horn SATURN AURA 2007 Owners Manual

Page 91 of 406

Q(Lock):Press the lock button to lock all the
doors. The interior lamps will turn off after all of the
doors are closed. If enabled through the Driver
Information Center (DIC), the remote lock feedback
can be programmed to have the horn chirp
and/or the turn signals ash when the RKE
transmitter is used to lock the vehicle’s doors. See
“LOCK HORN” and “LIGHT FLASH” underDIC
Vehicle Personalization on page 187for more
information.
Pressing the lock button may also arm the content
theft-deterrent system. SeeContent
Theft-Deterrent on page 103.
K(Unlock):Press the unlock button to unlock the
driver’s door. If the button is pressed again
within ve seconds, all remaining doors unlock.
The interior lamps turn on and stay on for
20 seconds or until the ignition is turned on. If
enabled through the DIC, the remote unlock
feedback can be programmed to have the horn
chirp and/or the turn signals ash when the
RKE transmitter is used to unlock the vehicle’s
doors. See “UNLOCK HORN” and “LIGHT FLASH”
underDIC Vehicle Personalization on page 187
for more information.If enabled through the DIC, and it is dark enough
outside, the vehicle’s high-beam headlamps,
parking lamps, and back-up lamps will turn on
each time the unlock button on the transmitter is
pressed. These exterior lamps will stay on for
20 seconds, or until a door is opened. See “EXT
(Exterior) LIGHTS” underDIC Vehicle
Personalization on page 187for additional
information.
Pressing the unlock button on the RKE transmitter
will disarm the content theft-deterrent system.
SeeContent Theft-Deterrent on page 103.
V(Remote Trunk Release):Press and hold
this button for about one second to open the trunk.
The trunk can be opened with the transmitter
when the vehicle speed is less than 2 mph
(3 km/h) or when the ignition is off.
L(Vehicle Locator/Panic Alarm):Press and
release this button to locate your vehicle. The horn
sounds three times and the headlamps and turn
signals ash three times. Press and hold the
button for about three seconds to initiate the panic
alarm. The horn sounds and the headlamps
and turn signals ash for 30 seconds. Press the
button again to cancel the panic alarm.
91
ProCarManuals.com

Page 94 of 406

Power Door Locks
The power door lock switches are located on the
driver’s and front passenger’s door.
Press the outboard side of the switch to unlock all
doors. Press the inboard side of the switch to
lock all doors.
The rear doors do not have power door lock
switches. Rear seat passengers must use
the manual lock knob on their doors.
Door Ajar Reminder
If one of the doors is not fully closed while the
ignition is on and the shift lever is moved out of
PARK (P) or NEUTRAL (N) the following will occur:
A chime will sound.
The DOOR AJAR message will display
through the Driver Information Center (DIC)
until the door is closed. SeeDIC Warnings and
Messages on page 182.
Delayed Locking
This feature allows the driver to delay the locking
of the vehicle. It will not operate with the key
in the ignition. SeeLockout Protection on page 97.
Press the driver’s power door lock switch or the
Remote Keyless Entry (RKE) transmitter lock
button once. With the key removed from the
ignition and the driver’s door open, the following
occurs:
Three chimes sound to signal the delay.
All doors will lock and the turn signals ash
once ve seconds after the last door has
been closed.
The horn chirps if the horn chirp feature is
enabled. SeeDIC Vehicle Personalization
on page 187.
If a door is opened before the ve seconds has
elapsed, the doors do not lock until ve seconds
after all doors are closed.
If the power door lock switch or the transmitter
lock button is pressed twice when leaving
the vehicle, the doors lock immediately.
94
ProCarManuals.com

Page 104 of 406

Disarming the System
To disarm the system, do one of the following:
Press the RKE transmitter unlock button.
Turn the ignition to ON.
Once the system is disarmed, the security light will
stop ashing.
How the System Alarm is Activated
To activate the system if it is armed:
Open the driver’s door or trunk. This will
cause a ten second pre-alarm chirp followed
by a thirty second full alarm of horn and lights.
Open any other door. This will immediately
cause a full alarm of horn and lights for
thirty seconds.
Open the hood. If the vehicle has the remote
start feature, it will activate the full alarm.
When an alarm event has nished, the system will
re-arm itself automatically.
How to Turn Off the System Alarm
To turn off the system alarm:
Press the lock button on the RKE transmitter.
The system will then re-arm itself.
Press the unlock button on the RKE
transmitter. This will also disarm the system.
Insert the key in the ignition and turn it on. This
will also disarm the system.
How to Detect a Tamper Condition
If you hear three chirps when the unlock or lock
button is pressed on the RKE transmitter, it means
that the content theft security system alarm was
previously triggered.
104
ProCarManuals.com

