warning Seat Alhambra 2010 Owner's Manual

Wheels and tyres 330
are equally spaced around the tyre tread. Certain marks on the tyre walls (for
example, the letters “TWI” or other symbols) indicate the position of the wear
indicators.
Tread wear indicators indicate if a tyre is worn. Tyres must always be replaced
before the tyre tread has worn to the level of the indicator.
WARNING
Driving with worn tyres is dangerous, and may lead to loss of control of the
vehicle with serious consequences.
xTyres must be replaced before the wear indicators are at the same level
as the tread pattern.
xWorn tyres have significantly reduced grip, especially on wet surfaces,
increasing the risk of “aquaplaning”.
xWorn tyres make control of the vehicle more difficult in normal or diffi-
cult driving conditions, increasing the braking distance and the risk of
skidding.
Damaged tyres
Damage to wheels and tyres is often not immediately visible. If you notice
unusual vibration or the car pulling to one side, this may indicate that one of
the tyres is damaged Ÿ.
xSlow down immediately if you think you have a damaged wheel.
xCheck the wheels and tyres for damage.
xIf tyres are worn, stop driving and seek qualified assistance.
xIf there is no visible exterior damage, drive slowly and carefully to the
nearest qualified workshop and have the vehicle checked.Foreign bodies in the tyre
xDo not remove foreign bodies if they have penetrated through the tyre
wall!
xYou should obtain professional assistance immediately.
The sealant at the lower part of the tyre tread wraps around the foreign body
and provisionally seals the tyre.
Wear of tyres
The wear of tyres depends on a number of factors, for example:
xDriving style.
xUnbalanced wheels.
xRunning gear settings.
Driving style: driving round bends fast or sudden acceleration or braking
speed up the wear of tyres. When the driving style is normal, if the tyres wear
too quickly, have the running gear settings checked at a qualified workshop.
Wheel run-out: The wheels on new vehicles are balanced. However, certain
circumstances may lead to imbalance (run-out), which is detected as vibra-
tions in the steering wheel. Run-out leads to wear of the steering and suspen-
sion. In the event of run out, the wheels should be balanced again. When a
new wheel is fitted, it should be balanced again.
Running gear settings: an incorrectly positioned running gear increases the
wear of tyres and affects your safety while driving. If tyres wear too quickly,
have the wheel alignment checked at a specialist workshop.
WARNING
If you notice unusual vibration or the car pulls to one side while driving,
this may indicate that one of the tyres is damaged.
xReduce speed immediately and stop, while observing the highway
code.
xCheck the wheels and tyres for damage.

