss of vehi-
cle control could lead to an acci-
dent.
300523
A1910BE-A-GSAAB.book Page 35 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Consumer information and Reporting safety defects
13-3
13
– CONTINUED –
which specifies the maximum load a
tire can carry at the speed indicated
by its speed symbol, at maximum in-
flation pressure.
For example, “91” means 1,356 lbs
(615 kg), “89” means 1,279 lbs (580
kg)(7) Speed Rating: An alphabetical
system describing a tire’s capability to
travel at established and predeter-
mined speeds.
For example, “V” means 149 mph
(240 km/h), “W” means 168 mph (270
km/h)


Tire Identification Number (TIN)
Tire Identification Number (TIN) is
marked on the intended outboard
sidewall. The TIN is composed of four
groups. Here is a brief review of the
TIN with a breakdown of its individual
elements.(1) Manufacturer’s Identification Mark
(2) Tire Size
(3) Tire Type Code
(4) Date of Manufacture
The first two figures identify the week,
starting with “01” to represent the first
full week of the calendar year; the
second two figures represent the
year. For example, 0101 means the
1st week of 2001.


Other markings
The following makings are also
placed on the sidewall.

Maximum permissible inflation
pressure
The maximum cold inflation pressure
to which this tire may be inflated. For
example, "300 kpa (44 PSI) MAX.
PRESS"

Maximum load rating
The load rating at the maximum per-
missible weight load for this tire. For
example, “MAX. LOAD 580 kg (1279
LBS) @ 300 kpa (44 PSI) MAX.
PRESS.” Load indices apply only to the
tire, not to the vehicle. Putting a
load rated tire on any vehicle
does not mean the vehicle can
be loaded up to the tire’s rated
load.

Speed ratings apply only to
the tire, not to the vehicle. Put-
ting a speed rated tire on any
vehicle does not mean the ve-
hicle can be operated at the
tire’s rated speed.
The speed rating is void if the
tires are worn out, damaged,
repaired, retreaded, or other-
wise altered from their original
condition. If tires are repaired,
retreaded, or otherwise al-
tered, they may not be suitable
for original equipment tire de-
signed loads and speeds.
DOT XX XX XXX XXXX
(1) (2)
(3)(4)
A1910BE-A-GSAAB.book Page 3 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

13-6
Consumer information and Reporting safety defects


Vehicle label
The vehicle label is affixed to the driv-
er’s side B-pillar (US).
On Canadian vehicles this label is lo-
cated inside the glovebox.Example:
The vehicle label shows original tire
size, recommended cold tire inflation
pressure on each tire at maximum
loaded vehicle weight, seating capac-
ity and loading information.


Adverse safety consequences
of under-inflation
Driving at high speeds with exces-
sively low tire pressures can cause
the tires to flex severely and to rapidly
become hot. A sharp increase in tem-
perature could cause tread separa-
tion, and failure of the tire(s). Possible
resulting loss of vehicle control could
lead to an accident.


Measuring and adjusting air
pressure to achieve proper infla-
tion
Check and, if necessary, adjust the
pressure of each tire (including the
spare) at least once a month and be-
fore any long journey. Check the tire
pressures when the tires are cold.
Use a pressure gauge to adjust the
tire pressures to the specific values.
Driving even a short distance warms
up the tires and increases the tire
pressures. Also, the tire pressures
are affected by the outside tempera-
ture. It is best to check tire pressure
outdoors before driving the vehicle.
When a tire becomes warm, the air in-
side it expands, causing the tire pres-
sure to increase. Be careful not to
mistakenly release air from a warm
tire to reduce its pressure.