Page 135 of 406

Instrument Panel Overview........................ 138
Hazard Warning Flashers.......................... 140
Other Warning Devices............................. 140
Horn.......................................................... 140
Tilt and Telescopic Steering Wheel............ 140
Turn Signal/Multifunction Lever.................. 141
Turn and Lane-Change Signals................. 142
Headlamp High/Low-Beam Changer.......... 142
Flash-to-Pass............................................ 142
Windshield Wipers..................................... 143
Windshield Washer.................................... 144
Cruise Control........................................... 145
Headlamps................................................ 148
Headlamps on Reminder........................... 148
Headlamps Off in PARK (P)...................... 149
Delayed Headlamps.................................. 149
Daytime Running Lamps (DRL)................. 149
Automatic Headlamp System..................... 150
Instrument Panel Brightness...................... 151
Dome Lamp.............................................. 151
Entry/Exit Lighting...................................... 151
Parade Dimming........................................ 152
Overhead Console Reading Lamps........... 152Trunk Lamp............................................... 152
Battery Run-Down Protection..................... 152
Accessory Power Outlet(s)........................ 153
Climate Controls......................................... 154
Automatic Climate Control System............. 154
Outlet Adjustment...................................... 160
Warning Lights, Gages, and Indicators..... 161
Instrument Panel Cluster........................... 162
Speedometer and Odometer...................... 163
Trip Odometer........................................... 163
Tachometer............................................... 163
Safety Belt Reminder Light........................ 163
Passenger Safety Belt Reminder Light....... 164
Airbag Readiness Light............................. 164
Passenger Airbag Status Indicator............. 165
Charging System Light.............................. 167
Brake System Warning Light..................... 168
Antilock Brake System Warning Light........ 169
Low Tire Pressure Warning Light.............. 170
Traction Control System (TCS)
Warning Light........................................ 170
Electronic Stability Control
Indicator Light........................................ 171
Section 3 Instrument Panel
135
ProCarManuals.com

Page 139 of 406

The main components of your instrument panel are the following:
A. Air Outlets. SeeOutlet Adjustment on
page 160.
B. Turn Signal/Multifunction Lever. SeeTurn
Signal/Multifunction Lever on page 141.
C. Instrument Panel Cluster. SeeInstrument Panel
Cluster on page 162.
D. Windshield Wiper and Washer Lever. See
Windshield Wipers on page 143andWindshield
Washer on page 144.
E. Hazard Warning Flashers Button. SeeHazard
Warning Flashers on page 140.
F. Passenger Airbag Status Indicator. See
Passenger Airbag Status Indicator on page 165.
G. Instrument Panel Brightness Control. See
Instrument Panel Brightness on page 151.
H. Cruise Controls. SeeCruise Control on
page 145. Driver Information Center (DIC)
Buttons. SeeDriver Information Center (DIC)
on page 179.
I. Tilt Lever. SeeTilt and Telescopic Steering
Wheel on page 140.J. Horn. SeeHorn on page 140.
K. Audio Steering Wheel Controls (If Equipped).
SeeAudio Steering Wheel Controls on
page 206.
L. Ignition Switch. SeeIgnition Positions on
page 108.
M. Automatic Climate Control System. See
Automatic Climate Control System on
page 154.
N. Traction Control Button. SeeTraction Control
System (TCS) on page 217. Electronic Stability
Control Button. SeeElectronic Stability
Control on page 219.
O. Shift Lever. SeeAutomatic Transaxle Operation
on page 116.
P. Audio System. SeeAudio System(s) on
page 192.
Q. Glove Box. SeeGlove Box on page 131.
139
ProCarManuals.com

Page 140 of 406

Hazard Warning Flashers
The hazard warning ashers let you warn the
police and others that you have a problem. The
front and rear turn signal lamps will ash on
and off.
The hazard warning
asher button is located
towards the center of
the instrument panel.
Press the button to make the front and rear turn
signal lamps ash on and off. Press the button
again to turn the ashers off.
While the hazard warning ashers are on, the turn
signals do not work.
The hazard warning ashers work no matter what
position the key is in, and even if the key is not
in the ignition switch.
Other Warning Devices
If you carry reective triangles, you can set them
up at the side of the road about 300 feet
(100 m) behind your vehicle.
Horn
Press near or on the horn symbols on the steering
wheel pad to sound the horn.
Tilt and Telescopic Steering Wheel
A tilt and telescope wheel lets you adjust the
steering wheel before you drive. The steering
wheel can be raised to the highest level to give
your legs more room when you enter and exit the
vehicle.
The lever that lets you tilt and telescope the
steering wheel is located on the left side of the
steering column.
140
ProCarManuals.com

Page 151 of 406

Instrument Panel Brightness
The control for this
feature is located on the
instrument panel to
the left of the steering
wheel.
Turn the knob clockwise or counterclockwise to
brighten or dim the lights.
Dome Lamp
Your vehicle might have a dome lamp without a
switch. If the dome lamp has a switch, the
following are the settings.
9(Off):Move the lever to this position to turn
the lamp off, even when a door is open.
1(Door):Move the lever to this position so that
the lamp comes on when a door is opened.
+(On):Move the lever to this position to turn
the dome lamp on.
Entry/Exit Lighting
The lamps inside the vehicle come on when any
door is opened. These lamps fade out about
20 seconds after all of the doors have been closed
or when the ignition is turned to ON. They also
go on when you press the unlock symbol button or
the horn symbol on the Remote Keyless Entry
(RKE) system transmitter.
The lamps inside the vehicle stay on for about
20 seconds after the key is removed from
the ignition to provide light as you exit.
151
ProCarManuals.com

