change wheel Seat Alhambra 2010 Owner's Manual

Safe driving13
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xKeep both feet in the footwell so that you have the vehicle under control
at all times.
Also valid for the front passenger:
xMove the front passenger seat back as far as possible for optimum protec-
tion should the airbag deploy.
Transporting objects
Introduction
Always transport heavy loads in the trunk and place the seat backs in a
vertical position. Always use the anchors provided with suitable rope to
secure heavy objects. Never overload the vehicle. Both the carrying capacity
as well as the distribution of the load in the vehicle have effects on the driving
behaviour and braking ability Ÿ.
Additional information and warnings:
xTa ilga te Ÿpage 97
xTo lower the passenger seat back Ÿpage 137
xLight Ÿpage 113
xLuggage compartment Ÿpage 146
xRoof carrier Ÿpage 159
xTo wi ng m o d e Ÿpage 260
xWheels and tyres Ÿpage 323
WARNING
Unsecured or incorrectly secured objects can cause serious injury in case
of a sudden manoeuvring or breaking or in case of an accident. This is espe-cially true when objects are struck by a detonating airbag and fired through
the vehicle interior. To reduce the risks, please note the following:
xSecure all objects in the vehicle. Always keep equipment and heavy
objects in the luggage compartment.
xAlways secure objects with suitable rope or slings so that they cannot
enter the areas around the frontal or side airbags in case of sudden braking
or an accident.
xAlways ensure that objects inside the vehicle cannot move into the area
of the bags while driving.
xWhile driving, always keep object compartments closed.
xRemove all objects from the passenger seat when this is followed down.
When the seat back is folded down, it presses on small and light objects
and these are detected by the weight sensor on the seat; this sends false
information to the airbag control unit.
xWhile the backrest of the front passenger's seat is folded, the frontal
airbag must remain disconnected and the PASSENGER AIRBAG OFF  light
on.
xObjects secured in the vehicle should never be placed in such a way as
to make passengers sit in an incorrect position.
xIf secured objects occupy a seat then this should not be occupied or
used by anybody.
WARNING
The driving behaviour and braking ability change when transporting heavy
and large objects.
xAdjust your speed and driving style to visibility, road, traffic and
weather conditions.
xAccelerate gently and carefully.
xAvoid sudden braking and manoeuvres.
WARNING (continued)

Seat belts 20
Even at low speeds, the forces acting on the body in a collision are so great
that it is not possible to brace oneself with just one's arms and hands. In a
frontal collision, unbelted passengers are thrown forward and will make
violent contact with the steering wheel, dash panel, windscreen or whatever
else is in the way Ÿpage 19, fig. 7.
The airbag system is not a substitute for seat belts. When triggered, airbags
provide only additional protection. Airbags do not deploy in all types of acci-
dent. All occupants (including the driver) must be wearing seat belts properly
during the trip, even if the vehicle is equipped with airbag systems. This will
reduce the risk of critical or fatal injuries in the event of an accident – regard-
less of whether an airbag is fitted for the seat.
The airbag is only deployed once. To achieve the best possible protection, the
seat belt must always be worn properly so that you will be protected in acci-
dents in which no airbag is deployed. Vehicle occupants not wearing belts
could be thrown from the vehicle and sustain even more severe or fatal inju-
ries.
It is also important for the rear passengers to wear seat belts properly, as they
could otherwise be thrown forward violently in an accident. Rear passengers
who do not use seat belts endanger not only themselves but also the driver
and other occupants Ÿpage 19, fig. 8.Seat belt protection
Wearing a correctly fastened seat belt can significantly change the situation.
Properly worn seat belts hold the vehicle occupants in the correct sitting posi-
tions and substantially reduce the kinetic energy in the event of an accident.
Seat belts also help to prevent uncontrolled movements that could lead to
severe injuries. In addition, properly worn seat belts reduce the danger of
being thrown from the car Ÿfig. 9.
Passengers wearing their seat belts correctly benefit greatly from the ability
of the belts to absorb kinetic energy. The front crumple zones and other
passive safety features (such as the airbag system) are also designed to
absorb the kinetic energy generated in a collision. Taken together, all these
features reduce the energy released and decrease the risk of injury.
Our examples describe frontal collisions. Of course, properly worn seat belts
substantially reduce the risk of injury in all other types of accidents. This is
why it is so important to fasten seat belts before every trip, even when just
driving “around the corner”. Ensure that your passengers wear their seat
belts as well.
Fig. 9 Drivers with prop-
erly worn seat belts will
not be thrown forward in
the event of sudden
braking.

