window SATURN VUE HYBRID 2008 Owner's Manual

Climate Controls
Automatic Climate Control System
The heating, cooling, and ventilation for the vehicle can
be controlled with this system.
Climate Control Inuence on Hybrid
Operation and Fuel Economy
To maximize your fuel economy, use the following
settings:
Set the fan knob to AUTO.
Set the air delivery knob to AUTO.
Select an air temperature setting near 75°F (23°C).
Select the Hybrid A/C button, if A/C is required.Avoid using these settings that may lead to fewer auto
stops and to higher fuel consumption:
Manual fan speed operation.
Defrost mode. Only use this setting to clear the
windows.
Extreme cold or hot air temperature settings, such
as 60°F (16°C) or 90°F (32°C).
Normal air conditioning mode, if A/C is required.
Automatic Operation
This climate control system automatically maintains the
desired temperature inside the vehicle.
Do not cover the sensor located on the top of the
instrument panel near the windshield or the sensor grille
below the climate control faceplate. These two sensors
help regulate the inside air temperature.
AUTO (Automatic Fan):Turn the fan knob to AUTO
for the system to automatically adjust the fan speed
to reach the desired inside temperature.
Temperature Control:Select the desired air
temperature between 60-90°F (16-32°C). Typically,
the best setting is near 75°F (23°C). Choosing the
coldest or warmest temperature setting does not
cause the system to heat or cool any faster.
3-18
ProCarManuals.com

To change the current air delivery mode, use the right
knob to select one of the following:
H(Vent):This mode directs air to the instrument
panel outlets.
)(Bi-Level):This mode divides the air between the
instrument panel outlets and the oor outlets.
6(Floor):This mode directs most of the air to the
oor outlets with some air directed to the windshield.
When this mode is selected, the system turns the
recirculation mode off. Recirculation mode cannot be
selected while in oor mode. This is to help prevent
window fogging.
The right knob can also be used to select defog or
defrost mode. See “Defogging and Defrosting” later in
this section.
#(Normal Air Conditioning):Press this button to
turn the air conditioning system on or off. When this
button is pressed, an indicator light comes on to show
that the air conditioning is activated. Normal Air
Conditioning (A/C) can be selected in any mode as long
as the fan is on and the outside air temperature is above
freezing. Normal A/C cannot be selected at the same
time as Hybrid Air Conditioning (A/C). A ashing indicator
light indicates that the air conditioning compressor is
currently not available.When Normal A/C is selected, the climate control system
will prevent all automatic engine start/stop operations.
This will ensure the cabin comfort is maintained. See “Air
Conditioning and Automatic Engine Start/Stop” later in
this section.
N(Hybrid Air Conditioning):Press this button to
turn the Hybrid A/C system on or off. When this button is
pressed, an indicator light comes on to show that the
Hybrid A/C is activated. Hybrid A/C can be selected in
any mode, except defrost as long as the fan is on and the
outside air temperature is above freezing. Hybrid A/C
cannot be selected at the same time as the normal air
conditioning. A ashing indicator light indicates the air
conditioning compressor is not available.
The Hybrid A/C works to balance fuel economy and air
conditioning comfort. When Hybrid A/C is used in warm
weather, the vehicle gets better fuel economy by allowing
more frequent start/stops. For additional cooling, select
Normal A/C. See “Air Conditioning and Automatic Engine
Start/Stop” later in this section.
3-20
ProCarManuals.com

@(Recirculation):Press this button to toggle
between recirculate and outside air modes. The indicator
light turns on when the recirculate mode is selected.
This mode can be used to prevent outside air and odors
from entering the vehicle or to help cool the air inside
the vehicle more quickly. Avoid using the recirculation
mode during high periods of humidity and cool outside
temperatures since this may result in increased window
fogging. If window fogging is experienced, select the
defrost mode.
Recirculation mode is not available in oor, defog or
defrost modes. If the button is selected in these modes,
the indicator will ash. This helps prevent window fogging
and moisture building up inside the vehicle.
Defogging and Defrosting
Fog on the inside of windows is a result of high humidity
(moisture) condensing on the cool window glass. This
can be minimized if the climate control system is used
properly. There are two modes to clear fog or frost from
the windshield and side windows. Use the defog mode
to clear the windows of fog or moisture and warm the
passengers. Use the defrost mode to remove fog or frost
from the windshield more quickly. For best results, clear
all snow and ice from the windshield before defrosting.Manually turn the right knob to select the defog or
defrost mode.
-(Defog):This mode directs air to the windshield,
side window outlets and oor outlets. When this mode is
selected, the system turns the recirculation mode off and
runs the air conditioning compressor unless the outside
air is at or below freezing. The recirculation mode cannot
be selected while in defog mode. This helps prevent
window fogging and moisture building up inside the
vehicle.
0(Defrost):This mode directs most of the air to the
windshield, with some air directed to the side window
outlets and the oor outlets. When this mode is selected,
the system turns the recirculation mode off automatically
and runs the air conditioning compressor unless the
outside air is at or below freezing. The recirculation mode
cannot be selected while in defrost mode. This helps
prevent window fogging and moisture building up inside
the vehicle. In this mode, the climate control system
prevents all automatic engine start/stop operations.
This ensures the best defrost performance.
3-21
ProCarManuals.com