Page 188 of 406

Personalization Menu Modes
OIL LIFE RESET
When this feature is displayed, you can reset the
engine oil life system. To reset the system,
seeEngine Oil Life System on page 268. See
“OIL LIFE” underDIC Operation and Displays on
page 180for more information.
UNITS
This feature allows you to select the units of
measurement in which the DIC will display the
vehicle information. When UNITS appears on the
display, press and hold the reset button for at
least one second to scroll through the available
settings:
ENGLISH (default in United States):All
information will be displayed in English units.
METRIC (default in Canada):All information will
be displayed in metric units.
Choose one of the available settings and press
the information button to select it and move on to
the next feature.
LOCK HORN
If your vehicle has Remote Keyless Entry (RKE),
this feature, which allows the vehicle’s horn to
chirp every time the lock button on the RKE
transmitter is pressed, can be enabled or disabled.
When LOCK HORN appears on the display,
press and hold the reset button for at least one
second to scroll through the available settings:
OFF (default):The horn will not chirp on the rst
press of the lock button on the RKE transmitter.
The horn will still chirp on the second press.
ON:The horn will chirp on the rst press of the
lock button on the RKE transmitter.
SeeRemote Keyless Entry (RKE) System
Operation on page 90for more information.
Choose one of the available settings and press
the information button to select it and move on to
the next feature.
188
ProCarManuals.com

Page 189 of 406

UNLOCK HORN
If your vehicle has Remote Keyless Entry (RKE),
this feature, which allows the vehicle’s horn to
chirp on the rst press of the unlock button on the
RKE transmitter, can be enabled or disabled.
When UNLOCK HORN appears on the display,
press and hold the reset button for at least
one second to scroll through the available settings:
OFF (default):The horn will not chirp when the
unlock button on the RKE transmitter is pressed.
ON:The horn will chirp on the rst press of
the unlock button on the RKE transmitter.
SeeRemote Keyless Entry (RKE) System
Operation on page 90for more information.
Choose one of the available settings and press
the information button to select it and move on to
the next feature.
LIGHT FLASH
If your vehicle has Remote Keyless Entry (RKE),
this feature, which allows the vehicle’s exterior
hazard/turn signal lighting to ash every time the
lock, unlock, or trunk release buttons on the
RKE transmitter are pressed, can be enabled or
disabled. When LIGHT FLASH appears on
the display, press and hold the reset button for at
least one second to scroll through the available
settings:
OFF:The exterior hazard/turn signal lighting will
not ash when the lock, unlock, or trunk release
buttons on the RKE transmitter are pressed.
ON (default):The exterior hazard/turn signal
lighting will ash when the lock, unlock, or trunk
release buttons on the RKE transmitter are
pressed.
SeeRemote Keyless Entry (RKE) System
Operation on page 90for more information.
Choose one of the available settings and press
the information button to select it and move on to
the next feature.
189
ProCarManuals.com

Page 308 of 406

TPMS Sensor Identication Codes
Each TPMS sensor has a unique identication
code. Any time you replace one or more of
the TPMS sensors or rotate the vehicle’s tires, the
identication codes need to be matched to the
new tire/wheel position. The sensors are matched,
to the tire/wheel positions, in the following order:
driver side front tire, passenger side front tire,
passenger side rear tire, and driver side rear tire
using a TPMS diagnostic tool. See your Saturn
retailer for service.
The TPMS sensors can also be matched to each
tire/wheel position by increasing or decreasing
the tire’s air pressure. When increasing the tire’s
pressure, do not exceed the maximum ination
pressure indicated on the tire’s sidewall. To
decrease the tire’s air-pressure use the pointed
end of the valve cap, a pencil-style air pressure
gage, or a key.
You have two minutes to match each tire and wheel
position. If it takes longer than two minutes to match
any tire and wheel position, the matching process
stops and you need to start over.The TPMS matching process is outlined below:
1. Set the parking brake.
2. Turn the ignition switch to ON with the
engine off.
3. Press and hold both the Lock and Unlock
buttons on the Remote Keyless Entry
(RKE) transmitter, at the same time, for
approximately ve seconds or until you hear
the horn sound twice.
4. The horn sounding twice indicates the
receiver is ready to learn the TPMS sensors.
The driver side front turn signal comes on
indicating that corner’s sensor is ready to be
learned.
5. Start with the driver side front tire.
6. Remove the valve cap from the tire’s valve
stem. Activate the TPMS sensor by increasing
or decreasing the tire’s air pressure for
about eight seconds. The horn chirp, can take
up to 30 seconds to sound. It sounds one
time and all the turn signals ash one time to
conrm the sensor identication code has
been matched to the tire/wheel position.
308
ProCarManuals.com

Page:   1-10 11-20 next >