Glossary of tire terminology
Cold tire pressure
The pressure in a tire that has been
driven less than 1 mile or has been
standing for three hours or more.
D00120
MD
TIRE AND LOADING INFORMATIONSEATING CAPACITY : TOTAL 5
ORIGINAL TIRE SIZESEE OWNER’S MANUAL FOR
ADDITIONAL INFORMATION
COLD TIRE
INFLATION PRESSRE
COLD TIRE
INFLATION PRESSREFRONT
REAR
220kPa,32PSI
200kPa,29PSI
P205/55R16
T135/70D16
420kPa, 60PSI
COMPACT SPARE TIREThe combined weight of occupants andcargo should never exceed 408kg or 900lbs.
FRONT 2 : REAR 3
D00116
A1910BE-A-GSAAB.book Page 6 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Consumer information and Reporting safety defects
13-7
13
– CONTINUED –

Maximum inflation pressure
The maximum cold inflation pressure
to which a tire may be inflated.
Recommended inflation pres-
sure
The cold inflation pressure recom-
mended by a vehicle manufacturer.
Intended outboard sidewall
1)The sidewall that contains a
whitewall, bears white lettering or
bears manufacturer, brand, and/or
model name molding that is higher
or deeper than the same molding
on the other sidewall of the tire, or
2)The outward facing sidewall of an
asymmetrical tire that has a particu-
lar side that must always face out-
ward when mounting on a vehicle.
Accessory weight
The combined weight (in excess of
those standard items which may be
replaced) of floor mats, leather seats
and cross bars to the extent that these
items are available as factory-in-
stalled equipment (whether installed
or not).
Curb weight
The weight of a motor vehicle with
standard equipment including themaximum capacity of fuel, oil, and
coolant and air conditioning.

Maximum loaded vehicle weight
The sum of curb weight, accessory
weight, vehicle capacity weight and
production options weight.
Normal occupant weight
150 lbs (68 kg) times the number of
occupants (3 occupants).
Occupant distribution
Distribution of occupants in a vehicle,
2 in front, 1 in rear seat.
Production options weight
The combined weight of those in-
stalled regular production options
weighing over 5.1 lbs (2.3 kg) in ex-
cess of those standards items which
they replace, not previously consid-
ered in curb weight or accessory
weight.
Vehicle capacity weight
The total weight of cargo, luggage
and occupants that can be added to
the vehicle.
Vehicle maximum load on a tire
Load on an individual tire that is deter-
mined by distributing to each axle its
share of the maximum loaded vehicle
weight and dividing by two.

Vehicle normal load on a tire
Load on an individual tire that is deter-
mined by distributing to each axle its
share of the curb weight, accessory
weight, and normal occupant weight
and dividing by two.
Tire care – maintenance and
safety practices
Check on a daily basis that the tires
are free from serious damage, nails,
and stones. At the same time, check
the tires for abnormal wear.
Inspect the tire tread regularly and
replace the tires before their tread
wear indicators become visible. When
a tire’s tread wear indicator becomes
visible, the tire is worn beyond the ac-
ceptable limit and must be replaced
immediately. With a tire in this condi-
tion, driving at even low speeds in wet
weather can cause the vehicle to hy-
droplane. Possible resulting loss of
vehicle control can lead to an acci-
dent.
To maximize the life of each tire and
ensure that the tires wear uniformly, it
is best to rotate the tires every 7,500
miles (12,500 km). Rotating the tires
A1910BE-A-GSAAB.book Page 7 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

13-8
Consumer information and Reporting safety defects
involves switching the front and rear
tires on the right-hand side of the ve-
hicle and similarly switching the front
and rear tires on the left-hand side of
the vehicle. (Each tire must be kept on
its original side of the vehicle.) Re-
place any damaged or unevenly worn
tire at the time of rotation. After tire ro-
tation, adjust the tire pressures and
make sure the wheel nuts are correct-
ly tightened. A tightening torque spec-
ification and a tightening sequence
specification for the wheel nuts can be
found “Flat tires” section in chapter
9.

