warning Seat Alhambra 2010 Owner's Manual

Page 294 of 413

Checking and refilling levels293
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Checking and refilling levels
Filling the tank
Introduction
The fuel tank flap is on the rear right of the vehicle.
Additional information and warnings:
xFuel Ÿpage 297
xSelective Catalytic Reduction (AdBlue) Ÿpage 300
xWorking in the engine compartment Ÿpage 304
WARNING
Refuelling or handling fuel carelessly can cause an explosion or fire
resulting in serious burns and injuries.
xAlways make sure that you correctly close the fuel cap to avoid evapo-
ration and fuel spillage.
xFuels are highly explosive and inflammable substances that can cause
serious burns and injuries.
xFuel could leak out or be spilt if the engine is not switched off or if the
filler fuel nozzle is not fully inserted into the tank filler neck when refuel-
ling. This could lead to a fire, explosion and severe injuries.
xWhen refuelling, turn off the engine, the auxiliary heating
(Ÿpage 187) and turn off the ignition for safety reasons.
xAlways turn off mobile telephones, radio apparatus and other radio
wave emitting equipment before refuelling. Electromagnetic waves could
cause sparks and lead to a fire.
xNever enter the vehicle while refuelling. If it is absolutely necessary to
enter the vehicle, close the door and touch a metal surface before touching
the filler nozzle again. This will prevent the generation of static electricity.
Sparks could cause a fire when refuelling.
xNever handle fuel close to open flames, sparks or objects with slow
combustion (e.g. cigarettes).
xAvoid static electricity and electro-magnetic radiation when refuelling.
xObserve the safety regulations of the service station.
xNever spill fuel on the vehicle or in the luggage compartment.
WARNING
For safety reasons, SEAT does not recommend carrying a spare fuel canister
in the vehicle. Fuel could be spilled and catch fire, above all in case of an
accident and this applies to a full container as well as empty containers.
This could lead to explosions, fires and injuries.
xObserve the following if you exceptionally have to carry fuel in a
canister:
Never place a fuel container to fill it inside the vehicle or on the
vehicle, for example, in the luggage compartment or on the tailgate.
Filling in these circumstances could create an electrostatic charge and
spark that could ignite fuel fumes.
Always place the canister on the ground to fill it.
Insert the fuel nozzle into the mouth of the canister as far as
possible.
If you are using a metal fuel canister, the nozzle must always touch
the canister while it is being filled to avoid static electricity.
WARNING (continued)

Page 295 of 413

Checking and refilling levels 294
Follow the legal requirements for the use, storage and transport of
spare fuel canisters.
Insure that the fuel container complies with manufacturing stand-
ards, for example, ANSI or ASTM F852-86.
Caution
xAlways remove any fuel spilled on the vehicle paintwork immediately to
avoid damage to the wheel housing, the tyre and vehicle paintwork.
xRefuelling a petrol engine with diesel or a diesel engine with petrol can
cause serious engine and fuel system damage; the resulting malfunctions
are not covered by the SEAT warranty. If you refuel with the wrong type of fuel,
never start the engine. This applies to even the smallest amount of the wrong
fuel. You should obtain professional assistance. With the engine running, the
composition of the wrong fuel could significantly damage the fuel system and
the engine itself.
xIn vehicles with a diesel engine, under no circumstances should you
refuel or drive with petrol, kerosene, heating oil or any other type of different
fuel. Other types of fuels could cause serious damage to the engine and to
the fuel supply system and the resulting problems are not covered by the
SEAT warranty.
For the sake of the environment
Fuels can contaminate the environment. Collect any spilt service fluids and
allow a professional to dispose of them.
Note
There is no emergency mechanism for the manual release of the tank flap. If
necessary, request assistance from specialised personnel.
Control lamps and fuel gauge
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
The auxiliary heater and the auxiliary heater running off petrol will automati-
cally switch off when the indicator
z or  lights.
WARNING (continued)
lights upGauge position
Ÿfig. 169Possible cause ŸSolution
Red mark
(arrow)
The fuel tank is almost
empty.
The reserve tank is
being used
Ÿpage 392.
Refuel as soon as
possible Ÿ.
§Fuel tank not closed
correctly.Stop the vehicle and
close the tank flap
properly.
Fig. 169 On the instru-
ment panel: Fuel gauge for
petrol and diesel.

