SATURN OUTLOOK 2009 Owners Manual

File System and Naming
The song name that is displayed is
the song name that is contained in
the ID3 tag. If the song name is not
present in the ID3 tag, then the radio
displays the le name without the
extension (such as .mp3) as the
track name.
Track names longer than
32 characters or four pages
are shortened. Parts of words
on the last page of text and the
extension of the lename displays.
Preprogrammed Playlists
Preprogrammed playlists that
were created using WinAmp™,
MusicMatch™, or Real Jukebox™
software can be accessed, however,
they cannot be edited using the
radio. These playlists are treated
as special folders containing
compressed audio song les.Playing an MP3/WMA
(In Either the DVD or CD Slot)
Insert a CD-R or CD-RW disc
partway into either the top or bottom
slot, label side up. The player pulls it
in, and the CD-R or CD-RW should
begin playing.
Depending on the format of
the disc, a softkey menu appears
and allows navigation of the disc.
The menu reads left to right as
RDM (Randomize song play order),
a Folder icon with left and right
arrows (to move up or down through
available folders), a PL tag if the disc
has a Playlist available, and a Music
Navigator tag. If a Playlist tag is
shown, toggling this key brings up a
Folder softkey only or the menu as
previously described.
If the ignition or radio is turned off
with a CD-R or CD-RW disc in the
player it stays in the player. When
the ignition or radio is turned backon, the CD-R or CD-RW starts to
play where it stopped, if it was the
last selected audio source.
As each new track starts to play,
the track number and song title
displays.
ZCD (Eject):Press and release
this button to eject the CD-R or
CD-RW that is currently playing
in the bottom slot. A beep sounds
and Ejecting Disc displays. Once
the disc is ejected, Remove Disc
displays. The CD-R or CD-RW disc
can be removed. If the CD-R or
CD-RW disc is not removed, after
several seconds, the CD-R or
CD-RW disc automatically pulls
back into the player.
If loading and reading of a CD cannot
be completed, such as unknown
format, etc., and the disc fails to
eject, press and hold this button for
more than ve seconds to force the
disc to eject.
Instrument Panel 3-99
ProCarManuals.com

ZDVD (Eject):Press and release
this button to eject the CD-R or
CD-RW that is currently playing in
the top slot. A beep sounds and
Ejecting Disc displays. Once the disc
is ejected, Remove Disc displays.
The CD-R or CD-RW disc can be
removed. If the CD-R or CD-RW
disc is not removed, after several
seconds, the CD-R or CD-RW disc
automatically pulls back into the
player. If loading and reading of a
CD cannot be completed, such as
unknown format, etc., and the disc
fails to eject, press and hold this
button for more than ve seconds to
force the disc to eject.
f(Tune):Turn this knob to select
MP3/WMA les on the CD-R or
CD-RW that is currently playing.
©SEEK¨:Press the left
SEEK arrow to go to the start
of the current MP3/WMA le,
if more than ve seconds have
played. If less than ve seconds
have played, the previous MP3/WMA
le plays. Press the right SEEK
arrow to go to the next MP3/WMA
le. If either SEEK arrow is held, or
pressed multiple times, the player
continues moving backward or
forward through the MP3/WMA
les on the CD.
Sc(Previous Folder):Press
the pushbutton positioned under
the Folder label to go to the
rst track in the previous folder.
cT(Next Folder):Press
the pushbutton positioned under
the Folder label to go to the
rst track in the next folder.
sREV (Reverse):Press and
hold this button to reverse playback
quickly within an MP3/WMA le.
Sound is heard at a reduced volume.
Release this button to resume
playing the le. The elapsed time
of the le displays.
\FWD (Fast Forward):Press
and hold this button to advance
playback quickly within an MP3/
WMA le. Sound is heard at a
reduced volume. Release this
button to resume playing the le.
The elapsed time of the le displays.
RDM (Random):With the random
setting, MP3/WMA les on the CD-R
or CD-RW can be listened to in
random, rather than sequential order.
To play MP3/WMA les from the
CD-R or CD-RW in random order,
press the pushbutton positioned
under the RDM label until Random
Current Disc displays. Press the
same pushbutton again to turn off
random play.
3-100 Instrument Panel
ProCarManuals.com