Cockpit 72
Using the menus on the instrument panel
Enabling the main menu
xSwitch the ignition on.
xIf a message or vehicle symbol is displayed, press (Ÿfig. 38 or
Ÿfig. 39).
xIf managed from the windscreen wiper lever: the main menu list is
displayed.
xIf managed from the multifunction steering wheel: the main menu list is
not displayed. To scroll through the options of the main menu, press the
arrow keys or several times Ÿpage 73.
Select a submenu
xPress the rocker switch Ÿfig. 38 upwards or downwards, or, on the
multifunction steering wheel, the arrow keys or , until reaching the
required menu option.
xThe selected option is displayed between two horizontal lines. In addi-
tion, a triangle is displayed on the right y.
xTo select the submenu, press .
Making changes according to the menu
xUse the rocker switch on the windscreen wiper lever or the arrow keys on
the multifunction steering wheel to make the required modifications. If the
switch or keys are held down, the scroll speed is faster (fast forward or return).
xMark or confirm the selected option with .
Returning to the main menu
xVia the menu: in the submenu, select the option Return to exit the
submenu.
xIf managed from the windscreen wiper lever: hold down the rocker switch.
xIf managed from the multifunction steering wheel: press button .
Fig. 38 In vehicles
without multifunction
steering wheel: On the
windscreen washer lever:
button to confirm the
menu point and rocker
switch to change the
menu
AA
AB
Fig. 39 Right side of
multifunction steering
wheel: Buttons to access
the instrument panel
menus.
OKAA
ƒ„
AB*+
OK
OK
E

Lights and visibility 120
function is switched on. If the equipment includes the light sensor, the
lighting around the exterior mirrors only comes when it is dark.
Note
The time taken for the headlights to go off can be changed in the menu Lights
& Visibility and the function can be switched on or off Ÿpage 70.
Note
When the “Coming home” function is on, if the vehicle door is opened there
is no audible warning signal to advise that the light is still on.
Headlight range control, instrument and switch lighting
Instrument and switch lighting
When the headlights are switched on, the brightness of the instruments and
switch lighting can be regulated to suit your requirements by turning the
switch Ÿfig. 68 .
Headlight range control
The headlight range control Ÿfig. 68 is modified according to the value
of the headlight beam and the vehicle load status. This offers the driver
optimum visibility and the headlights do not dazzle oncoming drivers Ÿ.
The headlights can only be adjusted when the dipped beam is switched on.
To reset, turn switch Ÿfig. 68 :
Dynamic headlight range control
The control is not mounted in vehicles with dynamic headlight range
control. The headlight range is automatically adjusted according to the
vehicle load status when the headlights are switched on.
WARNING
Heavy objects in the vehicle may mean that the headlights dazzle and
distract other drivers. This could result in serious accident.
Fig. 68 Next to the
steering wheel: instru-
ment and switch lighting
control and headlight
range control .
A1A2
ValueVehicle load statusa)
a)If the vehicle load does not correspond to those shown in the table, it is possible to
select intermediary positions.
–Two front occupants, luggage compartment empty
1All seats occupied, luggage compartment empty
2All seats occupied, luggage compartment full. With trailer
and minimum support load
3Driver only, luggage compartment full. With trailer and
maximum support load
A1
A1
A2
A2
A2
A2

Lights and visibility 126
Note
The intermittent wiper speed varies according to the vehicle speed. The faster
the vehicle is moving, the more often the windscreen is cleaned.
Note
The rear wiper is automatically switched on when the windscreen wiper is
connected and the car is in reverse gear.
Windscreen wiper functions
Heated windscreen washer jets
The heating only thaws the frozen jets, it does not thaw the water in the
washer hoses. The heated windscreen washer jets automatically adjust the
heat depending on the ambient temperature, when the ignition is switched
on.Headlight wash /wipe system
The headlight washers/wipers clean the headlight lenses.
After the ignition is switched on, the first and every fifth time the windscreen
washer is switched on, the headlights are also washed. Therefore, the wind-
screen wiper lever should be pulled towards the steering wheel when the
dipped beam or main beam are on. Any incrusted dirt (such as insects)
should be cleaned regularly (e.g. when refuelling).
To ensure the headlight washers work correctly in winter, any snow which has
got into the bumper jet supports should be cleaned away. If necessary,
remove snow with an anti-icing spray.
Note
The wiper will try to wipe away any obstacles that are on the windscreen. The
wiper will stop moving if the obstacle blocks its path. Remove the obstacle
and switch the wiper back on again.Windscreen wiper performance in different situations:
If the vehicle is at a stand-
still:The activated position provisionally changes
to the previous position.
During the automatic wipe:
The air conditioning comes on for approxi-
mately 30 seconds in air recirculation mode
to prevent the smell of the windscreen
washer fluid entering the inside of the vehi-
cle.
For the intermittent wipe:The intervals between wipes vary according
to the speed of the vehicle. The higher the
vehicle speed the shorter the intervals.