Wheels and tyres331
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xNever carry on driving on worn tyres or wheels. Request qualified
assistance immediately.
xIf there is no visible exterior damage, drive slowly and carefully to the
nearest qualified workshop and have the vehicle checked.
Winter tyres
In winter conditions winter tyres will considerably improve the vehicles
handling. The design of summer tyres (width, rubber compound, tread
pattern) gives less grip on ice and snow. SEAT strongly recommends using
winter tyres or all year round tyres on all four wheels of the vehicle, especially
if you expect to drive in wintery weather. Winter tyres also improve the vehicle
braking performance, reducing the braking distance in winter weather. SEAT
recommend that winter tyres be fitted to the vehicle at temperatures below
+7 °C (+45 °F).
The performance of winter tyres is much reduced if the tyre tread is worn
below 4 mm (1/16 inch). The age of the tyre is another factor affecting
performance, regardless of the depth of the tyre tread.
Please observe the following when using winter tyres:
xObserve legal requirements in each country.
xWinter tyres must be fitted on all four wheels.
xOnly use winter tyres in wintery weather conditions.
xOnly use winter tyres of the size authorised for the vehicle.
xOnly use radial winter tyres of the same type, size (rolling circumference)
and tread pattern.
xAdjust speeds to within the limits indicated (code letter on tyre) Ÿ.Speed limit
A code letter indicating the speed limit is stamped on all winter tyres
Ÿpage 334.
In some vehicles, it is possible to set a speed warning in the MFA
(multifunction indicator) menu on the instrument panel Ÿpage 70.
If you use V-rated tyres the speed limits and tyre pressure will be determined
by engine size. Please ask your SEAT qualified workshop for further informa-
tion on the maximum permitted speed and the required pressures for the
tyres.
All-wheel drive
Thanks to its all-wheel drive, your car will have plenty of traction in winter
conditions, even with the standard tyres. Nevertheless, SEAT still recommend
that winter tyres or all-season tyres should be fitted on all four wheels when
winter road conditions are expected, mainly because this will give a better
braking response.
Please observe all instructions and warnings when using snow chains
Ÿpage 332.
WARNING
Although winter tyres help to make driving safer in the winter, you should
not take unnecessary risks.
xAdjust your speed and driving style to visibility, road, traffic and
weather conditions.
xNever exceed the maximum permitted speed or loads specified for the
type of winter tyre fitted on your vehicle.
For the sake of the environment
When winter is over, change back to summer tyres. In temperatures above
+7 °C (+45 °F), performance will be improved if summer tyres are used. Fuel
consumption, wear and noises while driving will all be reduced.
WARNING (continued)

Wheels and tyres 332
Note
If the vehicle is fitted with a tyre control system, this should be “repro-
grammed” whenever a tyre is changed Ÿpage 248.
Note
Please ask at SEAT qualified workshops for information about the permitted
sizes for winter tyres.
Snow chains
When using snow chains, applicable local legislation and maximum
permitted speed limits must be observed.
In winter weather, snow chains not only help to improve grip but also improve
the braking capacity.
Snow chains must only be mounted on the front wheels, even on all-wheel
drive vehicles, and only with the tyre and rim combinations listed below:
SEAT recommends you ask a SEAT qualified workshop for further information
on wheel, tyre and chain sizes.
Wherever possible use fine-link chains measuring less than 15 mm (37/64
inch) including the lock.
Remove wheel hub covers and trim rings before fitting snow chains Ÿ.
The wheel bolts should be covered with caps for safety reasons. These are
available from qualified workshops.
WARNING
The use of unsuitable or incorrectly fitted chains could lead to serious acci-
dents and damage.
xAlways the appropriate snow chains.
xObserve the fitting instructions provided by the snow chain manufac-
turer.
xNever exceed the maximum permitted speeds when driving with snow
chains.
Caution
xYou must remove the snow chains to drive on roads which are free of
snow. Otherwise they will impair handling, damage the tyres and wear out
very quickly.
xWheel rims may be damaged or scratched if the chains come into direct
contact with them. SEAT recommends the use of covered snow chains.
Note
Snow chains are available in different sizes according to the vehicle type.Tyre sizeWheel rim
205/60 R166 1/2 J x 16 ET 33
215/60 R166 1/2 J x 16 ET 33

Wheels and tyres 336
Wheel trims*
Introduction
Additional information and warnings:
xCaring for and cleaning the vehicle exterior Ÿpage 269
xChange wheel Ÿpage 339
xVehicle tools Ÿpage 353
WARNING
If the wheel trims are not appropriate or not fitted correctly, they could
cause major accidents or damage.
xIncorrectly mounted wheel trims may come off while driving and
endanger other road users.
xDamaged trims must never be mounted on the wheels.
xAlways ensure that the brake ventilation and cooling is not cut off or
blocked. This is also valid if hubcaps are fitted later. If there is not enough
air, you may require significantly longer braking distances.
Caution
Remove and remount wheel trims taking care to avoid damage to the
vehicle.
Hubcaps
Depending upon the version, the hubcap is removed by pulling it Ÿfig. 186,
or by unscrewing it Ÿfig. 187.
Fig. 186 Removing the
hub cap.
Fig. 187 Remove the
hubcap by turning it
outwards.