h(Music Navigator):Use the
music navigator feature to play
MP3/WMA les on the CD-R or
CD-RW in order by artist or album.
Press the pushbutton located below
the music navigator label. The player
scans the disc to sort the les by
artist and album ID3 tag information.
It could take several minutes to scan
the disc depending on the number
of MP3/WMA les recorded to the
CD-R or CD-RW disc.
To cancel music navigator while
the player is scanning, press the
pushbutton located below the music
navigator label or eject the disc.
The radio can begin playing while it is
scanning the disc in the background.
When the scan is nished, the CD-R
or CD-RW begins playing again.Once the disc has been scanned, the
player defaults to playing MP3/WMA
les in order by artist. The current
artist playing is shown on the second
line of the display between the
arrows. To listen to MP3/WMA
les by another artist, press the
pushbutton located below either
arrow button. The disc goes to the
next or previous artist in alphabetical
order. Continue pressing either
button until the desired artist is
displayed.
To change from playback by artist
to playback by album, press the
pushbutton located below the Sort
By label. From the sort screen, push
one of the buttons below the album
button. Press the pushbutton below
the back label to return to the main
music navigator screen. Now the
album name displays on the second
line between the arrows and songs
from the current album begin to play.Once all songs from that album are
played, the player moves to the next
album in alphabetical order on the
CD-R or CD-RW and begins playing
MP3/WMA les from that album.
To exit music navigator mode, press
the pushbutton below the Back label
to return to normal MP3/WMA
playback.
BAND:Press this button to listen to
the radio when a CD or a DVD is
playing. The CD or DVD remains
inside the radio for future listening
or viewing entertainment.
DVD/CD AUX (Auxiliary):Press
this button to cycle through DVD,
CD, or Auxiliary when listening to
the radio. The DVD/CD text label
and a message showing track or
chapter number displays when
a disc is in either slot. Press this
button again and the system
automatically searches for an
auxiliary input device, such
as a portable audio player.
Instrument Panel 3-101
ProCarManuals.com

If a portable audio player
is not connected, “No Aux Input
Device” displays. If a disc is in both
the DVD slot and the CD slot the
DVD/CD AUX button cycles between
the two sources and does not
indicate “No Aux Input Device”.
If a front auxiliary device is
connected, the DVD/CD AUX
button cycles through all available
options, such as: DVD slot, CD slot,
Front Auxiliary, and Rear Auxiliary
(if available). See “Using the
Auxiliary Input Jack(s)” later in this
section, or “Audio/Video (A/V) Jacks”
under,Rear Seat Entertainment
(RSE) System on page 3-114for
more information.
If a MP3/WMA is inserted into top
DVD slot, the rear seat operator can
turn on the video screen and use the
remote control to navigate the CD
(tracks only).XM Radio Messages
XL (Explicit Language Channels):
These channels, or any others, can
be blocked at a customer’s request,
by calling 1-800-852-XMXM (9696).
XM Updating:The encryption code
in the receiver is being updated, and
no action is required. This process
should take no longer than
30 seconds.
No XM Signal:The system is
functioning correctly, but the vehicle
is in a location that is blocking
the XM™ signal. When the vehicle
is moved into an open area, the
signal should return.
Loading XM:The audio system
is acquiring and processing audio
and text data. No action is needed.
This message should disappear
shortly.Channel Off Air:This channel
is not currently in service. Tune
in to another channel.
Channel Unauth:This channel is
blocked or cannot be received with
your XM Subscription package.
Channel Unavail:This previously
assigned channel is no longer
assigned. Tune to another station.
If this station was one of the presets,
choose another station for that
preset button.
No Artist Info:No artist information
is available at this time on this
channel. The system is working
properly.
No Title Info:No song title
information is available at this time
on this channel. The system is
working properly.
3-102 Instrument Panel
ProCarManuals.com

No CAT Info:No category
information is available at this
time on this channel. The system
is working properly.
No Information:No text or
informational messages are
available at this time on this
channel. The system is working
properly.
CAT Not Found:There are no
channels available for the selected
category. The system is working
properly.
XM Theftlocked:The XM receiver
in the vehicle could have previously
been in another vehicle. For security
purposes, XM receivers cannot be
swapped between vehicles. If this
message is received after having the
vehicle serviced, check with your
dealer/retailer.XM Radio ID:If tuned to channel 0,
this message alternates with the
XM™ Radio 8 digit radio ID label.
This label is needed to activate the
service.
Unknown:If this message is
received when tuned to channel 0,
there could be a receiver fault.
Consult with your dealer/retailer.
Check XM Receivr:If this
message does not clear within a
short period of time, the receiver
could have a fault. Consult with
your dealer/retailer.
XM Not Available:If this message
does not clear within a short period of
time, the receiver could have a fault.
Consult with your dealer/retailer.Navigation/Radio System
For vehicles with a navigation
radio system, see the separate
Navigation System manual.
Bluetooth®
Vehicles with a Bluetooth system
can use a Bluetooth capable cell
phone with a Hands Free Prole to
make and receive phone calls. The
system can be used while the key is
in ON/RUN or ACC/ACCESSORY
position. The range of the Bluetooth
system can be up to 30 ft. (9.1 m).
Not all phones support all functions,
and not all phones are guaranteed to
work with the in-vehicle Bluetooth
system. See gm.com/bluetooth for
more information on compatible
phones.
Instrument Panel 3-103
ProCarManuals.com