Vehicle load limit – how to de-
termineThe load capacity of your vehicle is
determined by weight, not by avail-
able cargo space. The load limit of
your vehicle is shown on the vehicle
label attached to the driver’s side B-
pillar. Locate the statement “The com-
bined weight of occupants and cargo
should never exceed XXX kg or XXX
lbs” on your vehicle’s label.
The vehicle label also shows seating
capacity of your vehicle.
The total load capacity includes thetotal weight of driver and all passen-
gers and their belongings, any cargo,
any optional equipment such as a
trailer hitch, roof rack or bike carrier,
etc., and the tongue load of a trailer.
Therefore cargo capacity can be cal-
culated by the following method.
Cargo capacity = Load limit – (total
weight of occupants + total weight of
optional equipment + tongue load of a
trailer (if applicable))
For towing capacity information and
weight limits, refer to “Trailer towing”
section in chapter 8.


Calculating total and load capac-
ities varying seating configura-
tions
Calculate the available load capacity
as shown in the following examples:Example 1A
Vehicle capacity weight of the vehicle
is 900 lbs (408 kg), which is indicated
on the vehicle label with the statement
“The combined weight of occupants
and cargo should never exceed 900
lbs or 408 kg”.
For example, if the vehicle has one
occupant weighing 154 lbs (70 kg)
plus cargo weighing 662 lbs (300 kg).
1. Calculate the total weight.
D00121
A1910BE-A-GSAAB.book Page 8 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Consumer information and Reporting safety defects
13-9
13
– CONTINUED –
2. Calculate the available load capac-
ity by subtracting the total weight from
the vehicle capacity weight of 900 lbs
(408 kg).
3. The result of step 2 shows that a
further 84 lbs (38 kg) of cargo can be
carried.Example 1B
For example, if a person weighing 176
lbs (80 kg) now enters the same vehi-
cle (bringing the number of occupants
to two), the calculations are as fol-
lows:
1. Calculate the total weight.2. Calculate the available load capac-
ity.
3. The total weight now exceeds the
capacity weight by 92 lbs (42 kg), so
the cargo weight must be reduced by
92 lbs (42 kg) or more.
Example 2A
Vehicle capacity weight of the vehicle
is 900 lbs (408 kg), which is indicatedTotal weight
= 154 lbs (70 kg) + 662 lbs (300 kg)
= 816 lbs (370 kg)(Occupant) (Cargo)
800272
Total weight
= 154 lbs (70 kg) + 176 lbs (80 kg)
+ 662 lbs (300 kg)
= 992 lbs (450 kg)(Occupant)
(Cargo)
D00122
A1910BE-A-GSAAB.book Page 9 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

13-10
Consumer information and Reporting safety defects
on the vehicle label with the statement
“The combined weight of occupants
and cargo should never exceed 408
kg or 900 lbs”.
For example, the vehicle has one oc-
cupant weighing 165 lbs (75 kg) plus
cargo weighing 375 lbs (170 kg). In
addition, the vehicle is fitted with a
trailer hitch weighing 22 lbs (10 kg), to
which is attached a trailer weighing
1,764 lbs (800 kg). 10% of the trailer
weight is applied to the trailer tongue
(i.e. Tongue load = 176 lbs (80 kg)).
1. Calculate the total weight.
2. Calculate the available load capac-
ity.3. The result of step 2 shows that a
further 162 lbs (73 kg) of cargo can be
carried.
Example 2B
For example, if a person weighing 143
lbs (65 kg) and a child weighing 40 lbs
(18 kg) now enter the same vehicle
(bringing the number of occupants to
three), and a child restraint system
weighing 11 lbs (5 kg) is installed inthe vehicle for the child to use, the cal-
culations are as follows:
1. Calculate the total weight.
2. Calculate the available load capac-
ity.
3. The total weight now exceeds theTotal weight
= 165 lbs (75 kg) + 375 lbs (170 kg)
+ 22 lbs (10 kg) + 176 lbs (80 kg)
= 738 lbs (335 kg)(Occupant) (Cargo)
(Trailer hitch)(Tongue load)
D00123
Total weight
= 165 lbs (75 kg) + 143 lbs (65 kg)
+ 40 lbs (18 kg)
+ 11 lbs (5 kg) + 375 lbs (170 kg)
+ 22 lbs (10 kg) + 176 lbs (80 kg)
= 932 lbs (423 kg)(Occupant)
(Cargo)
(Trailer hitch) (Child restraint)
(Tongue load) (Occupant)
A1910BE-A-GSAAB.book Page 10 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Consumer information and Reporting safety defects
13-11
13
– CONTINUED –
capacity weight by 32 lbs (15 kg), so
the cargo weight must be reduced by
32 lbs (15 kg) or more.
Determining compatibility of
tire and vehicle load capaci-
tiesThe sum of four tires’ maximum load
ratings must exceed the maximum
loaded vehicle weight (“GVWR”). In
addition, sum of the maximum load
ratings of two front tires and of two
rear tires must exceed each axle’s
maximum loaded capacity (“GAWR”).
Original equipment tires are designed
to fulfill those conditions.
The maximum loaded vehicle weight
is referred to Gross Vehicle Weight
Rating (GVWR). And each axle’s
maximum loaded capacity is referred
to Gross Axle Weight Rating
(GAWR). The GVWR and each axle’s
GAWR are shown on the vehicle cer-
tification label affixed to the driver’s
door.
The GVWR and front and rear
GAWRs are determined by not only
the maximum load rating of tires but
also loaded capacities of the vehicle’ssuspension, axles and other parts of
the body.
Therefore, this means that the vehicle
cannot necessarily be loaded up to
the tire’s maximum load rating on the
tire sidewall.