Seats and storage compartments 146
Loading luggage compartment
Introduction
Always transport heavy loads in the trunk and place the seat backs in a
vertical position. Always use the fastening rings with suitable rope or straps.
Never overload the vehicle. Both the carrying capacity as well as the distribu-
tion of the load in the vehicle have effects on the driving behaviour and
braking ability Ÿ.
Additional information and warnings:
xAirbag system Ÿpage 33
xLight Ÿpage 113
xTranspor ting Ÿpage 13
xTo wi ng m o d e Ÿpage 260
xWheels and tyres Ÿpage 323
WARNING
When the vehicle is not in use or being watched, always lock the doors and
the tailgate to reduce the risk of serious injury or death.
xDo not leave children unwatched, especially when the tailgate is open.
Children could climb into the luggage compartment, close the tailgate from
inside and be unable to escape themselves. This could lead to serious
injury or death.
xNever allow children to play in or around the vehicle.
xNever transport people in the luggage compartment.
WARNING
Unsecured or incorrectly secured objects can cause serious injury in case
of a sudden manoeuvring or breaking or in case of an accident. This is espe-cially true when objects are struck by a detonating airbag and fired through
the vehicle interior. To reduce the risks, please note the following:
xSecure all objects in the vehicle. Always keep equipment and heavy
objects in the luggage compartment.
xAlways secure objects with suitable rope or straps so that they cannot
enter the areas around the frontal or side airbags in case of sudden braking
or an accident.
xWhile driving, always keep object compartments closed.
xDo not place hard, heavy or sharp objects inside the passenger
compartment, in open storage compartments, the rear shelf or on the
dashboard.
xRemove hard, heavy and sharp objects from clothes and pockets inside
the vehicle and store securely.
WARNING
The transport of heavy object changes vehicle handling and increases
braking distance. Heavy loads that have not been stored or secured
correctly could cause loss of control and result in serious injury.
xThe vehicle handling changes when transporting heavy objects due to
a change in the centre of gravity.
xDistribute the load as uniformly and as low down on the vehicle as
possible.
xStore heavy objects in the luggage compartment as far from the rear
axle as possible.
Caution
xHard objects on the shelf could chafe the wires of the heating element
and antenna of the rear window and cause damage.
xThe side window antenna could be damaged due to chafing from objects.
WARNING (continued)

Seats and storage compartments159
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Roof carrier system
Introduction
The vehicle roof has been designed to optimise aerodynamics. For this
reason, conventional roof carrier systems cannot be secured to the roof rails.
Given that the water drains have been incorporated into the roof for aerody-
namic reasons, only the SEAT approved basic supports and roof carrier
systems can be used.
When should the roof carrier system be removed?
xWhen it is not being used.
xWhen the vehicle is being washed in a car wash.
xWhen the vehicle height exceeds the maximum height (for example, in a
garage).
Additional information and warnings:
xLight Ÿpage 113
xTransporting Ÿpage 13
xEcological driving Ÿpage 252
xWheels and tyres Ÿpage 323
xAccessories, parts replacement, repairs and modifications Ÿpage 285
WARNING
The risk of an accident is increased by transporting heavy or bulky loads on
the roof, which affects the car's handling by shifting the centre of gravity
and increasing susceptibility to cross winds.
xAlways secure loads correctly with suitable and undamaged attach-
ment rope or straps.
xLarge, heavy, wide and flat loads negatively affect the vehicle aerody-
namics, centre of gravity and handling.
xAvoid brusque manoeuvres and sudden braking.
xAdjust your speed and driving style to visibility, road, traffic and
weather conditions.
Caution
xAlways remove the roof carrier system from the roof before entering a car
wash.
xThe height of your vehicle is changed by the installation of the roof carrier
and the load secured on it. Compare the vehicle height with the passage
height, for example in underground car parks or entering garage doors.
xThe roof antenna, the range of the panoramic sliding roof and the tailgate
should not be affected by the roof carrier system and the load being trans-
ported.
xTake extra care not to let the tailgate strike the roof load when opening.
For the sake of the environment
The vehicle uses more fuel when the roof carrier system is fitted.
WARNING (continued)