Voice Recognition
The Bluetooth system uses voice
recognition to interpret voice
commands to dial phone numbers
and name tags.
Noise:Keep interior noise levels to
a minimum. The system may not
recognize voice commands if there
is too much background noise.
When to Speak:A short tone
sounds after the system responds
indicating when it is waiting for
a voice command. Wait until
the tone and then speak.
How to Speak:Speak clearly in a
calm and natural voice.
Audio System
When using the in-vehicle Bluetooth
system, sound comes through
the vehicle’s front audio system
speakers and overrides the audio
system. Use the audio systemvolume knob, during a call,
to change the volume level.
The adjusted volume level
remains in memory for later calls.
To prevent missed calls, a minimum
volume level is used if the volume
is turned down too low.
Bluetooth Controls
Use the buttons located on the
steering wheel to operate the
in-vehicle Bluetooth system. See
Audio Steering Wheel Controls on
page 3-125for more information.
bg(Push To Talk):Press to
answer incoming calls, to conrm
system information, and to start
speech recognition.
cx(Phone On Hook):Press to
end a call, reject a call, or to cancel
an operation.
Pairing
A Bluetooth enabled cell phone
must be paired to the in-vehicle
Bluetooth system rst and then
connected to the vehicle before it
can be used. See the cell phone
manufacturers user guide for
Bluetooth functions before pairing
the cell phone. If a Bluetooth phone
is not connected, calls will be
made using OnStar
®Hands-Free
Calling, if available. Refer to
the OnStar owner’s guide for
more information.
Pairing Information:
Up to ve cell phones can
be paired to the in-vehicle
Bluetooth system.
The pairing process is disabled
when the vehicle is moving.
The in-vehicle Bluetooth system
automatically links with the rst
available paired cell phone in the
order the phone was paired.
3-104 Instrument Panel
ProCarManuals.com

Only one paired cell phone can
be connected to the in-vehicle
Bluetooth system at a time.
Pairing should only need to be
completed once, unless changes
to the pairing information have
been made or the phone is
deleted.
To link to a different paired phone,
see Linking to a Different Phone
later in this section.
Pairing a Phone
1. Press and hold
bgfor
two seconds. The system
responds with “Ready”
followed by a tone.
2. Say “Bluetooth”. The system
responds with “Bluetooth
ready” followed by a tone.
3. Say “Pair”. The system responds
with instructions and a four digit
PIN number. The PIN number
will be used in Step 4.4. Start the Pairing process on the
cell phone that will be paired to
the vehicle. Reference the cell
phone manufacturers user guide
for information on this process.
Locate the device named
“General Motors” in the list on
the cellular phone and follow the
instructions on the cell phone
to enter the four digit PIN number
that was provided in Step 3.
5. The system prompts for a
name for the phone. Use a name
that best describes the phone.
This name will be used to indicate
which phone is connected. The
system then conrms the name
provided.
6. The system responds with
“<Phone name> has been
successfully paired” after the
pairing process is complete.
7. Repeat Steps 1 through 7 for
additional phones to be paired.Listing All Paired and Connected
Phones
1. Press and hold
bgfor
two seconds. The system
responds with “Ready”
followed by a tone.
2. Say “Bluetooth”. The system
responds with “Bluetooth
ready” followed by a tone.
3. Say “List”. The system lists all
the paired Bluetooth devices.
If a phone is connected to
the vehicle, the system will
say “Is connected” after the
connected phone.
Deleting a Paired Phone
1. Press and hold
bgfor
two seconds. The system
responds with “Ready”
followed by a tone.
2. Say “Bluetooth”. The system
responds with “Bluetooth
ready” followed by a tone.
3. Say “Delete”. The system asks
which phone to delete followed
by a tone.
Instrument Panel 3-105
ProCarManuals.com

