fuse SATURN AURA 2007 Owners Manual

Front Seats
Manual Seats
{CAUTION:
You can lose control of the vehicle if you
try to adjust a manual driver’s seat while
the vehicle is moving. The sudden
movement could startle and confuse you,
or make you push a pedal when you do
not want to. Adjust the driver’s seat only
when the vehicle is not moving.To move a manual seat forward or rearward:
1. Lift the bar to unlock
the seat.
2. Slide the seat to the
desired position and
release the bar.
Try to move the seat with your body to be sure
the seat is locked in place.
8
ProCarManuals.com

Reclining Seatbacks
Manual Reclining Seatbacks
{CAUTION:
You can lose control of the vehicle if you
try to adjust a manual driver’s seat while
the vehicle is moving. The sudden
movement could startle and confuse you,
or make you push a pedal when you do
not want to. Adjust the driver’s seat only
when the vehicle is not moving.
{CAUTION:
If the seatback is not locked, it could
move forward in a sudden stop or crash.
That could cause injury to the person
sitting there. Always push and pull on the
seatback to be sure it is locked.
On seats with manual reclining seatbacks, the
lever used to operate them is located on the
outboard side of the seat.
10
ProCarManuals.com

If the engine still does not start, and the key
appears to be not damaged, try another ignition
key. At this time, you may also want to check the
fuse, seeFuses on page 343. If the engine still
does not start with the other key, your vehicle
needs service. If your vehicle does start, the rst
key may be faulty. See your dealer/retailer
who can service the PASS-Key
®III+ to have a
new key made. In an emergency, contact
Roadside Assistance. SeeRoadside Assistance
Program on page 377.
It may be possible for the PASS-Key
®III+ decoder
to “learn” the transponder value of a new or
replacement key. Up to 10 keys may be
programmed for the vehicle. The following
procedure is for programming additional keys only.
If your vehicle was rst sold in Canada, or if all
the currently programmed keys are lost or do not
operate, you must see your dealer/retailer or a
locksmith who can service PASS-Key
®III+ to have
keys made and programmed to the system.
See your dealer/retailer or a locksmith who can
service PASS-Key
®III+ to get a new key blank that
is cut exactly as the ignition key that operates
the system.To program the new key:
1. Verify that the new key has a
1stamped on it.
2. Insert the already programmed key in the
ignition and start the engine. If the engine will
not start, see your dealer/retailer for service.
3. After the engine has started, turn the key to
OFF, and remove the key.
4. Insert the key to be programmed and turn it to
the ON position within ve seconds of the
original key being turned to the OFF position.
The security light will turn off once the key
has been programmed.
5. Repeat Steps 1 through 4 if additional keys
are to be programmed.
If you are ever driving and the security light comes
on and stays on, you may be able to restart
your engine if you turn it off. Your PASS-Key
®III+
system, however, is not working properly and
must be serviced by your dealer/retailer.
Your vehicle is not protected by the
PASS-Key
®III+ system at this time.
If you lose or damage your PASS-Key®III+ key,
see your dealer/retailer or a locksmith who can
service PASS-Key
®III+ to have a new key made.
Do not leave the key or device that disarms or
deactivates the theft deterrent system in the
vehicle.
106
ProCarManuals.com

Turn and Lane-Change Signals
The turn signal has two upward (for right) and two
downward (for left) positions. These positions
let you signal a turn or a lane change.
To signal a turn, move the lever all the way up or
down. When the turn is nished, the lever
returns automatically to the normal position.
An arrow on the
instrument panel cluster
ashes in the direction of
the turn or lane change.
To signal a lane change, raise or lower the lever
until the arrow starts to ash. Hold it there until you
complete your lane change. The lever returns
by itself when it is released.
If the arrows ash rapidly or do not go on at all as
you signal a turn or lane change, a signal bulb
could be burned out and other drivers will not see
your turn signal.
Replace burned out bulbs to help avoid an
accident. Also, check the appropriate fuses. See
Fuses on page 343.
Headlamp High/Low-Beam Changer
To change the headlamps from low beam to
high beam, push the turn signal/multifunction lever
toward the front of the vehicle.
This light on the
instrument panel cluster
comes on if the high
beam lamps are turned
on while the ignition
is on.
To change the headlamps from high beam to low
beam, pull the turn signal lever toward the rear
of the vehicle.
Flash-to-Pass
This feature lets you use your high-beam
headlamps to signal a driver in front of you that
you want to pass.
To use it, pull the turn signal/multifunction lever
toward you until the high-beam headlamps
come on, then release the lever to turn them off.
142
ProCarManuals.com

Accessory Power Outlet(s)
Accessory power outlets can be used to connect
auxiliary electrical equipment such as a cellular
telephone or CB radio.
There are two accessory power outlets. One
accessory power outlet is inside the center storage
console and the other is located on the center
storage console below the climate controls.
To use an outlet, lift the protective cap. When not
in use, always cover the outlet with the protective
cap. The accessory power outlet is operational
at all times.
Notice:Leaving electrical equipment plugged
in for an extended period of time while the
vehicle is off will drain the battery. Power is
always supplied to the outlets. Always unplug
electrical equipment when not in use and
do not plug in equipment that exceeds
the maximum 20 ampere rating.Certain electrical accessories may not be
compatible with the accessory power outlet and
could result in blown vehicle or adapter fuses.
If you experience a problem, see your retailer for
additional information on the accessory power
outlet.
Notice:Adding any electrical equipment to
your vehicle can damage it or keep other
components from working as they should. The
repairs would not be covered by your
warranty. Do not use equipment exceeding
maximum amperage rating of 20 amperes.
Check with your dealer/retailer before adding
electrical equipment.
When adding electrical equipment, be sure to
follow the proper installation instructions included
with the equipment.
Notice:Improper use of the power outlet can
cause damage not covered by your warranty.
Do not hang any type of accessory or
accessory bracket from the plug because the
power outlets are designed for accessory
power plugs only.
153
ProCarManuals.com

