service SATURN VUE 2009 Owners Manual

Changing a Flat Tire
If a tire goes at, avoid further tire
and wheel damage by driving slowly
to a level place. Turn on the hazard
warning ashers. SeeHazard
Warning Flashers on page 3-5.
{CAUTION
Changing a tire can be dangerous.
The vehicle can slip off the jack
and roll over or fall on you or other
people. You and they could be
badly injured or even killed. Find
a level place to change your tire.
To help prevent the vehicle from
moving:
1. Set the parking brake rmly.
2. Put an automatic
transmission shift lever in
P (Park), or shift a manual
transmission to 1 (First) or
R (Reverse).
(Continued)
CAUTION (Continued)
3. Turn off the engine and do
not restart while the vehicle
is raised.
4. Do not allow passengers to
remain in the vehicle.
To be certain the vehicle will not
move, put blocks at the front and
rear of the tire farthest away from
the one being changed. That
would be the tire on the other
side, at the opposite end of the
vehicle.
When the vehicle has a at tire (B),
use the following example as a
guide to assist you in the placement
of wheel blocks (A).A. Wheel Block
B. Flat Tire
The following information explains
how to use the jack and change
a tire.
5-64 Service and Appearance Care
ProCarManuals.com

Removing the Spare Tire
and Tools
To access the spare tire:
1. Open the liftgate.
2. Push the levers on the load oor.3. Lift the load oor and hang the
hook to the tailgate opening.
4. Remove the tire protector foam.5. Remove the wheel retainer bolt
holding down the spare tire by
turning it counterclockwise.
6. Remove the compact spare tire.
SeeCompact Spare Tire on
page 5-71for more information.
Service and Appearance Care 5-65
ProCarManuals.com

The tools are located between the
compact spare tire and the
liftgate. To access the tools:
A. Tool Bag
B. Wing-bolt
C. Jack
1. Remove the wing-bolt (B) from
the jack.
2. Remove the jack (C) and tool
bag (A).3. Remove the straps holding the
bag containing the wheel wrench
and extension jack handle.
Remove the wheel wrench and
extension jack handle from
the bag.
The tools you will be using include:
A. Tool Bag
B. Jack
C. Wheel Wrench
D. Extension Jack HandleRemoving the Flat Tire
and Installing the
Spare Tire
1. Do a safety check before
proceeding. SeeChanging a Flat
Tire on page 5-64for more
information.
2. Use the wheel wrench to loosen
all the wheel nuts. Do not remove
them yet.
3. Attach the wheel wrench to the
jack bolt head and rotate the
wheel wrench clockwise to raise
the lift head a little.
5-66 Service and Appearance Care
ProCarManuals.com

4. Position the lift head at the jack
location nearest the at tire. Make
sure all of the jack lift head is
touching the jacking ange under
the body. Do not place the jack
under a body panel. The lower
body panel has an arrow to aid in
locating the jacking location.
5. Put the compact spare tire
near you.6. Raise the vehicle by turning
the jack handle clockwise. Raise
the vehicle far enough off the
ground so there is enough room
for the road tire to be removed.
{CAUTION
Getting under a vehicle when it is
jacked up is dangerous. If the
vehicle slips off the jack, you
could be badly injured or killed.
Never get under a vehicle when it
is supported only by a jack.
{CAUTION
Raising your vehicle with the jack
improperly positioned can damage
the vehicle and even make the
vehicle fall. To help avoid
personal injury and vehicle
damage, be sure to t the jack lift
head into the proper location
before raising the vehicle.
Service and Appearance Care 5-67
ProCarManuals.com

