bonnet Seat Alhambra 2010 Owner's Manual

Page 61 of 413

Cockpit 60
Radio or navigation system (fitted at factory) ŸBooklet
“Radio” or ŸBooklet “Navigation system”
Storage compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hazard warning lights switch  . . . . . . . . . . . . . . . . . . . . . . .
Switches for:
Climatic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Climatronic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Right seat heating controls A . . . . . . . . . . . . . . . . . . . . . . . . .
Button for:
Anti-slip regulation (ASR) « /&&. . . . . . . . . . . . . . . . . . . . . .
Start/stop operation › . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parking distance warning system (Park Pilot) '. . . . . . . .
Parking aid system (Park Assist) i . . . . . . . . . . . . . . . . . .
Tyre pressure monitor ~ 3%4 . . . . . . . . . . . . . . . . . . . . . . . .
Running gear dynamic control (DCC) #/-&/24 – Q – 30/24 . .
Opening the tailgate ˜. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Opening and closing of electric sliding doors ¼ . . . . . . .
Locking lever to open glove compartment . . . . . . . . . . . . . . .
Position of passenger front airbag on the instrument panel .
Key-operated switch in glove box for deactivating front
passenger's airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Passenger front airbag off warning lamp . . . . . . . . . . . . . . . .
Lever for:
Manual gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12 Volt socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto Hold Switch !54/-(/,$. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electronic parking brake switch G . . . . . . . . . . . . . . . . . . . . .
Starter button (with KESSY starter and close system) . . . . . .
Ignition lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Pedals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering column adjustment lever . . . . . . . . . . . . . . . . . . . . .
Fuse box cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lever for:
Cruise control system (GRA) /&& – #!.#%, – /. – 2%35-% /
-30%%$- / -3%4- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Open bonnet lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controls for:
Electric windows
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Childproof locks r. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Note
xSome of the items of equipment listed here are fitted only on certain
models/model years or are optional extras.
xIn versions with the steering wheel on the right, the layout of the control
elements is somewhat different. But the symbols assigned to the controls
correspond to the symbols used in the versions with the steering wheel on
the left
A13
A14162
A15345
A16
179
179
A17137
A18
210
221
225
229
245
243
97
92
A19162
A2033
A2133
A2233
A23
201
201
A24175
A25221
A26210
A27195
A28195
A29201A3010
A31356
A32
239
A33304
A34
102
92

Page 64 of 413

Cockpit63
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xNever ignore the warning lamps or text messages.
xStop the vehicle safely as soon as possible.
xPark the vehicle away from the traffic, ensuring that there are no easily
inflammable materials under the vehicle which could come into contact
with the exhaust system (e.g. dry grass, fuel).
xA faulty vehicle represents a risk of accident for the driver and for other
road users. If necessary, switch on the hazard warning lamps and put out
the warning triangle to advise other drivers.
xBefore opening the bonnet, switch off the engine and allow it to cool.
xIn any vehicle, the engine compartment is a hazardous area and could
cause severe injury Ÿpage 304.
Caution
Failure to heed the warning lamps and text messages when they appear may
result in faults in the vehicle.
WARNING (continued)

Page 90 of 413

Unlocking and locking89
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a When does the system trigger an alarm?
The anti-theft alarm siren will be triggered for about 30 seconds accompa-
nied by optical warning signals for about five minutes when the vehicle is
locked and the following unauthorised actions are taken:
xWhen the door is mechanically unlocked using the vehicle key without
turning the ignition within the following 15 seconds.
xA door is opened.
xThe bonnet is opened.
xThe tailgate is opened.
xWhen the ignition is switched on with a non-authorised key.
xWhen the vehicle battery is disconnected.
xWhen there is movement inside the vehicle (vehicles with interior moni-
toring).
xWhen the vehicle is towed (vehicles with anti-tow system)
xWhen the vehicle is lifted (vehicles with anti-tow system).
xTransporting the vehicle on a ferry or by railroad (vehicles with an anti-tow
system or passenger compartment monitoring).
xUnhitch a trailer connected to the antitheft alarm Ÿpage 260.
How to turn OFF the alarm
Unlock the vehicle with the unlocking button on the key or turn on the ignition
with a valid key.
Note
The alarm will be triggered once more when anybody enters the same zone of
surveillance or any other zone. If, for example, after opening a door, the tail-
gate is also opened.
Note
The antitheft alarm is not activated when the vehicle is locked from within
using the central locking button .
Note
If the driver's door is unlocked mechanically with the key, only the driver's
door is unlocked, the rest of the doors remain locked. Only when the ignition
has been turned on will the other doors be available - but not unlocked - and
the central locking button activated.
Note
If the vehicle battery is run down or flat then the antitheft alarm will not
operate correctly.
1