Wheels and tyres339
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Changing a wheel*
Introduction
The tyres mounted on the vehicle are anti-puncture. The wheels should only
be changed when switching from summer to winter tyres or vice-versa. The
tools required for changing a wheel are only supplied with the vehicle if the
vehicle is supplied from the factory with winter tyres. If this is not the case,
please take the vehicle to a specialised workshop to have the wheels
changed.
You should only change the wheels yourself if the vehicle is parked in a safe
place, you are familiar with the procedure and you have all the necessary
tools! Otherwise, you should seek professional assistance.
Additional information and warnings:
xVehicle key set Ÿpage 78
xWheels and tyres Ÿpage 323
xWheel trims Ÿpage 336
xVehicle tools Ÿpage 353
WARNING
Changing a wheel can be dangerous, especially on the hard shoulder.
Please observe the following rules to minimise the risk of injury:
xStop the vehicle safely as soon as possible. Park your vehicle as safe
distance from surrounding traffic to change a wheel.
xWhen changing a wheel, keep all passengers and particularly children
a safe distance away from the work area.
xTurn on the hazard warning lights to warn other road users.
xEnsure the ground on which you park is flat and solid. If necessary,
support the jack on a wide solid base.
xIf you are changing a wheel yourself, you should be familiar with the
required procedure. Otherwise, you should seek professional assistance.
xOnly use suitable tools that are not damaged when changing a wheel.
xAlways stop the engine, turn on the electronic parking brake and place
the gear selector lever in position P, for an automatic gearbox, or engage a
gear for a manual gearbox to reduce the risk of the vehicle moving acciden-
tally.
xHave the tightening torque of the wheel bolts checked as soon as
possible with a reliable torque wrench.
Preparations for changing a wheel
Check list
Before changing a wheel, complete the following operations in the order
given Ÿ:
1. Park the vehicle on an even and solid surface.
2. Connect the electronic parking brake Ÿpage 210.
3. Automatic gearbox: Move selector lever to position P Ÿpage 201.
4. Stop the engine and remove the key from the ignition Ÿpage 195.
5. Manual gearbox: Select a gear Ÿpage 201.
6. Have all vehicle occupants get out of the vehicle and wait in a safe place
(for example, behind the safety barrier).
7. Block the opposite wheel with two folding wedges taken from the vehicle
tool kit Ÿpage 354, fig. 208 or similar objects.
8. When towing a trailer: unhook the trailer from the towing vehicle and
park it correctly.
9. If the luggage compartment is full: take the baggage out of the vehicle.
WARNING (continued)

Wheels and tyres 340
10. Take the vehicle tool kit out of the luggage compartment.
11. Remove the wheel trims Ÿpage 336.
WARNING
Failure to follow the checklist prepared for your own safety could lead to
accidents and severe injuries.
xAlways complete the operations given in the checklist and observe the
general rules of safety.
Wheel bolts
Only use the tool supplied with the vehicle to loosen the wheel bolts.
Loosen the wheel bolts only about one turn before raising the vehicle with the
jack.
If the wheel bolt is very tight, you may be able to loosen it by pushing down
on the end of the wheel brace carefully with your foot. Hold on to the car for
support and take care not to slip.
Loosening wheel bolts
xFit the wheel brace as far as it will go over the wheel bolt Ÿfig. 190.
xHold the wheel brace at the end and rotate the bolt approximately one
turn anticlockwise Ÿ.
Loosening anti-theft wheel bolts
For wheels with full hubcap, the anti-theft wheel lock must be threaded into
position Ÿfig. 191 or before mounting the hubcap. Otherwise it will
not be possible to mount the full hubcap.
xTake the adapter for anti-theft wheel bolts out of the vehicle tool kit.
xInsert the adapter onto the wheel bolt.
Fig. 190 Changing the
wheel: Slacken the wheel
bolts.
Fig. 191 Changing the
wheel: Tyre valve and
position of anti-theft
wheel locking bolt or
.A1
A2A3
A2A3