Adverse safety consequenc-
es of overloading on handling
and stopping and on tiresOverloading could affect vehicle han-
dling, stopping distance, vehicle and
tire as shown in the following. This
could lead to an accident and possibly
result in severe personal injury.
Vehicle stability will deteriorate.
Heavy and/or high-mounted loads
could increase the risk of rollover.
Stopping distance will increase.
Brakes could overheat and fail.
Suspension, bearings, axles and
other parts of the body could break or
experience accelerated wear that will
shorten vehicle life.
Tires could fail.
Tread separation could occur.
Tire could separate from its rim.

Steps for Determining Cor-
rect Load Limit1. Locate the statement “The com-
bined weight of occupants and cargo
should never exceed XXX pounds” on
your vehicle’s label.
2. Determine the combined weight of
the driver and passengers that will be
riding in your vehicle.
3. Subtract the combined weight of
the driver and passengers from XXX
kilograms or XXX pounds.
4. The resulting figure equals the
available amount of cargo and lug-
gage load capacity. For example, if
the “XXX” amount equals 1,400 lbs
(635 kg) and there will be five- 150 lbs
(68 kg) passengers in your vehicle,
the amount of available cargo and
luggage load capacity is 650 lbs.
(1,400 – 750 (5  150) = 650 lbs.)
5. Determine the combined weight of
luggage and cargo being loaded on
the vehicle. That weight may not safe-
ly exceed the available cargo and lug-
gage load capacity calculated in Step
4.
6. If your vehicle will be towing a trail-
er, load from your trailer will be trans-
A1910BE-A-GSAAB.book Page 11 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