Page 126 of 413

Lights and visibility125
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Windscreen wiper lever
Caution
If the ignition is switched off while the windscreen wipers are on, the wind-
screen wipers carry on wiping at the same level when the ignition is switched
back on. Ice, snow and other obstacles may damage the windscreen wiper
and the wiper motor.
Note
The windscreen wipers will only function when the ignition is switched on and
the bonnet or tailgate are closed.
Fig. 72 Using the wind-
screen wipers.
Fig. 73 Using the rear
window wipers.
Move the lever to the required position Ÿ:
OFFWindscreen wiper off.
u
Intermittent windscreen wipers wipe.
Using the control Ÿfig. 72 adjust the interval (vehicles
without the rain sensor), or the sensitivity of the rain sensor.
LOWSlow wipe.
HIGHContinuous wipe.
xBrief wipe - short wipe. Hold the lever down for more time to
increase the wipe frequency.
WAutomatic wipe for cleaning windscreens with the lever up.
ZIntermittent wipe for rear window. The rear wiper will wipe the
window approximately every 6 seconds.
\Automatic wipe for cleaning rear windows with the lever
pressed.
A0
A1AA
A2
A3
A4
A5
A6
A7

Page 128 of 413

Lights and visibility127
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Windscreen wipers service position
The wiper arms can be raised when the wipers are in service position
Ÿfig. 74. To place the windscreen wipers in the service position, proceed as
follows:
xThe bonnet must be closed Ÿpage 304.
xSwitching the ignition on and off.
xPress the windscreen wiper lever downwards briefly Ÿpage 125, fig. 72
.
Before driving, always lower the wiper arms. Using the windscreen wiper
lever, the windscreen wiper arms return to their initial position.
Lifting and returning windscreen wiper arms
xPlace the wiper arms in the service position Ÿ.
xOnly hold the wiper arms at the point where the blade is fixed.
Caution
xTo prevent damage to the bonnet and the wiper arms, only leave them in
the service position.
xBefore driving, always lower the wiper arms.
Fig. 74 Wipers in service
position.
A4

Page 130 of 413

Lights and visibility129
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Note
Clean the sensitive surface of the rain sensor regularly and check the blades
for damage Ÿpage 128, fig. 76 (arrow).
Note
To remove wax and coatings, we recommend a window cleaner containing
alcohol.
Checking and topping up the windscreen washer bottle with
water
Check the water level in the windscreen washer bottle regularly and top up as
required.
xOpen the bonnet ’ Ÿpage 304.
xThe washer bottle is marked with the symbol Y on the lid Ÿfig. 77.
xCheck there is enough water in the bottle.
xTo top up, mix water with a window cleaner recommended by SEAT Ÿ.
Please follow the instructions for use found on the packaging.
xIn cold weather, a special antifreeze should also be added to prevent the
water from freezing Ÿ.
Bottle capacity
The bottle holds approximately 3.0 litres; in vehicles with headlight washer,
it is approximately 7.0 litres.
WARNING
Never mix an unsuitable antifreeze or other similar products with the wind-
screen washer water. A greasy layer may be formed on the windscreen
which will impair visibility.
xUse clean water with a window cleaner recommended by SEAT.
xIf necessary, add a suitable antifreeze to the water bottle.
Caution
xDo not mix cleaning products recommended by SEAT with other products.
This could lead to flocculation and may block the windscreen washer jets.
xWhen topping up service fluids, make absolutely certain that you fill the
fluids into the correct reservoirs. Failure to observe this point will result in
serious malfunctions and engine damage!
Fig. 77 In the engine
compartment: windscreen
washer bottle top.