Wheels and tyres341
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xFit the wheel brace onto the adapter as far as possible.
xHold the wheel brace at the end and rotate the bolt approximately one
turn anticlockwise Ÿ.
Important information about wheel bolts
The wheel rims and bolts have been designed to be fitted to factory options.
If different rims are fitted, the correct wheel bolts with the right length and
correctly shaped bolt heads must be used. This ensures that wheels are fitted
securely and that the brake system functions correctly.
In some circumstances, wheel bolts from the same model vehicle should not
be used.
Wheel bolt tightening torque
The prescribed tightening torque for wheel bolts for steel and alloy wheels is
140 Nm. Have the tightening torque of the wheel bolts checked as soon as
possible with a reliable torque wrench.
If wheel bolts are rusty and it is difficult to tighten them, the threads should
be replaced and cleaned before checking the torque.
Never grease or lubricate wheel bolts or the wheel hub threads. Although
they have been tightened to the prescribed torque, they could come loose
while driving.
WARNING
If the wheel bolts are not fitted correctly they could be released while
driving leading to loss of vehicle control and serious damage.
xOnly use wheel bolts which correspond to the wheel rims in question.
xNever use different wheel bolts.
xThe bolts and threads should be clean, free of oil and grease and easy
to thread.
xTo loosen and tighten the wheel bolts, always use the wheel brace
supplied with the vehicle.
xLoosen the wheel bolts only about one turn before raising the vehicle
with the jack.
xNever grease or lubricate wheel bolts or the wheel hub threads.
Although they have been tightened to the prescribed torque, they could
come loose while driving.
xNever loosen the bolted joints of wheel rims with bolted ring trims.
xIf the wheel bolts are not tightened to the correct torque, they may
come loose while driving, and the bolts and rims may come out. If the tight-
ening torque is too high, the wheel bolts and threads can be damaged.
WARNING (continued)

Wheels and tyres343
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a Raise the vehicle using only the designated jacking points.
Check list
For your own safety and that of other passengers, the following points should
be observed in the order given Ÿ:
1. Select a suitable flat and firm surface for raising the vehicle.
2. Switch off the engine, engage a gear (manual gearbox) or place the
selector lever in position P Ÿpage 201 and turn on the electronic
parking brake Ÿpage 210.
3. When towing a trailer: unhook the trailer from the towing vehicle and
park it correctly.
4. Loosen the wheel bolts on the wheel to be changed Ÿpage 340.
5. Look below the vehicle for the jacking point Ÿpage 342, fig. 192
closest to the tyre which has to be changed.
6. Raise the jack with the handle until it can be inserted below the jacking
point.
7. Ensure that the foot of the jack is firmly on the ground and that it is
placed immediately below the lifting point on the vehicle Ÿpage 342,
fig. 193.
8. Straighten the jack and continue raising it using the handle until the claw
holds the vertical reinforcement beneath the vehicle Ÿpage 342,
fig. 193.
9. Raise the vehicle until the wheel is clear of the ground.
WARNING
If the vehicle is not correctly raised, it could fall off the jack causing serious
injury. Please observe the following rules to minimise the risk of injury:
xYou should only use a jack approved by SEAT for your vehicle. Other
jacks, even those approved for other SEAT models, might slip out of place.
xThe ground should be firm and flat. If the ground is sloped or soft then
the vehicle could slip and fall off the jack. If necessary, support the jack on
a wide solid base.
xIf the ground is slippery (for example, on tiles), place a non-slip surface
(for example a floor mat) beneath the jack to avoid slipping.
xOnly fit the jack at the prescribed jacking points. The claw of the jack
should grip the reinforcement nerve on the underbody Ÿpage 342,
fig. 193.
xYou should never have any limbs beneath a raised vehicle which is only
supported by a jack.
xIf you have to work underneath the vehicle, you must use suitable
stands additionally to support the vehicle, there is a risk of accident!.
xNever raise the vehicle if it is tilting to one side or the engine is running.
xNever start the engine when the vehicle is raised. The vehicle may come
loose from the jack due to the engine vibrations.
WARNING
Failure to follow the checklist prepared for your own safety could lead to
accidents and severe injuries.
xAlways complete the operations given in the checklist and observe the
general rules of safety.
WARNING (continued)