Seats and storage compartments 160
Securing the base supports and roof carrier system
The mounts are the basis of a complete roof carrier system. Special fixtures
must then be added in order to safely transport luggage, bicycles, skis, surf
boards or boats on the roof. All these system components are available from
an Authorised Service Centre.
It will only be possible to install a basic support or roof carrier system if the
vehicle has a roof rail.
Securing the base supports and roof carrier system
Always secure the base supports and roof carrier system correctly.
The roof carrier system must always be installed exactly according to the
instructions provided.
The position holes are located on the inner side of the rail Ÿfig. 107.
WARNING
If the base supports and the roof carrier system are incorrectly fitted or
used in an unsuitable manner, the entire system could break free causing
accident and injury.
xAlways take the manufacturer assembly instructions into account.
xOnly use base supports and roof carrier systems that are not damaged
and are correctly fitted.
xThe base support should only be fitted to the points indicated in the
diagram Ÿfig. 107.
xSecure the base supports and roof carrier system correctly.
xCheck the screw fittings and attachments before driving and after a
short distance. During each long journey, check the attachments during
every break.
xAlways fit the roof carrier system correctly for wheels, skis and surf-
boards.
xNever change or repair the basic supports or roof carrier system.
Note
Read and take into account the instructions included with the roof carrier
system fitted and keep them in the vehicle.
Loading the roof carrier system
Loads can only be correctly secured when the roof carrier system is correctly
fitted Ÿ.
Maximum authorised roof load
The maximum authorised roof load is 100 kg (about 220 lbs). The roof load
includes the roof carrier system and the load being transported Ÿ.
Fig. 107 Attachment
points for the basic
support and the roof
carrier system.

Heating, Ventilation and Air conditioning185
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Air vents
Air vents
Never close the air vents Ÿfig. 131 completely to ensure heating,
cooling and ventilation inside the vehicle.
xTurn the thumbwheel in the required direction to open and close the air
vents.
xChange the air direction using the ventilation grille lever.
There are additional vents in the footwell areas and in the rear of the
passenger compartment.
Caution
Never place food, medicines or other heat-sensitive objects close to the air
vents. Food, medicines and other heat-sensitive objects may be damaged or
made unsuitable for use by the air coming from the air vents.
Air recirculation mode
Important
Air recirculation works in two ways:
Air recirculation mode
 prevents the ambient air from entering the vehicle
interior.
When the outside temperature is very high or very low, selecting manual air
recirculation mode for a short period refreshes or heats the vehicle interior
more quickly.
For safety reasons, air recirculation mode is switched off when the button
is pressed or the air distributor turned to
< Ÿ.
Fig. 131 Air vents in the instrument panel.
AA
Manual air recirculation mode.
oAutomatic air recirculation mode.
<

Driving 194
WARNING
The counter steering assistance system combined with ESP helps the
driver to steer the vehicle in critical driving conditions. At all times, it is the
driver who steers the vehicle. The counter steering system does not steer
the vehicle.
Adjusting the steering wheel position
Adjust the steering wheel before your trip and only when the vehicle is
stationary.
xPush the lever Ÿfig. 133 downwards.
xAdjust the steering wheel so that you can hold onto the steering wheel
with both hands on the outside of the ring at the 9 o'clock and 3 o'clock posi-
tions and your arms slightly bent.
xPush the lever firmly upwards until it is flush to the steering column
Ÿ.
WARNING
Incorrect use of the steering wheel adjustment function and an incorrect
adjustment of the steering wheel can result in severe or fatal injury.
xAfter adjusting the steering column, push the lever Ÿfig. 133
firmly upwards to ensure the steering wheel does not accidentally change
position while driving.
xNever adjust the steering wheel while the vehicle is in motion. If you
need to adjust the steering wheel while the vehicle is in motion, stop safely
and make the proper adjustment.
xThe adjusted steering wheel should be facing your chest and not your
face so as not to hinder the driver's frontal airbag protection in the event of
an accident.
xWhen driving, always hold the steering wheel with both hands on the
outside of the ring at the 9 o'clock and 3 o'clock positions to reduce injuries
when the driver's frontal airbag deploys.
xNever hold the steering wheel at the 12 o'clock position or in any other
manner (e.g. in the centre of the steering wheel). In such cases, if the
driver's airbag deploys, you may sustain injuries to your arms, hands and
head.
Fig. 133 Mechanical
steering wheel adjust-
ment.
A1
A1