Rear Window Defogger
The rear window defogger uses a warming grid to
remove fog from the rear window.
The rear window defogger will only work when the
ignition is in ON/RUN.
<(Rear Window Defogger):Press this button to
turn the rear window defogger on or off. An indicator
light on the button comes on to show that the rear
window defogger is activated.
The rear window defogger stays on for about 10 minutes
if the vehicle remains at slower vehicle speeds or until
the button is pressed, or unless the ignition is turned
to ACC/ACCESSORY or LOCK/OFF. If turned on again,
the defogger only runs for about ve minutes before
turning off again. At higher vehicle speeds, the defogger
may stay on continuously. The defogger can always
be turned off by pressing the button again or by turning
off the ignition.
Notice:Do not use anything sharp on the inside
of the rear window. If you do, you could cut or
damage the warming grid, and the repairs would
not be covered by the vehicle warranty. Do not
attach a temporary vehicle license, tape, a decal
or anything similar to the defogger grid.
Air Conditioning and Engine Start/Stop
On hot days, use the automatic fan and automatic air
delivery mode settings and the vehicle will reach the
desired temperature more quickly. The desired fan and
air delivery mode settings can still be adjusted manually.
Open the windows to let the hot inside air escape, then
close them. This helps reduce the time it takes for the
vehicle to cool down and helps the system to operate
more efficiently.
When either the Normal A/C or Hybrid A/C modes are
active, the air conditioning system removes moisture
from the air, so a small amount of water may drip under
the vehicle while idling or after turning off the engine.
This is normal.
The use of Normal A/C causes the engine to keep
running while the vehicle is at a complete stop to allow
the climate control system to continue cooling.
The use of Hybrid A/C allows automatic engine start/
stop operations while the vehicle is at a complete stop.
The air conditioning compressor can not run when
the engine is not running, resulting in reduced cooling
performance. The climate control system may keep the
engine running or restart the engine during a stop to
continue cooling. Selecting the Normal A/C button forces
the engine and air conditioning compressor to restart
automatically. For more information about Engine
Start/Stop operation, seeStarting the Engine
(Automatic Engine Start/Stop) on page 2-18.
3-22
ProCarManuals.com

Compass Calibration
The compass can be manually calibrated. Only calibrate
the compass in a magnetically clean and safe location,
such as an open parking lot, where driving the vehicle
in circles is not a danger. It is suggested to calibrate
away from tall buildings, utility wires, manhole covers,
or other industrial structures, if possible.
If CAL should ever appear in the DIC display, the
compass should be calibrated.
If the DIC display does not show a heading, for
example, N for North, or the heading does not change
after making turns, there may be a strong magnetic eld
interfering with the compass. Such interference may be
caused by a magnetic CB or cell phone antenna mount, a
magnetic emergency light, magnetic note pad holder, or
any other magnetic item. Turn off the vehicle, move the
magnetic item, then turn on the vehicle and calibrate the
compass.To calibrate the compass, use the following procedure:Compass Calibration Procedure
1. Before calibrating the compass, make sure the
compass is set to the variance zone in which
the vehicle is located. See “Compass Variance
(Zone) Procedure” earlier in this section.
Do not operate any switches such as window,
sunroof, climate controls, seats, etc. during
the calibration procedure.
2. Press the reset stem until HOLD STEM TO
CALIBRATE COMPASS displays.
3. Press and hold the reset stem to start the compass
calibration.
4. The DIC will display CALIBRATING COMPASS:
TURN IN CIRCLES. Drive the vehicle in tight
circles at less than 5 mph (8 km/h) to complete
the calibration. The DIC will display COMPASS
CALIBRATION COMPLETE for a few seconds
when the calibration is complete. The DIC display
will then return to HOLD STEM TO CALIBRATE
COMPASS.
3-49
ProCarManuals.com

Before Leaving on a Long Trip
To prepare your vehicle for a long trip, consider having
it serviced by your dealer/retailer before departing.
Things to check on your own include:
Windshield Washer Fluid:Reservoir full?
Windows clean — inside and outside?
Wiper Blades:In good shape?
Fuel, Engine Oil, Other Fluids:All levels checked?
Lamps:Do they all work and are lenses clean?
Tires:Are treads good? Are tires inated
to recommended pressure?
Weather and Maps:Safe to travel?
Have up-to-date maps?
Highway Hypnosis
Always be alert and pay attention to your surroundings
while driving. If you become tired or sleepy, nd
a safe place to park your vehicle and rest.
Other driving tips include:
Keep the vehicle well ventilated.
Keep interior temperature cool.
Keep your eyes moving — scan the road ahead
and to the sides.
Check the rearview mirror and vehicle
instruments often.
Hill and Mountain Roads
Driving on steep hills or through mountains is different
than driving on at or rolling terrain. Tips for driving
in these conditions include:
Keep your vehicle serviced and in good shape.
Check all uid levels and brakes, tires, cooling
system, and transmission.
Going down steep or long hills, shift to a lower gear.
{CAUTION:
If you do not shift down, the brakes could get
so hot that they would not work well. You
would then have poor braking or even none
going down a hill. You could crash. Shift down
to let the engine assist the brakes on a steep
downhill slope.
4-16
ProCarManuals.com