Page 296 of 413

Checking and refilling levels295
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
WARNING
Driving with insufficient fuel reserve could result in the vehicle breaking
down in traffic and a serious accident.
xIf the fuel level is too low then the fuel supply to the engine can become
irregular especially on slopes.
xIf the engine “is choked” or stalls due to lack of or irregularity of the
fuel supply, the power steering as well as all of the driver assistance
systems including braking assistance will stop working.
xAlways refuel when there is only one quarter of the fuel tank left to
avoid running out of fuel.
Caution
xAlways pay attention to any lit lamps and to the corresponding descrip-
tions and instructions to avoid damage to the vehicle.
xNever run the tank completely dry. An irregular fuel supply may lead to
ignition faults and unburnt fuel could enter the exhaust system. This could
damage the catalytic converter filter or the diesel particulate filter!
Note
The arrow next to the fuel pump symbol on the instrument panel Ÿpage 294,
fig. 169 indicates the side of the vehicle on which the tank flap is located.
Filling the tank with petrol or diesel
Before refuelling, always turn off the engine, the ignition, mobile telephones,
auxiliary heating and keep them off during refuelling.
Unscrewing the tank cap
xThe tank flap is at the rear of the vehicle on the right.
xPress the rear of the tank flap to open it.
xUnscrew the tank cap anti-clockwise and insert it in the hole in the tank
flap hinge Ÿfig. 170.
Refilling
The correct petrol type for the vehicle is located on a sticker inside the fuel
tank flap Ÿpage 297.
xIf the automatic filler nozzle is operated correctly, it will switch itself off as
soon as the tank is full Ÿ.
xDo not continue to refuel if it is turned off! Otherwise, this will fill the
expansion chamber and fuel may leak out if the ambient conditions are warm.
Fig. 170 Open tank flap
with tank cap attached to
the holder.

Page 297 of 413

Checking and refilling levels 296
Closing the tank cap
xScrew on the tank cap clockwise until it you hear it click into position.
xPress the tank flap until you hear it click into place. The tank flap must be
flush with the body contour.
WARNING
Do not continue refilling once the fuel nozzle has switched itself off. The
fuel tank may be filled too much. As a result, fuel may spurt out and spill.
This could lead to a fire, explosion and severe injuries.
Caution
xAlways remove any fuel spilled on the vehicle paintwork immediately to
avoid damage to the wheel housing, the tyre and vehicle paintwork.
For the sake of the environment
Spilt fuel can contaminate the environment.
Refilling precautions
Information on bulb replacement Ÿpage 360.
Checklist
Never work on the engine or in the engine compartment if you are not familiar
with the operations to be carried out, the applicable safety standards and
especially if you do not have the instruments, liquids and tools necessary
Ÿpage 304, “Working in the engine compartment”! Have the work carried
out by a qualified workshop if you are uncertain. Check the following regu-
larly, preferably when you refuel:
xWindscreen washer fluid level Ÿpage 124
xEngine oil level Ÿpage 309
xEngine coolant level Ÿpage 313
xBrake fluid level Ÿpage 210
xTyre pressure Ÿpage 323
xVehicle lighting required to guarantee road safety:
–Indicators
– Side lights, dipped headlights and full beam headlights
– Rear lights
–Brake lights
– Rear fog light Ÿpage 116
WARNING
Not following the checklist prepared for your own safety could lead to acci-
dents and severe injuries.
xAlways follow the check list and perform the necessary operations.