Page 225 of 413

Driving 224
Important conditions for the engine to automatically switch off
xThe driver seat belt must be buckled.
xThe driver door must be closed.
xThe bonnet must be closed.
xThe factory-fitted towing bracket must not be electrically connected to a
trailer.
xA minimum engine temperature has been reached.
xThe vehicle has moved since the last stop.
xIn vehicles with Climatronic: The temperature inside the vehicle is within
the preset temperature range.
xThe temperature set is neither very high nor very low.
xThe air conditioning defrost function is not switched on.
xIn vehicles with Climatronic: the blower has not been manually set to a
high speed.
xThe power level of the vehicle's battery is sufficient.
xThe vehicle's battery temperature is neither too high nor too low.
xThe vehicle is not on a steep gradient or slope.
xThe front wheels are not overly turned.
xThe heated windscreen is not switched on.
xReverse gear is not engaged.
xThe park assist system is not switched on.
Conditions for automatically restarting the engine
The engine may automatically restart under the following conditions:
xIf the vehicle interior is too hot or too cold.
xIf the vehicle moves.
xIf the vehicle's battery voltage drops.
Conditions requiring the key to restart the engine
The engine must be started using the key under the following conditions:
xIf the driver unbuckles his/her seat belt.
xIf the driver's door is opened.
xIf the bonnet is opened.
xIn vehicles with a manual gearbox: If a gear has been selected.
Switching Start-Stop mode on and off manually
xPress the button on the centre console Ÿpage 223, fig. 147.
xThe button will light up when the Start-Stop function is switched off.
The engine will start immediately if the vehicle is in Stop mode when it is
switched off manually.
WARNING
The brake servo and the power steering do not work when the engine is
switched off.
xNever allow the vehicle to move when the engine is switched off.
Caution
Using the Start-Stop function for a long period at very high outdoor tempera-
tures could damage the vehicle's battery.
Note
In some cases, you may have to restart the vehicle using the key. Observe the
corresponding message on the instrument panel display.

Page 272 of 413

Vehicle maintenance and cleaning271
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xWashing the vehicle in low temperatures: When washing the vehicle with
a hose, do not direct water into the lock cylinders or the gaps around the
doors, tailgate, or sunroof. Locks and seals could freeze!
Caution
To prevent damage to the vehicle, please observe the following before
entering an automatic car wash:
xCompare the distance between the vehicle wheels and the distance
between the guide-rails of the car wash to prevent damage to the wheels and
tyres!
xSwitch off the rain sensor and the Auto Hold function before entering a car
wash.
xCompare the height and width of your vehicle with the available height
and width when entering and driving through the car wash.
xFold in exterior mirrors Electrically retractable exterior mirrors must NOT
be folded in or out by hand. Always use the electrical power control.
xTo avoid damaging the bonnet paintwork, rest the wipers on the wind-
screen after drying them. Do not let them fall!
xLock the tailgate to prevent it from opening unexpectedly while inside the
car wash.
Washing the vehicle with high pressure cleaning equipment
When cleaning the vehicle with a high-pressure cleaner, always follow the
operating instructions for the equipment. Pay special attention to the
required pressure of the jet and the distance between the jet and the vehicle
Ÿ.
Keep a suitable distance from soft materials, such as rubber hoses or insu-
lating material, and from the parking distance warning system sensors. The parking distance sensors are fitted in the rear bumpers and, where appli-
cable, in the front bumpers Ÿ.
Do not use a nozzle that sprays the water out in a direct stream or one that
has a rotating jet for forcing off dirt Ÿ.
WARNING
The incorrect use of high pressure cleaning equipment could result in
permanent damage, visible or invisible, to the tyres or other materials. This
could result in serious accident.
xEnsure there is a suitable distance between the nozzle and the tyres.
xNever wash tyres with a concentrated jet or so-called “dirt blasters”.
Even at large spraying distances and short cleaning times, you may
damage the tyres.
WARNING
After the vehicle has been washed, the braking effect will be reduced (and
the braking distance increased) due to moisture (and ice in winter) on the
brakes.
xDry the brakes and remove ice by braking carefully. Ensure that you are
not endangering other road-users or breaking traffic regulations in the
process.
Caution
xThe temperature of the water must not be above +60 °C (+140 °F).
xTo avoid damage to the paintwork, do not wash the vehicle in full sun.
xThe sensors on the bumpers should be kept clean and free of ice at all
times to ensure the parking distance warning system and the parking aid
system operate correctly. When cleaning with pressure hoses and steam
cleaners, the sensors should be sprayed only briefly. A distance of 10 cm
between the sensors and the steam / hose nozzle must be observed.