You can run the engine to keep warm, but be careful.
{CAUTION:
Snow can trap exhaust gases under your
vehicle. This can cause deadly CO (carbon
monoxide) gas to get inside. CO could
overcome you and kill you. You cannot see
it or smell it, so you might not know it is in
your vehicle. Clear away snow from around
the base of your vehicle, especially any
that is blocking the exhaust pipe. And check
around again from time to time to be sure
snow does not collect there.
Open a window just a little on the side of the
vehicle that is away from the wind. This will
help keep CO out.
4-20
ProCarManuals.com

Run your engine only as long as you must. This
saves fuel. When you run the engine, make it go
a little faster than just idle. That is, push the accelerator
slightly. This uses less fuel for the heat that you
get and it keeps the battery charged. You will need
a well-charged battery to restart the vehicle, and
possibly for signaling later on with the headlamps.
Let the heater run for a while.
Then, shut the engine off and close the window
almost all the way to preserve the heat. Start the
engine again and repeat this only when you feel
really uncomfortable from the cold. But do it as little
as possible. Preserve the fuel as long as you can.
To help keep warm, you can get out of the vehicle
and do some fairly vigorous exercises every half
hour or so until help comes.If Your Vehicle is Stuck in Sand,
Mud, Ice, or Snow
Slowly and cautiously spin the wheels to free your
vehicle when stuck in sand, mud, ice, or snow. See
Rocking Your Vehicle to Get It Out on page 4-22.
If your vehicle has a traction system, it can often help
to free a stuck vehicle. Refer to your vehicle’s traction
system in the Index. If the stuck condition is too severe
for the traction system to free the vehicle, turn the
traction system off and use the rocking method.
{CAUTION:
If you let your vehicle’s tires spin at high
speed, they can explode, and you or others
could be injured. The vehicle can overheat,
causing an engine compartment re or other
damage. Spin the wheels as little as possible
and avoid going above 35 mph (55 km/h) as
shown on the speedometer.
For information about using tire chains on your vehicle,
seeTire Chains on page 5-66.
4-21
ProCarManuals.com

Wheel Alignment and Tire Balance..................5-64
Wheel Replacement......................................5-64
Tire Chains..................................................5-66
If a Tire Goes Flat........................................5-67
Tire Sealant and Compressor Kit....................5-68
Appearance Care............................................5-79
Interior Cleaning...........................................5-79
Fabric/Carpet...............................................5-80
Instrument Panel, Vinyl, and Other Plastic
Surfaces..................................................5-81
Care of Safety Belts......................................5-81
Weatherstrips...............................................5-82
Washing Your Vehicle...................................5-82
Cleaning Exterior Lamps/Lenses.....................5-82
Finish Care..................................................5-83
Windshield and Wiper Blades.........................5-84
Aluminum Wheels.........................................5-84
Tires...........................................................5-85Sheet Metal Damage.....................................5-85
Finish Damage.............................................5-85
Underbody Maintenance................................5-86
Chemical Paint Spotting.................................5-86
Vehicle Care/Appearance Materials..................5-86
Vehicle Identication......................................5-87
Vehicle Identication Number (VIN).................5-87
Service Parts Identication Label.....................5-88
Electrical System............................................5-88
Intermediate Voltage Devices and Wiring..........5-88
Add-On Electrical Equipment..........................5-89
Windshield Wiper Fuses................................5-89
Power Windows and Other Power Options.......5-89
Fuses and Circuit Breakers............................5-90
Instrument Panel Fuse Block..........................5-90
Underhood Fuse Block..................................5-93
Capacities and Specications..........................5-98
Section 5 Service and Appearance Care
5-2
ProCarManuals.com

If No Steam Is Coming From Your
Engine
If you get an engine overheat warning, but see or
hear no steam, the problem may not be too serious.
Sometimes the engine can get a little too hot when you:
Climb a long hill on a hot day.
Stop after high-speed driving.
Idle for long periods in traffic.
Tow a trailer.
If you get the overheat warning with no sign of steam,
try this for a minute or so:
1. If you have an air conditioner and it is on, turn it off.
2. Turn on your heater to full hot at the highest fan
speed and open the windows as necessary.
3. Try to minimize engine load. If you are in a traffic
jam, shift to NEUTRAL (N); otherwise, shift to the
highest gear possible while driving.If you no longer have the overheat warning, you can
drive. Just to be safe, drive slower for about ten minutes.
If the warning does not come back on, you can drive
normally.
If the warning continues and you have not stopped, pull
over, stop, and park your vehicle right away.
If there is still no sign of steam, idle the engine for
three minutes while you are parked. If the warning
continues, turn off the engine and get everyone out of
the vehicle until it cools down.
You may decide not to lift the hood but to get service
help right away.
5-24
ProCarManuals.com