Page 298 of 413

Checking and refilling levels297
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Fuel
Introduction
You will find a factory-fitted sticker containing information on the type of fuel
for your vehicle on the inside of the fuel tank flap.
Additional information and warnings:
xŸBooklet “Maintenance Programme”
xRefuelling Ÿpage 293
xEngine and exhaust system management Ÿpage 255
WARNING
Refuelling or handling fuel carelessly can cause an explosion or fire
resulting in serious burns and injuries.
xFuel is a highly explosive, easily flammable substance.
xObserve current safety instructions and local regulations concerning
the handling of fuel.
Types of fuel
The type of fuel to use when refilling will depend on the vehicle's engine. You
will find a factory-fitted sticker containing information on the type of fuel for
your vehicle on the inside of the fuel tank flap.
SEAT recommends the use of sulphur-free or low sulphur fuel to reduce
consumption and prevent engine damage.
Petrol
Petrol types
Vehicles with petrol engines must refuel using unleaded petrol according to
European norm EN 228 Ÿ.
Petrol types are categorised according to their octane number (e.g. 91, 95, 98
or 99 RON (RON = “Research Octane Number”). You may use petrol with a
high octane number than the one recommended for your engine. However,
this has no advantage in terms of fuel consumption and engine power.
SEAT recommends refuelling with a low sulphur content or sulphur-free petrol
to reduce petrol consumption for petrol engines.
Petrol additives
The quality of the fuel influences running behaviour, performance and service
life of the engine. For this reason, you should use good quality petrol
containing a mixture of additives. These additives will help to prevent corro-
sion, keep the fuel system clean and prevent deposits from building up in the
engine.
Possible types of
fuelAlternative namesFurther information
91a) RON
a)RON = Regulation Octane Number
Normal petrol, normal
unleaded petrol
Ÿpage 29795a) RONPremium unleaded petrol (95
RON)
98a) RONPremium unleaded petrol (98
RON)
DieselŸpage 298

Page 300 of 413

Checking and refilling levels299
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a Whenever there is little fuel in the tank (reserve), the auxiliary heater auto-
matically switches off.
WARNING
Never use start boosters. An aerosol start booster could explode or cause
a sudden rise in engine speed leading to engine damage and serious injury.
Caution
xThe vehicle is not prepared for the use of biodiesel. Under no circum-
stances should this fuel be used. It could damage the fuel system and subse-
quently lead to engine faults!
xThe addition of biodiesel to diesel by the diesel producer according to
Standard EN 590 or other equivalent (DIN 51628 in Germany, for example) is
authorised and causes no type of damage to the engine or the fuel system.
xThe diesel engine has been designed for to use diesel fuel exclusively.
Therefore, never use petrol, fuel oil or other unsuitable fuels. The composition
of these fuels may significantly damage the fuel system and the engine.
xThe use of diesel fuels with a high sulphur percentage could considerably
reduce the service life of the diesel particulate filter. Your qualified workshop
will be able to tell you which countries have diesel with a high sulphur
content.
Information on fuel consumption
The consumption and emission values indicated do not refer to one specific
vehicle. They are only to be used to compare the values of the different
vehicle versions. The fuel consumption and CO
2 emissions of a vehicle not
only depend on the effective use of fuel. They also depend on your driving
style and other non-technical factors.Calculating fuel consumption
Fuel consumption and emission values are determined according to the
current version of the 715/2007/EC or 80/1268/EEC regulation and are valid
for the vehicle kerb weight. The specifications do not refer to an individual
vehicle. Two measuring cycles are carried out on a rolling road test bed. The
test criteria are as follows:
Note
The kerb weight may vary according to the vehicle equipment. This could
raise consumption and the CO
2 emissions slightly.
Note
In practice, consumption values could be different to the values calculated
based on the 715/2007/EC or 80/1268/EEC regulations.
Urban cycleMeasurement of the urban cycle starts with an engine cold
start. City driving is then simulated at between 0 and 50
km/h.
Road cycleIn the road cycle simulation, the car undergoes frequent
acceleration and braking in all gears, as in normal everyday
driving. The road speed ranges from 0 to 120 km/h.
CombinedThe average combined consumption is calculated with a
weighting of around 37 % for the urban cycle and 63 % for
the road cycle.
CO2 emis-
sions of the
combination The exhaust gases are collected during both driving cycles to
calculate carbon dioxide emissions (urban and road). The
gas composition is then analysed to evaluate the CO
2 con-
tent and other emissions.