{CAUTION
Lifting a vehicle and getting under
it to do maintenance or repairs is
dangerous without the appropriate
safety equipment and training. If a
jack is provided with the vehicle, it
is designed only for changing a
at tire. If it is used for anything
else, you or others could be badly
injured or killed if the vehicle slips
off the jack. If a jack is provided
with the vehicle, only use it for
changing a at tire.
Notice:Make sure that the jack
lift head is in the correct
position or you may damage your
vehicle. The repairs would not
be covered by your warranty.
7. Remove all of the wheel nuts.
8. Remove the at tire.9. Remove any rust or dirt from the
wheel bolts, mounting surfaces
and spare wheel.
{CAUTION
Rust or dirt on a wheel, or on the
parts to which it is fastened, can
make wheel nuts become loose
after time. The wheel could come
off and cause an accident. When
changing a wheel, remove any
rust or dirt from places where the
wheel attaches to the vehicle. In
an emergency, use a cloth or a
paper towel to do this; but be sure
to use a scraper or wire brush
later, if needed, to get all the rust
or dirt off. SeeChanging a Flat
Tire on page 5-64.
10. Place the compact spare tire on
the wheel-mounting surface.11. Reinstall the wheel nuts. Tighten
each nut by hand until the wheel
is held against the hub.
{CAUTION
Never use oil or grease on bolts
or nuts because the nuts might
come loose. The vehicle’s wheel
could fall off, causing a crash.
12. Lower the vehicle by turning the
jack handle counterclockwise.
5-68 Service and Appearance Care
ProCarManuals.com

13. Tighten the wheel nuts rmly in
a crisscross sequence, as
shown.
{CAUTION
Wheel nuts that are improperly or
incorrectly tightened can cause the
wheels to become loose or come
off. The wheel nuts should be
(Continued)
CAUTION (Continued)
tightened with a torque wrench to
the proper torque specication
after replacing. Follow the torque
specication supplied by the
aftermarket manufacturer when
using accessory locking wheel
nuts. SeeCapacities and
Specifications on page 5-86for
original equipment wheel nut
torque specications.
Notice:Improperly tightened
wheel nuts can lead to brake
pulsation and rotor damage. To
avoid expensive brake repairs,
evenly tighten the wheel nuts in
the proper sequence and to
the proper torque specication.
SeeCapacities and Specifications
on page 5-86for the wheel nut
torque specication.14. Lower the jack all the way and
remove the jack from under the
vehicle.
15. Tighten the bolts rmly with the
wheel wrench.
When reinstalling full plastic covers
or center caps, tighten all the plastic
caps hand snug, then tighten with
the wheel wrench an additional
one-quarter of a turn.
Notice:Wheel covers will not t
on your vehicle’s compact spare.
If you try to put a wheel cover on
the compact spare, the cover or
the spare could be damaged.
Service and Appearance Care 5-69
ProCarManuals.com

Storing a Flat or Spare
Tire and Tools
{CAUTION
Storing a jack, a tire, or other
equipment in the passenger
compartment of the vehicle could
cause injury. In a sudden stop or
collision, loose equipment could
strike someone. Store all these in
the proper place.
To store the at or spare tire and
tools, do the following:
1. Place the wheel wrench into the
bag and use the straps to secure
the bag to the fully collapsed jack.2. Install the jack between the back
of the trunk and the compact
spare tire and secure with the
wing bolt.
3. Reverse Steps 1 through 3 under
Removing the Spare Tire and
Tools on page 5-65to replace
the oor and lock in place.
4. Place the at, or damaged tire,
face down, on the bottom of
the spare tire compartment.
Before
After
5-70 Service and Appearance Care
ProCarManuals.com

5. Remove the disk (A) from the
retainer bolt. Turn the disk (A)
over and place it back on
the retainer bolt.
Return the disk back to its original
position after removing the at tire
from the spare tire compartment
and before storing the spare tire.
6. Place the wheel retainer bolt
onto the wheel stow rod and
tighten by turning it clockwise.
The compact spare is for temporary
use only. Replace the compact spare
tire with a full-size tire as soon as
possible.Compact Spare Tire
{CAUTION
Driving with more than one
compact spare tire at a time could
result in loss of braking and
handling. This could lead to a
crash and you or others could be
injured. Use only one compact
spare tire at a time.
The compact spare tire was fully
inated when the vehicle was
new, however, it can lose air after a
time. Check the ination pressure
regularly. It should be 60 psi
(414 kPa).
After installing the compact spare
on your vehicle, you should stop as
soon as possible and make sure
your spare tire is correctly inated.
The compact spare is intended to
perform well at speeds up to 50 mph
(80 km/h), so you can nish your tripand have your full-size tire repaired
or replaced where you want. Replace
your spare with a full-size tire as
soon as you can.
Notice:When the compact spare
is installed, do not take the vehicle
through an automatic car wash
with guide rails. The compact
spare can get caught on the rails
which can damage the tire, wheel
and other parts of the vehicle.
Do not use your compact spare on
other vehicles.
Do not mix your compact spare tire
or wheel with other wheels or tires.
Keep your spare tire and its wheel
together.
Notice:Tire chains will not t
the compact spare. Using them
can damage the vehicle and can
damage the chains too. Do not use
tire chains on the compact spare.
Service and Appearance Care 5-71
ProCarManuals.com