4. To prevent the battery from draining while the
vehicle is being towed, remove the following
fuse from the instrument panel fuse block:
(IGN SENSOR). SeeInstrument Panel Fuse
Block on page 343for more information.
5. Turn the ignition key to ACC.
6. Shift your transmission to NEUTRAL (N).
7. Release the parking brake.
Remember to reinstall the IGN SENSOR fuse
once you have reached your destination.
Notice:If you exceed 65 mph (105 km/h) while
towing your vehicle, it could be damaged.
Never exceed 65 mph (105 km/h) while towing
your vehicle.Notice:Towing your vehicle from the rear
could damage it. Also, repairs would not
be covered by the warranty. Never have your
vehicle towed from the rear.
249
ProCarManuals.com

Wheel Replacement.................................. 316
Tire Chains............................................... 319
If a Tire Goes Flat.................................... 319
Tire Inator Kit.......................................... 320
Appearance Care........................................ 332
Cleaning the Inside of Your Vehicle.......... 332
Fabric/Carpet............................................. 333
Instrument Panel, Vinyl, and Other Plastic
Surfaces................................................ 334
Care of Safety Belts.................................. 335
Weatherstrips............................................ 335
Washing Your Vehicle............................... 335
Cleaning Exterior Lamps/Lenses................ 336
Finish Care............................................... 336
Windshield and Wiper Blades.................... 337
Aluminum Wheels...................................... 337
Tires......................................................... 338
Sheet Metal Damage................................. 338Finish Damage.......................................... 339
Underbody Maintenance............................ 339
Chemical Paint Spotting............................ 339
Vehicle Care/Appearance Materials............ 340
Vehicle Identication.................................. 341
Vehicle Identication Number (VIN)........... 341
Service Parts Identication Label............... 341
Electrical System........................................ 342
Add-On Electrical Equipment..................... 342
Windshield Wiper Fuses............................ 342
Power Windows and Other Power
Options.................................................. 342
Fuses........................................................ 343
Instrument Panel Fuse Block..................... 343
Engine Compartment Fuse Block............... 346
Rear Compartment Fuse Block.................. 348
Capacities and Specications.................... 351
Section 5 Service and Appearance Care
252
ProCarManuals.com

California Proposition 65 Warning
Most motor vehicles, including this one, contain
and/or emit chemicals known to the State of
California to cause cancer and birth defects or
other reproductive harm. Engine exhaust,
many parts and systems (including some inside
the vehicle), many uids, and some component
wear by-products contain and/or emit these
chemicals.
Doing Your Own Service Work
{CAUTION:
Never try to do your own service on
hybrid components. You can be injured
and your vehicle can be damaged if you
try to do your own service work. Service
and repair of these hybrid components
should only be performed by a
Saturn-trained service technician with the
proper knowledge and tools.
{CAUTION:
You can be injured and your vehicle could
be damaged if you try to do service work
on a vehicle without knowing enough
about it.
Be sure you have sufficient knowledge,
experience, the proper replacement
parts, and tools before you attempt any
vehicle maintenance task.
Be sure to use the proper nuts, bolts,
and other fasteners. English and metric
fasteners can be easily confused. If you
use the wrong fasteners, parts can later
break or fall off. You could be hurt.
254
ProCarManuals.com

A. Engine Air Cleaner/Filter. SeeEngine Air
Cleaner/Filter on page 270.
B. Cooling Fans. SeeCooling System on
page 278.
C. Engine Oil Dipstick. See “Checking Engine Oil”
underEngine Oil on page 265.
D. Engine Oil Fill Cap. See “When to Add Engine
Oil” underEngine Oil on page 265.
E. Engine Coolant Surge Tank. SeeEngine
Coolant on page 272.
F. Brake Master Cylinder Reservoir. See″Brake
Fluid″underBrakes on page 284.
G. Battery. SeeBattery on page 287
H. Engine Compartment Fuse Block. SeeEngine
Compartment Fuse Block on page 346.
I. Windshield Washer Fluid Reservoir. See
“Adding Washer Fluid” underWindshield
Washer Fluid on page 282.Engine Oil
Checking Engine Oil
It is a good idea to check the engine oil every time
you get fuel. In order to get an accurate reading,
the oil must be warm and the vehicle must be
on level ground.
The engine oil dipstick handle is a yellow loop.
SeeEngine Compartment Overview on page 264
for the location of the engine oil dipstick.
1. Turn off the engine and give the oil several
minutes to drain back into the oil pan. If you
do not do this, the oil dipstick might not
show the actual level.
2. Pull out the dipstick and clean it with a paper
towel or cloth, then push it back in all the
way. Remove it again, keeping the tip down,
and check the level.
265
ProCarManuals.com

Electrical System
Add-On Electrical Equipment
Notice:Do not add anything electrical to your
vehicle unless you check with your retailer
rst. Some electrical equipment can damage
your vehicle and the damage would not
be covered by your warranty. Some add-on
electrical equipment can keep other
components from working as they should.
Your vehicle has an airbag system. Before
attempting to add anything electrical to your
vehicle, seeServicing Your Airbag-Equipped
Vehicle on page 82.
Windshield Wiper Fuses
The windshield wiper motor is protected by an
internal circuit breaker and a fuse. If the motor
overheats due to heavy snow, etc., the wiper will
stop until the motor cools. If the overload is
caused by some electrical problem, have it xed.
Power Windows and Other Power
Options
Fuses in the fuse block protect the power windows.
When the current load is too heavy, the fuse
opens protecting the circuit until the problem is
xed.
342
ProCarManuals.com