Page 301 of 413

Checking and refilling levels 300
Selective Catalytic Reduction* (AdBlue)
Introduction
The AdBlue fill level must be checked when the vehicle is being serviced
ŸBooklet “Maintenance Programme”.
Additional information and warnings:
xLuggage compartment Ÿpage 146
xFuel Ÿpage 297
xWheels and tyres Ÿpage 323
xAccessories, parts replacement, repairs and modifications Ÿpage 285
WARNING
If the AdBlue fill level is too low, the vehicle may not restart after switching
the ignition off. The emergency start or jump start will not be possible
either!
xTop up with AdBlue at the latest 1000 km or 600 miles before it runs
out.
xDo not allow the AdBlue to run too low.
WARNING
AdBlue is an irritant, corrosive liquid that can cause injuries if it touches
the skin, eyes or respiratory organs.
xIf AdBlue get in contact with eyes and skin, rinse for at least 15 minutes
with plenty of water and seek medical help.
xIf the AdBlue is swallowed, wash the mouth with plenty of water for at
least 15 minutes. Do not try to provoke vomiting unless recommended by a
Doctor. Seek medical advice immediately.
Caution
AdBlue damages surfaces such as painted vehicle parts, plastic, items of
clothing and carpets. Spilt AdBlue should be removed as quickly as possible
using a damp cloth and plenty of cold water.
xIf the AdBlue has crystallised, remove with warm water and a sponge.
Control and warning lamps
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
lights upPossible cause ŸSolution
b (red)The engine cannot be
restarted! The level of AdBlue
is too low.Stop the vehicle in a suitable,
safe and flat area then top up
with the minimum quantity of
AdBlue required Ÿpage 302.
b (red)
with
>
The engine cannot be
restarted! AdBlue system
malfunction.Contact a specialist workshop.
Have the system checked there.
b (yel-
low)The AdBlue reserve is low.
Refill AdBlue over the next kilo-
metres or miles as indicated
Ÿpage 302. SEAT recommends
contacting a specialist work-
shop.
b (red)
with

>
There is a fault in the AdBlue
system or unsuitable AdBlue
fluid has been used.Contact a specialist workshop.
Have the system checked there.

Page 302 of 413

Checking and refilling levels301
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
WARNING
If the warning lamps and messages are ignored, the vehicle may stall in
traffic, or may cause accidents and severe injuries.
xNever ignore the warning lamps or text messages.
xStop the vehicle safely as soon as possible.
Caution
Failure to heed the warning lamps and text messages when they appear may
result in faults in the vehicle.
Information on AdBlue
In vehicles with Selective Catalytic Reduction, a special urea solution
(AdBlue) is injected into the exhaust gas system in front of the catalytic
converter to reduce nitrogen oxide emissions.
The consumption of AdBlue depends on individual driving style, the temper-
ature at which the system operates and the outside temperature where the
vehicle is driven.
AdBlue is kept in an independent tank in the vehicle and should be refilled at
an official supplier. The AdBlue tank holds about 17 litres.
A message will be displayed on the instrument panel around 2400 km before
the next service to indicate that AdBlue must be refilled Ÿpage 302. If you
ignore this message and do not refill, you will be unable to start the engine
afterwards Ÿpage 300.
SEAT recommends contacting a specialist workshop. If you are unable to visit
a qualified specialist workshop, you should temporarily refill with a minimum
of 10.0 litres of AdBlue. Only refill using AdBlue expressly approved by SEAT.When the indicators
b and > light simultaneously, there is a fault. SEAT
recommends visiting the closest qualified workshop.
AdBlue
® is a registered trademark in the US, Germany, the European Union
and other countries belonging to the German automobile industry ("Verband
der Automobilindustrie e. V.", VDA).