Wheels and tyres 344
Changing a wheel
Removing the wheel
xPlease observe the check list Ÿpage 339.
xLoosen the wheel bolts Ÿpage 340.
xJacking up the vehicle Ÿpage 342.
xUsing the hexagonal socket in the wheel brace Ÿfig. 194, unscrew the
slackened wheel bolts and place them on a clean surface.
xTake off the wheel.
Putting on the spare wheel
Check the direction of rotation of the tyre Ÿpage 325.
xFit the wheel.
xScrew on the anti-theft locking bolt with the adapter in position
Ÿpage 340, fig. 191 or clockwise and tighten gently.
xReplace the other wheel bolts and tighten slightly using the hexagonal
socket on the end of the wheel brace.
xLower the car with the jack.
xTighten all of the wheel bolts clockwise Ÿ. Tighten the bolts in diag-
onal pairs (not in a circle).
xPut the caps, trim or full hubcap back on Ÿpage 336.
WARNING
If the wheel bolts are not treated suitably or not tightened to the correct
torque then this could lead to loss of vehicle control and to a serious acci-
dent.
xAll the wheel bolts and hub threads should be clean and free of oil and
grease. The wheel bolts should be easily tightened to the correct torque.
xThe hexagonal socket in the wheel brace should be used for turning
wheel bolts only. Do not use it to loosen or tighten the wheel bolts.
After changing the wheel
xClean the wheel brace, if necessary and put it away in the luggage
compartment Ÿpage 353.
xHave the tightening torque of the wheel bolts checked as soon as
possible with a torque wrench Ÿpage 341.
Note
If the vehicle is fitted with a tyre monitoring system, this should be “repro-
grammed” if necessary whenever a tyre is changed Ÿpage 248.
Fig. 194 Changing the
wheel: loosen wheel bolts
with the socket at the end
of the wheel brace.
A2A3

If and when345
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
If and when
In case of emergency
Introduction
Additional information and warnings:
xBraking, stopping and parking Ÿpage 210
xEmergency locking and unlocking Ÿpage 348
xVehicle tools Ÿpage 353
WARNING
A faulty vehicle in traffic represents a risk of accident for the driver and for
other road users.
xStop the vehicle safely as soon as possible. Park the vehicle a safe
distance from surrounding traffic to lock all the doors in case of an emer-
gency. Turn on the hazard warning lights to warn other road users.
xNever leave children or disabled people alone in the vehicle if the doors
are to be locked. In case of an emergency, passengers will be trapped
inside the vehicle. Individuals locked in the vehicle can be exposed to very
high or very low temperatures.
Protecting yourself and securing the vehicle
Always fulfil legal requirements for securing a broken down vehicle. In a
number of countries it is now obligatory, for example, to turn on the hazard
warning lights and use a reflective safety vest Ÿpage 347.
When being towed with the hazard warning lights on, a change in direction or
traffic lane can be indicated as usual using the turn indicator lever. The
hazard lights will be interrupted temporarily.
Checklist
For your own safety and that of other passengers, the following points should
be observed in the order given Ÿ:
1. Park the vehicle a safe distance from traffic and on suitable ground
Ÿ.
2. Turn on the hazard warning lights with the button Ÿfig. 195.
Fig. 195 In the centre of
the instrument panel:
Switch for hazard warning
lights.