4. Say the name of the phone to
be deleted. If the phone name is
unknown, use the “List” command
for a list of all paired phones. The
system responds with “Would you
like to delete <phone name>?
Yes or No” followed by a tone.
5. Say “Yes” to delete the phone.
The system responds with
“OK, deleting <phone name>”.
Linking to a Different Phone
1. Press and hold
bgfor
two seconds. The system
responds with “Ready”
followed by a tone.
2. Say “Bluetooth”. The system
responds with “Bluetooth
ready” followed by a tone.3. Say “Change phone”. The
system responds with “Please
wait while I search for other
phones”.
If another phone is found,
the response will be “<Phone
name> is now connected”.
If another phone is not found,
the original phone remains
connected.
Storing Name Tags
The system can store up to thirty
phone numbers as name tags
that are shared between the
Bluetooth and OnStar systems.
The system uses the following
commands to store and retrieve
phone numbers:
Store
Digit Store
DirectoryUsing the Store Command
The store command allows a phone
number to be stored without
entering the digits individually.
1. Press and hold
bgfor
two seconds. The system
responds with “Ready”
followed by a tone.
2. Say “Store”. The system
responds with “Store, number
please” followed by a tone.
3. Say the complete phone number
to be stored at once with no
pauses.
If the system recognizes the
number it responds with
“OK, Storing” and repeats
the phone number.
If the system is unsure it
recognizes the phone number,
it responds with “Store” and
repeats the number followed
by “Please say yes or no”.
If the number is correct, say
“Yes”. If the number is not
correct, say “No”. The system
will ask for the number to be
re-entered.
3-106 Instrument Panel
ProCarManuals.com

4. After the system stores the
phone number, it responds
with “Please say the name tag”
followed by a tone.
5. Say a name tag for the phone
number. The name tag is
recorded and the system
responds with “About to
store <name tag>. Does
that sound OK?”.
If the name tag does not sound
correct, say “No” and repeat
Step 5.
If the name tag sounds
correct, say “Yes” and the
name tag is stored. After the
number is stored the system
returns to the main menu.Using the Digit Store Command
The digit store command allows
a phone number to be stored
by entering the digits individually.
1. Press and hold
bgfor
two seconds. The system
responds with “Ready”
followed by a tone.
2. Say “Digit Store”. The system
responds with “Please say the
rst digit to store” followed
by a tone.
3. Say the rst digit to be stored.
The system will repeat back
the digit it heard followed by a
tone. Continue entering digits
until the number to be stored
is complete.
If an unwanted number is
recognized by the system,
say “Clear” at any time
to clear the last number.
To hear all of the numbers
recognized by the system,
say “Verify” at any time
and the system will
repeat them.4. After the complete number has
been entered, say “Store”.
The system responds with
“Please say the name tag”
followed by a tone.
5. Say a name tag for the phone
number. The name tag is
recorded and the system
responds with “About to
store <name tag>. Does
that sound OK?”.
If the name tag does not sound
correct, say “No” and repeat
Step 5.
If the name tag sounds
correct, say “Yes” and the
name tag is stored. After the
number is stored the system
returns to the main menu.
Instrument Panel 3-107
ProCarManuals.com

Using the Directory Command
The directory command lists
all of the name tags stored by
the system. To use the directory
command:
1. Press and hold
bgfor
two seconds. The system
responds with “Ready”
followed by a tone.
2. Say “Directory”. The system
responds with “Directory”
and then plays back all of the
stored name tags. When the
list is complete, the system
returns to the main menu.
Deleting Name Tags
The system uses the following
commands to delete name tags:
Delete
Delete all name tagsUsing the Delete Command
The delete command allows specic
name tags to be deleted.
To use the delete command:
1. Press and hold
bgfor
two seconds. The system
responds with “Ready”
followed by a tone.
2. Say “Delete”. The system
responds with “Delete, please
say the name tag” followed
by a tone.
3. Say the name tag to be deleted.
The system responds with
“Would you like to delete, <name
tag>? Please say yes or no”.
If the name tag is correct, say
“Yes” to delete the name tag.
The system responds with
“OK, deleting <name tag>,
returning to the main menu.”
If the name tag is incorrect,
say “No”. The system
responds with “No. OK,
let’s try again, please say
the name tag.”Using the Delete All Name Tags
Command
The delete all name tags command
deletes all stored phone book name
tags and route name tags for OnStar
(if present).
To use the delete all name tags
command:
1. Press and hold
bgfor
two seconds. The system
responds with “Ready” followed
by a tone.
2. Say “Delete all name tags”.
The system responds with
“You are about to delete all
name tags stored in your
phone directory and your route
destination directory. Are you
sure you want to do this? Please
say yes or no.”
Say “Yes” to delete all
name tags.
Say “No” to cancel the function
and return to the main menu.
3-108 Instrument Panel
ProCarManuals.com