14-4
Index
Electronic Brake Force Distribution (EBD) system ........... 7-18
Emergency Locking Retractor (ELR) ................................ 1-10
Engine
Compartment overview ................................................. 11-6
Coolant ....................................................................... 11-13
Exhaust gas (Carbon monoxide) ............................... 6, 8-2
Hood ............................................................................. 11-4
Oil ................................................................................. 11-8
Overheating ................................................................. 9-10
Starting .......................................................................... 7-6
Stopping ........................................................................ 7-8
Exterior care ..................................................................... 10-2
F
Flat tires ............................................................................. 9-4
Floor mat ............................................................................ 6-8
Fluid level
Automatic transmission .............................................. 11-20
Brake .......................................................................... 11-25
Clutch ......................................................................... 11-26
Power steering ............................................................ 11-24
Folding down the rear seat ................................................. 1-7
Front
Differential gear oil ...................................................... 11-22
Fog light button ............................................................ 3-19
Seatbelt pretensioners ................................................. 1-19
Seats ............................................................................. 1-2
Turn signal light .......................................................... 11-49
Fuel .................................................................................... 7-2
Economy hints ............................................................... 8-2
Filler lid and cap ............................................................ 7-3
Gauge ............................................................................ 3-7
Requirements ................................................................ 7-2Fuses .............................................................................. 11-41
Fuses and circuits ............................................................. 12-6
G
GAWR (Gross Axle Weight Rating) .................................. 8-11
Glove box ........................................................................... 6-4
GVWR (Gross Vehicle Weight Rating) ............................. 8-11
H
Hazard warning flasher ....................................................... 3-6
Head restraint adjustment ........................................... 1-4, 1-6
Headlight beam leveler ..................................................... 3-18
Headlight flasher ............................................................... 3-16
Headlights .............................................................. 3-16, 11-46
Heater operation ................................................................. 4-5
High beam indicator light .................................................. 3-14
Horn .................................................................................. 3-26
Hose and connections .................................................... 11-12
I
Ignition switch ..................................................................... 3-3
Illuminated entry ................................................................. 2-8
Illumination brightness control .......................................... 3-18
Immobilizer ......................................................................... 2-3
Indicator light
High beam ................................................................... 3-14
Selector lever position ................................................. 3-14
Turn signal ................................................................... 3-14
Inside mirror ...................................................................... 3-24
Interior light ......................................................................... 6-2A1910BE-A-GSAAB.book Page 4 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Index
14-7
14
Speedometer ...................................................................... 3-6
SRS airbag (Supplemental Restraint System airbag) .. 4, 1-33
SRS airbag system monitors ............................................ 1-53
SRS airbag system servicing ............................................ 1-54
SRS airbag system warning light ...................................... 3-10
SRS side airbag ............................................................... 1-48
Starting the engine .............................................................. 7-6
State emission testing (U.S. only) ....................................... 7-5
Stopping the engine ............................................................ 7-8
Storage compartments ....................................................... 6-4
Sun shades ...................................................................... 2-22
Sun visors ........................................................................... 6-3
Moonroof ................................................................. 2-21, 9-14
Supplemental Restraint System airbag (SRS) ............. 4, 1-33
Synthetic leather upholstery ............................................. 10-5
T
Tachometer ......................................................................... 3-7
Temperature gauge ............................................................ 3-8
Temporary spare tire ........................................................... 9-2
Tie-down hooks ................................................................ 9-11
Tilt steering wheel ............................................................. 3-26
Tire
Chains ........................................................................... 8-9
Inspection .................................................................. 11-30
Pressures and wear ................................................... 11-31
Replacement ............................................................. 11-33
Rotation ..................................................................... 11-33
Tires .................................................................................. 12-4
Types ......................................................................... 11-30
Tires and wheels ............................................................ 11-30
Top tether anchorages ...................................................... 1-31Towing ............................................................................... 9-10
All wheels on the ground .............................................. 9-12
Flat-bed truck ............................................................... 9-12
Trailer
Hitches ......................................................................... 8-16
Towing .......................................................................... 8-13
Towing tips ................................................................... 8-18
Turn signal
Indicator lights .............................................................. 3-14
Lever ............................................................................ 3-17
V
Valet mode ........................................................................ 2-15
Vanity mirror ........................................................................ 6-3
Vehicle
Capacity weight ............................................................ 8-11
Identification ............................................................... 12-10
Symbols ............................................................................ 3
Ventilation ........................................................................... 4-2
W
Warning and indicator lights ................................................ 3-9
Warning lights
ABS .............................................................................. 3-12
All-Wheel Drive ............................................................ 3-14
Anti-lock Brake System ................................................ 3-12
AT OIL TEMPerature .................................................... 3-12
Brake system ............................................................... 3-13
Charge ......................................................................... 3-11
CHECK ENGINE .......................................................... 3-11
Door open .................................................................... 3-13
A1910BE-A-GSAAB.book Page 7 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com