Page 304 of 413

Checking and refilling levels303
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xRotate the shut off on the cover clockwise Ÿpage 302, fig. 171 and open
the cover forwards.
xUnscrew the tank filler neck cap Ÿpage 302, fig. 172 anticlockwise.
Refilling AdBlue
Only use AdBlue that is approved by SEAT and that complies with the ISO
22241-1 Standard. Only use genuine bottles.
xObserve the instructions and information provided by the refill bottle
manufacturer.
xObserve the expiry date.
xUnscrew the cap on the refill bottle.
xPlace the refill bottle upside down inside the tank filler neck.
xPress the refill bottle against the filler neck and keep in this position.
xAdd at least 10 litres of AdBlue (6 bottles). A lower quantity would be
insufficient.
xWait until the contents of the refill bottle have been poured into the
AdBlue tank. Do not crush or damage the bottle!
xUnscrew the liquid bottle anticlockwise and remove it carefully Ÿ.
xYou can tell when the AdBlue tank is full because the bottle will be empty.
Closing the tank filling neck
xScrew on the tank filler neck cap Ÿpage 302, fig. 172 clockwise until
it is fully inserted.
xPlace the cover and turn the shut off anticlockwise to close it.
Operations before driving
xOnly switch the ignition on after refilling.
xKeep the ignition switch on for at least 30 seconds so that the system
detects tank refilling.
xWait 30 seconds before starting the engine!
WARNING
Only keep AdBlue in its original container, tightly shut and in a safe place.
xNever keep AdBlue in empty food cans, bottles or other containers to
avoid other people mistaking it for something else.
xKeep the AdBlue out of the reach of small children.
Caution
xOnly refill using AdBlue expressly approved by SEAT. The use of any other
type of AdBlue could cause engine damage!
xAdBlue should never be mixed with water or any other additives. Any type
of damage caused by a mixture will not be covered by the warranty.
xDo not add AdBlue to the diesel fuel tank! Otherwise you may damage the
engine.
xNever leave the refill bottle in the vehicle. It could become permeable due
to temperature changes and bottle damage and the AdBlue could damage
the vehicle interior.
For the sake of the environment
Dispose of the refill bottle in an environment-friendly manner.
Note
Suitable AdBlue refill bottles can be purchased from a qualified workshop.
A1
A2
A1

Page 305 of 413

Checking and refilling levels 304
Working in the engine compartment
Introduction
Before working in the engine compartment, make sure that the vehicle is
parked on horizontal and firm ground.
The engine compartment of the vehicle is a hazardous area. Never work on
the engine or in the engine compartment if you are not familiar with the oper-
ations to be carried out, the applicable safety standards and especially if you
do not have the instruments, liquids and tools necessary Ÿ! Have the
work carried out by a qualified workshop if you are uncertain. Negligent work
can cause serious injury.
Additional information and warnings:
xWindscreen wash system Ÿpage 124
xStart and stop the engine Ÿpage 195
xBrake fluid Ÿpage 210
xVehicle battery Ÿpage 318
xChecks when filling up Ÿpage 293
xEngine oil Ÿpage 309
xEngine coolant Ÿpage 313
xAccessories, parts replacement, repairs and modifications Ÿpage 285
WARNING
If the vehicle moves unexpectedly, this could cause serious injury.
xNever work underneath the vehicle if it is not secured against moving.
If you must work underneath the vehicle with the wheels in contact with
the ground then it should be parked on flat ground, the wheels should be
prevented from moving and the key must be removed from the ignition.
xIf you have to work underneath the vehicle, you must use suitable
stands additionally to support the vehicle, there is a risk of accident!. The
jack is not intended for this kind of work and its failure could lead to severe
injuries.
WARNING
The engine compartment is a dangerous area capable of causing serious
injury.
xFor all type of work, always take the utmost precautions, work carefully
and note the general safety standards in force. Never take personal risks.
xNever work on the engine or in the engine compartment if you are not
familiar with the necessary operations. If you are not sure about proce-
dures then visit a qualified workshop to carry out the necessary work.
Incorrect work can cause serious injuries.
xNever open the bonnet if you see steam or coolant escaping from the
engine compartment. Hot vapours and coolant can cause serious burns.
Always wait until you cannot see or hear the sound of steam or coolant
coming from the engine compartment.
xAlways allow the engine to cool down before opening the bonnet.
xContact with hot elements of the engine and the exhaust system can
cause burns.
xOnce the engine has cooled, follow the instructions below before
opening the bonnet:
Turn on the electronic parking brake and place the gear selector lever
in P or the gear stick in neutral.
Remove the key from the ignition.
Keep children away from the engine compartment and never leave
them unsupervised.
WARNING (continued)

Page:   < prev 1-10 ... 161-170 171-180 181-190 191-200 201-210 211-220 221-230 231-240 241-250 ... 280 next >