Appearance Care
Interior Cleaning
The vehicle’s interior will continue
to look its best if it is cleaned often.
Although not always visible, dust
and dirt can accumulate on the
upholstery. Dirt can damage carpet,
fabric, leather, and plastic surfaces.
Regular vacuuming is recommended
to remove particles from the
upholstery. It is important to keep
the upholstery from becoming and
remaining heavily soiled. Soils
should be removed as quickly as
possible. The vehicle’s interior may
experience extremes of heat that
could cause stains to set rapidly.
Lighter colored interiors may
require more frequent cleaning.
Use care because newspapers and
garments that transfer color to home
furnishings may also transfer color to
the vehicle’s interior.When cleaning the vehicle’s interior,
only use cleaners specically
designed for the surfaces being
cleaned. Permanent damage may
result from using cleaners on
surfaces for which they were not
intended. Use glass cleaner only on
glass. Remove any accidental
over-spray from other surfaces
immediately. To prevent over-spray,
apply cleaner directly to the cleaning
cloth.
Notice:Using abrasive cleaners
when cleaning glass surfaces
on the vehicle, could scratch the
glass and/or cause damage to
the rear window defogger. When
cleaning the glass on the vehicle,
use only a soft cloth and glass
cleaner.Many cleaners contain solvents that
may become concentrated in the
vehicle’s breathing space. Before
using cleaners, read and adhere to
all safety instructions on the label.
While cleaning the vehicle’s interior,
maintain adequate ventilation by
opening the vehicle’s doors and
windows.
Dust may be removed from small
buttons and knobs using a small
brush with soft bristles.
Products that remove odors from the
vehicle’s upholstery and clean the
vehicle’s glass can be obtained from
your dealer/retailer.
5-72 Service and Appearance Care
ProCarManuals.com

Do not clean the vehicle using:
A knife or any other sharp object
to remove a soil from any interior
surface.
A stiff brush. It can cause damage
to the vehicle’s interior surfaces.
Heavy pressure or aggressive
rubbing with a cleaning cloth. Use
of heavy pressure can damage
the interior and does not improve
the effectiveness of soil removal.
Laundry detergents or
dishwashing soaps with
degreasers can leave residue
that streaks and attracts dirt. For
liquid cleaners, about 20 drops
per gallon (3.78 L) of water is a
good guide. Use only mild,
neutral-pH soaps.
Too much cleaner that saturates
the upholstery.
Organic solvents such as naptha,
alcohol, etc. that can damage the
vehicle’s interior.
Fabric/Carpet
Use a vacuum cleaner with a soft
brush attachment frequently to
remove dust and loose dirt. A
canister vacuum with a beater bar in
the nozzle may only be used on oor
carpet and carpeted oor mats. For
any soil, always try to remove it rst
with plain water or club soda. Before
cleaning, gently remove as much of
the soil as possible using one of the
following techniques:
For liquids: gently blot the
remaining soil with a paper towel.
Allow the soil to absorb into the
paper towel until no more can be
removed.
For solid dry soils: remove as
much as possible and then
vacuum.
To clean:
1. Saturate a lint-free, clean white
cloth with water or club soda.
2. Wring the cloth to remove excess
moisture.3. Start on the outside edge of the
soil and gently rub toward the
center. Continue cleaning, using
a clean area of the cloth each
time it becomes soiled.
4. Continue to gently rub the soiled
area until the cleaning cloth
remains clean.
5. If the soil is not completely
removed, use a mild soap
solution and repeat the cleaning
process that was used with
plain water.
If any of the soil remains, a
commercial fabric cleaner or spot
lifter may be necessary. When a
commercial upholstery cleaner or
spot lifter is to be used, test a small
hidden area for colorfastness rst.
If the locally cleaned area gives any
impression that a ring formation may
result, clean the entire surface.
After the cleaning process has been
completed, a paper towel can be
used to blot excess moisture from
the fabric or carpet.
Service and Appearance Care 5-73
ProCarManuals.com