Page 284 of 413

Vehicle maintenance and cleaning283
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Notes for the user
Labels and plates
Some parts in the engine compartment come from the factory with certifi-
cates of safety, labels or plates containing important information regarding
the operation of the vehicle, for example, on the petrol cap, on the
passenger's sun visor, on the driver's door strut, or on the floor of the luggage
compartment.
xNever remove these certificates of safety, labels or plates, and ensure
they are kept in good condition and are legible.
xIf a vehicle part, bearing a certificate of safety, label or plate, is replaced,
the qualified workshop should attach the information back in the same place.
Certificate of safety
A certificate of safety on the door strut states that all the safety standards and
regulations established by the national traffic authorities responsible for
road safety were met at the time of manufacture. It may also give the month
and year of manufacture, together with the chassis number.
Warning of high voltage label*
There is a label close to the bonnet lock which warns of high voltage in the
vehicle electrical installation. The vehicle ignition system complies with
several standards, including the Canadian standard, ICES-002.
Using your vehicle in other countries and continents
The vehicle is manufactured at the factory for use in a particular country in
accordance with the national legislation in force at the time of manufacture.If the vehicle is sold in another country or used in another country for an
extended period of time, the applicable legislation of that country should be
observed.
It may be necessary to fit or remove certain pieces of equipment or to deacti-
vate certain functions. Service work may also be affected. This is particularly
true if the vehicle is used in a different climate for an extended period of time.
As there are different types of frequency bands around the world, you may
find that the radio or navigation system supplied at the factory does not work
in another country.
Caution
xSEAT does not accept liability for any damage to the vehicle due to the use
of a lower quality fuel, an inadequate service or the non-availability of
genuine spare parts.
xSEAT does not accept liability if the vehicle does not comply in part or in
full with the legal requirements of other countries or continents.
Radio reception and the aerial
The aerial of radio and navigation systems fitted at the factory may be
mounted in different parts of the vehicle:
xOn the inside of the rear window, next to the rear window heating,
xon the inside of the rear side windows,
xon the inside of the windscreen,
xon the roof of the car.
Aerials mounted on the inside of a window can be recognised by the fine
wires.

Page 290 of 413

Accessories, parts replacement and modifications289
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a The storing of the data allows specialised workshops to detect and repair
faults. Stored data may include:
xData relating to the engine or the gearbox
xSpeed
xDirection of travel
xBraking force
xDetection of seat belt
The vehicle control units never record conversations held by passengers in
the vehicle.
In vehicles equipped with an emergency call function via the mobile phone or
other appliances connected in the vehicle, it is possible to send the vehicle
position. If the control unit records an accident with airbag activation, the
system may automatically send a signal. This will depend on the network
operator. Normally, transmission is only possible in areas with good
coverage.
Event Data Recorder
The vehicle is not fitted with an event data recorder.
An event data recorder temporarily stores the vehicle information. Therefore,
in the event of accident, it is possible to obtain detailed information about
how the accident occurred. For example, in vehicles with airbag systems,
data relating to speed of impact, seat belt status, seat positions and airbag
activation times may be stored. The volume of data depends on the manufac-
turer.
Event data recorders can only be mounted with authorisation from the vehicle
owner and, in some countries, they are governed by local legislation.
Reprogramming control units
On the whole, all the data required for the component management is stored
in the control units. The programming of certain convenience functions, such
as the convenience indicators, individual door opening and instructions on
the display can be modified using special equipment at the workshop. If this is the case, the information and descriptions given in the instructions manual
will not match the original functions. Therefore, SEAT recommends that any
modifications are recorded in the section “Other workshop notes” in the
Maintenance Programme.
The Technical Service must have a record of any modification to the program-
ming.
Reading the vehicle fault memory
There is a diagnostics connector in the vehicle interior for reading the vehicle
fault memory. The fault memory documents errors and deviations from the
theoretical values of the electronic control units.
The diagnostics connector is in the driver's side footwell area, next to the
lever for opening the bonnet, below a cover.
The fault memory should only be read and reset by a qualified workshop.
Using a mobile telephone in a vehicle without connection to
an exterior aerial
Mobile telephones transmit and receive radio waves, both when in use and
when on stand-by. Scientific studies state that radio waves exceeding certain
values may be harmful to the human body. International committees and
authorities have established limits and directives in order to ensure electro-
magnetic radiation from mobile phones remains within certain limits that do
not endanger human health. However, there is no available conclusive scien-
tific evidence that cordless phones are completely safe.
Therefore, some experts recommend that use of mobile phone be kept to a
minimum until the results of current research are published.
When a mobile phone not connected to an exterior aerial is used inside the
vehicle, the electromagnetic radiation may be greater than if the mobile
phone were connected to a built-in aerial or to another exterior aerial.

Page:   1-10 11-20 21-30 next >